Roland CammJet CJ-500 Manuale utente

Refer to yourCAMMJET / Hi-Fi JET user’s manual for detailed instructions on working with the unit.

Quick Start Guide

Unpacking

Begin by unpacking the stand. Instructions are included in the box. Then prepare the main unit and install

on stand. Make sure that the unit is firmly attached to the stand before proceeding. Ink waste tank

assembly is recommended next.

Powering on

The main display will prompt you to select an ink type and press ENTER.

Turn ON the main power first

Then turn ON secondary power.

Roland CJ-500 Or Roland Hi-Fi JET

Ver.1.00

Roland CJ-500

UNKNOWN INK TYPE

SELECT INK TYPE

PIG.CMYKLcLm

INSTALL

DRAIN TANK

NOW FILLING INK

Use the [ ] [ ] key to select the installed ink type

and press the [ENTER] key.

No ink is filled.

Attach the drain tank, and

press the [ENTER] key.

The system will execute ink fill.

This operation takes several minutes.

PIG. CMYKLcLm/PIG. CMYKOrGr/DYE CMYKLcLm

Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.

Pass the material between the pinch rollers and the grit

rollers as shown in the figure.

Move the sheet loading lever toward LOAD.

The pinch rollers lower to hold the material in place.

3Close the front cover.

Use the [ ] and [ ] keys to select [Piece], then

press the [ENTER] key.

Sheet loading lever

Loading Flat Material

Refer to steps 5 and 6 in "Loading Roll Material," and

position the material and the pinch rollers correctly.

Press the [SETUP] key. This detects the width and

length of the material and shows the printable width

and length on the display.

5Note for CAMMJET: If a pinch roller is positioned over an

area where there is no grit roller, the message shown at below

appears when you press the [SETUP] key.

PINCHROLL ERROR

INVALID LEFTPOS

or [RIGHT]

Top menu

W1000mm L1230mm

FINE BI-DIR

*If the material is misaligned and looks like it might

come loose from the pinch rollers, or actually does

come loose, please reload the material.

Setup for Printing

Check the positioning of the pinch rollers and

make sure they are aligned at the correct positions.

The SETUP LED lights up

SETUP SHEET

ROLL EDGE PIECE

Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.

Head test print

Before starting to print, perform the Head Test Print to check the state of the head.

Missing dots may reduce the printing quality. On the CAMMJET simply press [Print Test]. On the FJ:

If there are any missing dots or other evidence of a drop in printing quality, clean the head (see

User’s Manual section concerning "Cleaning the Printing Heads").

Head Height Adjustment

The CAMMJET have 3 settings for head height: 1.1mm, 1.6mm & 2.1mm clearance to accommodate different

thicknesses of material. (Max 1.5mm) Make sure to select the appropriate height adjustment before printing.

Height of the printing head

High

Low

Printing Mode

PHOTO:This is suitable for printing photographs.

SUPER: This is suitable for output with high image

quality, such as posters.

FINE: This is suitable for output with comparatively

high detail, such as posters.

FINE2:This is suitable for outputting posters and the

(Factorylike on various materials. [CAMMJET ONLY]

default)

NORMAL: This is suitable for printing large-size items

with comparatively high quality in a short

time.

FAST: This is suitable for printing large-size items in

a short time.

DRAFT: This can produce output in the shortest time. It

is suitable for checking layout and the like.

UNI-DIRECTION:

Uni-directional printing.

Printing is performed as the carriage moves from right to left.

Printing quality is better than with [BI-DIRECTION].

BI-DIRECTION (factory default):

Bi-directional printing.

Printing is performed as the carriage moves from right to left,

and also as it returns from left to right.

Printing speed is faster than with [UNI-DIRECTION].

Printing Direction

Press the [ ] key to make the setting for the printing

direction.

Use the [ ] and [ ] keys to display the printing

direction, then press the [ENTER] key.

DIRECTION

BI-DIRECTION

Press the [PRINTCONFIG] or [PRINT QUALITY] key.

1Use the [ ] and [ ] keys to choose the printing

mode.

PRINT MODE

FINE

Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.

Demo Print

Go to the Demo Print menu and press enter. Six squares will print and cut confirming proper setup

Quick-Start Complete

The CAMMJET or Hi-F JET is now ready to print. Refer to the User’s manual on connecting to your computer, software

installation. An ECP printer cable is included in the accessories kit, which requires ECP settings on an

LPT port. Refer to your computer manufacturer’s instructions on setting a parallel port to ECP.

Install a blade and load a material, then close the front

cover.

1Use the [ ] , [ ] , [ ] and [ ] keys to move

the tool carriage to the place where the test cutting is

to be performed.

Press the [TEST CUT] key for 1 second or longer.

Test cutting starts.

Examine the cutting results for the material and diagnose the cutting conditions.

4(1) Peel off the round section (marked by ).

When it can be peeled by itself, without disturbing the square (marked by ), the

cutter force is set appropriately.

If it peels, either the “blade force” or the “amount of blade extension” is insufficient.

(2) Remove the square section (marked by ).

The optimum blade pressure is correct if you can clearly make out the lines left by the

blade.

If the blade trace is indistinct or too strong, you need to adjust the “blade force” or the

“amount of blade extension.”

(3) Check the shape of the rectangle.

- If the corners are cut securely as shown in A, there conditions are correct.

- If the corners are rounded as shown in B, the “blade offset” is insufficient.

- If the corners have “horns” as shown in C, the “blade offset” is too large

ABC

Setup for Cutting

Altri manuali per CammJet CJ-500

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Roland Stampante

Roland

Roland ColorCamm PC-12 Manuale utente

Roland

Roland FJ-500 Manuale utente

Roland

Roland VersaUV LEF2-300 Manuale utente

Roland

Roland TrueVIS SG3-540 Manuale utente

Roland

Roland VersaSTUDIO BN-20D Manuale utente

Roland

Roland Texart RT-640 Manuale utente

Roland

Roland VS-640i Manuale operativo

Roland

Roland Advanced Jet AJ-1000i Manuale utente

Roland

Roland LEC-300A Manuale utente

Roland

Roland SOLJET PROIII DU-740 Manuale utente

Roland

Roland IU-1000F Manuale utente

Roland

Roland GX-640/GX-500/GX-400/GX-300 Manuale utente

Roland

Roland Texart RT-640 Manuale utente

Roland

Roland VersaUV LEC2-640 Manuale operativo

Roland

Roland HB-12 Manuale utente

Roland

Roland TrueVIS SG3-540 Manuale utente

Roland

Roland XF-640 Manuale operativo

Roland

Roland SP-540i Manuale utente

Roland

Roland METAZA MPX-70 Manuale utente

Roland

Roland SolJet PROII SC-540 Manuale utente

Roland

Roland FLATJET FLJ-300 Manuale utente

Roland

Roland XC-540MT Manuale utente

Roland

Roland Metaza MPX-50 Manuale utente

Roland

Roland Metaza MPX-60 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente