Rohm BD82A26MUF-M Manuale utente

BD82A26MUF-M Evaluation Board

REFLED003-EVK-003

Notice

www.rohm.com HVA01E

＜High Voltage Safety Precautions＞

◇Read all safety precautions before use

Please note that this document covers only the BD82A26MUF-M evaluation board

(REFLED003-EVK-003) and its functions. For additional information, please refer to the

datasheet.

To ensure safe operation, please carefully read all precautions before

handling the evaluation board

Depending on the configuration of the board and voltages used,

Potentially lethal voltages may be generated.

Therefore, please make sure to read and observe all safety precautions described in

the red box below.

Before Use

[1] Verify that the parts/components are not damaged or missing (i.e. due to the drops).

[2] Check that there are no conductive foreign objects on the board.

[3] Be careful when performing soldering on the module and/or evaluation board to ensure that

solder splash does not occur.

[4] Check that there is no condensation or water droplets on the circuit board.

During Use

[5] Be careful to not allow conductive objects to come into contact with the board.

[6] Brief accidental contact or even bringing your hand close to the board may result in

discharge and lead to severe injury or death.

Therefore, DO NOT touch the board with your bare hands or bring them too close to the board.

In addition, as mentioned above please exercise extreme caution when using conductive tools such

as tweezers and screwdrivers.

[7] If used under conditions beyond its rated voltage, it may cause defects such as short-circuit or,

depending on the circumstances, explosion or other permanent damages.

[8] Be sure to wear insulated gloves when handling is required during operation.

After Use

[9] The ROHM Evaluation Board contains the circuits which store the high voltage. Since it stores the

charges even after the connected power circuits are cut, please discharge the electricity after

using it, and please deal with it after confirming such electric discharge.

[10] Protect against electric shocks by wearing insulated gloves when handling.

This evaluation board is intended for use only in research and development facilities and

should by handled only by qualified personnel familiar with all safety and operating

procedures.

We recommend carrying out operation in a safe environment that includes the use of high

voltage signage at all entrances, safety interlocks, and protective glasses.

1/9

2023 ROHM Co., Ltd.

66UG041E Rev.001

Sep.1.2023

User’s Guide

LED Driver for Automotive Panel Backlight

6ch White LED Driver Built-in Current Driver

Boost DC/DC Converter for Automotive

BD82A26MUF-M Evaluation Board

REFLED003-EVK-003

Introduction

This user’s guide will provide the necessary steps to operate the Evaluation Board of ROHM’s BD82A26MUF-M LED Driver.

This document includes the external parts, operating procedures and application data.

Description

This Evaluation Board was developed for ROHM’s LED Driver BD82A26MUF-M. BD82A26MUF-M is a white LED driver for LCD

backlight. It has 6 built-in current drivers for LED drive, making it ideal for high brightness LED drive. LED pin max voltage is 50

V, making it suitable for driving large LCD panels. The dimming is controlled by the PWM signal and can be set up to 20,000:

1@100 Hz. It also supports analog dimming and can accommodate even higher brightness ranges by combining with PWM

dimming. DC/DC converters can be controlled for boost applications, and the input operating voltage range is 3.0V to 48V.

Application

Automotive backlight application for CID, cluster panel, car navigation, HUD, or car audio system.

Evaluation board operating condition (default setting)

Table 1. Evaluation board operating condition (default setting)

Parameter Min Typ Max Unit

Power supply voltage

7 13.5 18 V

LEDs in series 6 - 8 pcs

LEDs in parallel - 6 - ch

Output voltage

19 - 26.5 V

Output current (per channel) - 125 - mA

DC/DC oscillation frequency - 300 - kHz

Over voltage limit - 31 - V

Over current limit - 5.4 - A

*1 This indicates the voltage near the VCC pin. Be careful of voltage drop by the impedance of power line.

*2 Output voltage is determined by the Vf value of the connected LED and the numbers of series. Since this evaluation board has

a boost-configuration, output voltage should be higher than input voltage. Also, output voltage should be lower than OVP voltage.

2/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Evaluation board

Figure 1. Top view F

igure 2. Bottom view

Evaluation board setup

Figure 3. Evaluation board setup

Operating procedure

1. Connect panel or LEDs to evaluation board. (Anode to VOUT-pin. Cathode to LEDx-pin.)

2. Connect power supply to +B-pin and –B-pin of the evaluation board.

3. Connect power supply to EN-pin. It must be less than 7V.

4. Connect pulse generator to PWM-pin. It should be 100Hz to 25kHz and the minimum pulse width must be

longer than 0.5μs.

5. Turn on the power supply for +B-pin.

6. Turn on the power supply for EN-pin.

7. Turn on the pulse generator for PWM-pin.

3/9

Sep.2023

User’s Guide

REFLED003-EVK-003

20 kΩ

100 kΩ

LED1

LED2

LED3

LED4

LED5

LED6

REG50

Operation mode settings

The table below describes the settings for SYNC, PD, SHT terminals.

Table 2. Mode settings

Terminal Setting Function

SYNC

GND or OPEN Fixed Frequency Mode Determined by RRT

VREG50 Spread Spectrum Mode (SSCG) of the Frequency

Determined by RRT

Pulse Input Mode to Synchronize with the Frequency Input to the

PD GND or OPEN Phase delay function is disabled

VREG50 Phase delay function is enabled

SHT GND (OPEN is not allowed) LED short protection voltage: V

LEDn

> 4.5V(typ)

DC voltage Input LED short protection voltage: V

LEDn

> input voltage x 10

For unused channels, pull up the LED pin (LED1 to LED6) to REG50

with 100kΩ and pull down to GND with 20kΩ.

Pin configuration

Figure 5. Pin configuration

Figure 4. Setting LED6 to Unused

4/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Evaluation board schematic

Figure 6. Evaluation board schemati

Figure 6. Evaluation board schematic

5/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Parts list

Table 3. Parts list

No Package Parameters Part name(series) Type Manufacturer

CB1 1005 0.1μF, X7R, 50V GCM155R71H104KE02 Ceramic Murata

CB2 3225 10μF, X7S, 50V GCM32EC71H106KA03 Ceramic Murata

CM1 L12.9 x W6.6 x T9.4mm Open - - -

L1 W7.0 x H4.5 x L7.4mm 4.7μH, 4.1A CLF7045NIT-4R7N-D Inductor TDK

CVCC1 1005 Open - Ceramic -

CVCC2 Φ10 x 10mm 220μF, 50V Nichicon UCD series Electrolytic Nichicon

CVCC3 2012 1μF, X7R, 50V GCM21BR71H105KA03 Ceramic Murata

RCSH 1632 27mΩ, 1.0W LTR18 series Resistor ROHM

M1 HSMT8AG -40V, -27A RQ3G270BJ MOSFET ROHM

CIN1 3225 10μF, X7S, 50V GCM32EC71H106KA03 Ceramic Murata

CIN2 1005 0.1μF, X7R, 50V GCM155R71H104KE02 Ceramic Murata

D1 PMDTM 60V, 5A RB088LAM-60TF SBD ROHM

L2 W10.5 x H6.5 x

L10.0mm 33μH, 8.8A SPM10065VT-330-D Inductor TDK

RG 2012 10Ω, 1/8W MCR10 series Resistor ROHM

M2 HSMT8AG 60V, 12A RQ3L120BKFRA MOSFET ROHM

RCSL 1220 56mΩ, 1.0W LTR10L series Resistor ROHM

RCS 1005 Short - Resistor -

CCS 1005 Open - Ceramic -

D2 PMDTM 60V, 5A RB088LAM-60TF SBD ROHM

COUT1 1005 0.01μF, X7R, 50V GCM155R71H103KA55 Ceramic Murata

COUT2 1005 0.1μF, X7R, 50V GCM155R71H104KE02 Ceramic Murata

COUT3 3225 10μF, X7S, 50V GCM32EC71H106KA03 Ceramic Murata

COUT4 3225 10μF, X7S, 50V GCM32EC71H106KA03 Ceramic Murata

COUT5 Φ8 x 10mm 68μF, 50V GYA1H680MC Hybrid Nichicon

COUT6 1005 Open - Ceramic -

RISET 1005 20kΩ, 1/16W MCR01 series Resistor ROHM

RRT 1005 33kΩ, 1/16W MCR01 series Resistor ROHM

ROVP1 1005 11kΩ, 1/16W MCR01 series Resistor ROHM

ROVP2 1005 330kΩ, 1/16W MCR01 series Resistor ROHM

COVP 1005 Open - Ceramic -

RDIMSEL1 1005 Short - Resistor -

RDIMSEL2 1005 Open - Resistor -

RPLS1 1005 100kΩ, 1/16W MCR01 series Resistor ROHM

RPLS2 1005 100kΩ, 1/16W MCR01 series Resistor ROHM

RPC 1005 200Ω, 1/16W MCR01 series Resistor ROHM

CPC1 1608 1μF, X7R, 16V GCM188R71C105KA49 Ceramic Murata

CPC2 1005 Open - Ceramic -

6/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Parts list - continued

Table 3. Parts list - continued

No Package Parameters Part name(series) Type Manufacturer

CREG251 1005 0.22μF, X7R, 16V GCM155R71C224KE02 Ceramic Murata

