Roland ColorCAMM PRO PC-600 Manuale di istruzioni
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
ColorCAMM PRO PC-600
Frequently Asked Questions
My output is grainy and has dot-like specs and streaks. How can I fix this?
How do I print with Spot Colors?
My output is printing with lines through the center of my image; it looks like a
horizontal space or a gap across the image. How can I fix this?
Why does my ColorCAMM PRO PC-600 material begin to skew (travel or shift)
from left to right after it has cut 1 or 2 feet?
Why are my circles or certain letters not meeting (coming together to form a
complete circle) at the end of the cut line?
Which port do you recommend I select for my ColorCAMM PRO PC-60?
Why is the blade cutting deep in some areas and not in others? My
ColorCAMM PRO PC-60 is cutting jagged and jumps.
What is the average blade life?
What should I do when the Cartridge Holder LED #1 is flashing?
What should I do when the Piece LED and Roll LED blink simultaneously?
What should I do when the Roll LED is flashing?
Can my PC-600 pull vinyl directly off a Roll?
1. My output is grainy and has dot-like specs and streaks. How can I fix this?
Make sure to use clean vinyl and keep the platen, which is a very thin metal
strip below the print head towards the right side, clean. Use a soft dry cloth to
clean the vinyl or you may use a denatured alcohol cleaning solution like
Isopropyl. Do not use the cleaning sheet to clean the print head more than
twice in one cleaning. The cleaning pen should be used to clean underneath
the head. The platen should be wiped with the cleaning pen. If the ribbon
cartridge went over the platen and laid down color, this could cause streaks to
print. Make sure to keep the platen clean and free from dust and dirt.
2. How do I print with Spot Colors?
In the properties of the driver at the Output Option
tab, select the color you want
to use as your spot color under Special Colors . For example, if you select Red,
make sure in the software color palette you chose RGB 255 Red . Turn 'OFF'
the process color dialogs by deselecting this option.
3. My output is printing with lines through the center of my image; it looks
like a horizontal space or a gap across the image. How can I fix this?
Do a 'Line Pitch Adjustment '. There is a Narrow and Extra Narrow adjustment
correction that can be made. The PC-60 User Manual has step by step
instructions on how this is done.
4. Why does my ColorCAMM Pro PC-60 material begin to skew (travel or
shift) from left to right after it has cut 1 or 2 feet?
You may need to replace the Pinch Rollers. The pinch rollers will get worn
down easily if they are left down on the cutter over-night. Always leave the
pinch rollers in the up position when the cutter is not in use.
5. Why are my circles or certain letters not meeting (coming together to
form a complete circle) at the end of the cut line?
When using 2 or 3 mil vinyl, the machine Offset should be 0.25mm. When
using Heat Transfer or Sandblast Resist type material, use a 60 degree blade,
slow down the cut speed and, depending on the type of material, the offset
may need to be set at 0.5mm. You should also check the communication
settings to make sure your software is configured with the recommended
settings for the type of connection that you are using: serial or parallel.
6. Which port do you recommend I select for my ColorCAMM PRO PC-60
Parallel port. We do not recommend sharing multiple printers or switchboxes
on the same port.
7. Why is the blade cutting deep in some areas and not in others? My
ColorCAMM PRO PC-60 is cutting jagged and jumps.
Check to see if the cutter protection strip needs to be replaced. If it is worn,
dented or cut up it needs to be replaced. If the cutter protection strip is not
damaged, check the position of the blade in the blade holder. Make sure the
blade holder is tightened around the blade.
8. What is the average blade life?
The life of a blade varies depending on the amount of cutting it performs. The
total cutting length can vary considerably depending on the thickness,
toughness and type of adhesive of the cut material. Setting an appropriate
cutter force, one that is well matched to the material and the hardness of the
blade, can extend the life of the blade.
9. What should I do when the Cartridge Holder LED #1 is flashing?
The ink ribbon may be empty or incorrectly positioned in the print head. Either
replace the ribbon cartridge with a new one or position it correctly.
10. What should I do when the Piece LED and Roll LED blink
simultaneously?
Make sure the pinch rollers are in the proper position and make sure the eye
sensors are covered by material.
11. What should I do when the Roll LED is flashing?
Lower the sheet loading lever to secure the material in place.
12. Can my PC-60 pull vinyl directly off a Roll?
The ColorCAMM PRO PC-60 is not designed to pull heavy rolls of vinyl or
material. Please roll out the appropriate amount of material you are going to be
using for your current job.
Altri manuali per ColorCAMM PRO PC-600
1
Indice
Altri manuali Roland Stampante
Roland
Roland Texart RT-640 Manuale utente
Roland
Roland VersaCAMM SP-300S Manuale utente
Roland
Roland PC-600 Manuale utente
Roland
Roland LEC-300A Manuale utente
Roland
Roland SolJet PROII SC-540 Manuale utente
Roland
Roland TrueVIS SG2-640 Manuale operativo e di manutenzione
Roland
Roland METAZA MPX-70 Manuale utente
Roland
Roland VersaCAMM ECO-SOL MAX3 Manuale utente
Roland
Roland VersaStudio BR-20 Manuale per l'uso e la cura
Roland
Roland VersaUV LEF2-300 Manuale operativo e di manutenzione
Roland
Roland TrueVIS VG-640 Manuale utente
Roland
Roland SOLJET PRO4 XF-640 Manuale utente
Roland
Roland VersaUV LEF2-300 Manuale utente
Roland
Roland VersaSTUDIO BN-20A Manuale utente
Roland
Roland VersaUV LEF-12 Manuale utente
Roland
Roland VersaSTUDIO BN-20D Manuale utente
Roland
Roland SOLJET PROIII XC-540 Manuale utente
Roland
Roland VersaUV LEF2-300 Manuale utente
Roland
Roland SOLJET SC-500 Manuale utente
Roland
Roland VersaUV LEF2-300 Manuale utente