CREG501 1608 2.2μF, X7S, 10V GCM188C71A225KE01 Ceramic Murata

CREG502 1005 Open - Ceramic -

CP1 3225 10μF, X7S, 50V GCM32EC71H106KA03 Ceramic Murata

CP2 1608 2.2μF, X7S, 10V GCM188C71A225KE01 Ceramic Murata

RFAIL1 1005 100kΩ, 1/16W MCR01 series Resistor ROHM

RFAIL2 1005 100kΩ, 1/16W MCR01 series Resistor ROHM

REN1 1005 Open - Resistor -

REN2 1005 Open - Resistor -

RSYNCU 1005 Short - Resistor -

RSYNCD 1005 Open - Resistor -

RPWM 1005 Open - Resistor -

CSNB1 1005 Open - Ceramic -

CSNB2 1005 Open - Ceramic -

RSNB1 3225 Open - Resistor -

RSNB2 3225 Open - Resistor -

CLED1D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

CLED2D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

CLED3D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

CLED4D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

CLED5D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

CLED6D 1005 470pF, C0G, 50V GCM1555C1H471JA16 Ceramic Murata

RLED1 1005 Open - Resistor -

RLED2 1005 Open - Resistor -

RLED3 1005 Open - Resistor -

RLED4 1005 Open - Resistor -

RLED5 1005 Open - Resistor -

RLED6 1005 Open - Resistor -

FB1 1005 Short - - -

FB2 1005 Short - - -

FB3 1005 Short - - -

FB4 1005 Short - - -

FB5 1005 Short - - -

FB6 1005 Short - - -

7/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Board layout

Evaluation board PCB information

Material FR-4

Board thickness 1.6mm

Copper thickness 1 oz

Number of layers 4

Board size 60X80mm

Minimum copper width 0.15mm

Minimum air gap 0.15mm

Minimum hole size 0.3mm

The layout of REFLED003-EVK-003 is shown below.

(Top view)

Figure 7. Top layer layout

(Top view)

Figure 8. 2nd layer layout

(Top view)

Figure 9. 3rd layer layout

(Top view)

Figure 10. Bottom layer layout

(Top view)

8/9

Sep.2023

User’s Guide

REFLED003-EVK-003

Reference application data

(Ta=25°C, Output voltage=25.3V, Iout=125mA x 6ch)

Figure 11. Efficiency vs Input voltage

Figure 12. Gain, Phase vs Frequency (VCC=13.5V)

100

5101520

Efficiency (%)

Input voltage (V)

-180

-120

-60

120

180

-60

-45

-30

-15

100 1000 10000 100000 1000000

Phase(deg)

Gain(dB)

Frequency(Hz)

Gail

Phase

Altri manuali per BD82A26MUF-M

Indice

Altri manuali Rohm Scheda madre

Rohm

Rohm WPC Qi-compliant Wireless Power Series Manuale utente

Rohm

Rohm BM1Z002FJ Manuale utente

Rohm

Rohm HB2637L-EVK-301 Manuale utente

Rohm

Rohm BM3G007MUV-EVK-003 Manuale utente

Rohm

Rohm BM92A56MWV-EVK-001 Manuale utente

Rohm

Rohm Switching Regulator Series Manuale utente

Rohm

Rohm KX134-1211-EVK-001 Manuale utente

Rohm

Rohm BM2P0161-EVK-003 Manuale utente

Rohm

Rohm BD868x0-EVK-302 Manuale utente

Rohm

Rohm Switching Regulator Series Manuale utente

Rohm

Rohm TPPFCSIC-EVK-301 Manuale utente

Rohm

Rohm BD9E201FP4-Z Manuale utente

Rohm

Rohm BM1Z002FJ Manuale utente

Rohm

Rohm BD63800MUF-EVK-001 Manuale utente

Rohm

Rohm Lapis Technology RB-D610Q327TB48 Manuale utente

Rohm

Rohm BM2P141X Manuale utente

Rohm

Rohm BD7682FJ-LB-EVK-302 Manuale utente

Rohm

Rohm BM92A56MWV-EVK-001 Guida rapida

Rohm

Rohm BM92A56MWV-ZE2 Manuale utente

Rohm

Rohm Switching Regulator Series Manuale utente

Rohm

Rohm BM1422AGMV-EVK-001 Manuale utente

Rohm

Rohm Shield-EVK-001 Manuale utente

Rohm

Rohm BM3G007MUV-EVK-002 Manuale utente

Rohm

Rohm BD82A26MUF-M Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente