Rollerdor RD20X2 Manuale utente

Rollerdor RD20X2 Control Box, Edition 2022/1

RD20X2 Control Box

Installation Guide for Roller Garage Doors

Edition 2022/1

Rollerdor RD20X2 Control Box, Edition 2022/1

1. INSTALLING RECEIVER BOX

1 Open the lid of the receiver box by unscrewing the four

screws (one in each corner) (fig.1).

2 Remove the two screws from the bottom of the box (these

can be found behind the glands) and the wall mounting

plate can be removed from the back

(fig.2 & fig.3).

3 Making sure the fixing plate is square with the screw

fixings at the bottom, mark the four fixings points. This

should be at a comfortable height to operate the push

buttons but out of the easy reach of children

- between 1500mm from the floor and 300mm down from

the roof/ceiling is recommended. Drill and then secure in

place (fig.4).

4 Hook the top of the receiver box on to the wall fixing plate

with the cable glands pointing downwards and secure

with the two screws.

5 If you have a safety brake with a cable then run the two

core cable from the safety brake end across to the same

end as the receiver box, making sure to securely fix the

cable out of the way of the working mechanism.

6 Remove the green 5 terminal block in the bottom left

corner (fig.5) and you will see letters printed on the

circuit board.

7 Wiring as follows:

Mains Power:

N– Neutral / Blue 3 core cable (power)

L– Live / Brown 3 core cable (power)

Earth – connect power cable directly to earth from

motor in plastic connector.

Motor:

U– Brown 4 core cable (motor)

V– Black 4 core cable (motor)

Earth - connect motor cable directly to earth from

motor in plastic connector.

W[c] – Blue 4 core cable (motor)

Safety Brake:

Remove black link wire from far right hand side stop

terminal, and replace with Brown (2 core cable) and

Blue (2 core cable), one each side (fig.5).

fig.1

fig.2

fig.3

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

1 Press and hold the bottom close button on the receiver board (fig.5). This is located at the bottom

right corner of the yellow transformer and the barrel should start turning in the downwards

direction. Should the barrel be turning in the upward direction, swap motor

wires black to U and brown to V.

DIRECTION OF ROTATION

fig.5

fig.4

8 Before plugging in, check to make sure that there

are no bare cables touching and all wires are

securely fixed.

9 There is a four dipswitch block at the bottom

middle of the receiver board (usually blue or red).

Slide dipswitch 2 into the up position (fig.5).

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

2. SETTING UP WIRELESS

SAFETY EDGE KIT

(RD20X2 OPTICAL SAFETY EDGE)

PROGRAMMING BASE RAIL UNIT

1 The control box is currently in hold to run

operation for open and close, if the limits

of the motor have not been set then please

use the open and close buttons that can be

found at the bottom right corner of the yellow

transformer (Fig.6) to set these limits..

2 Once installation is complete, slide back down

dip switch ‘2’ in the control panel, this can

be found on the four dipswitch block at the

bottom middle of the receiver board (usually

blue or red) (fig.6).

3 For access to the base rail unit on the right side

(where the writing is), push at the end of the

grey cover and slide to the left. This will give

access to the board (fig.7).

4 Remove the plastic tab from the batteries and

the LEDs will blink on the safety edge unit.

5 Inside the receiver box press and hold the

“PROG” button on the receiver card (this is the

card plugged onto the board) until you hear a

single beep (fig.9), then within 5 seconds press

and hold the “PROG” button on the wireless

safety edge (fig.8) and you will hear another

beep from the receiver box.

6 Wait several seconds until you hear 2 beeps

from the receiver box and pairing is complete.

fig.6

PUSH

GREY

SECTION

PUSH

GREY

SECTION

fig.7

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

PROGRAMMING RUN TIMERS & LIMITS

1 The curtain must be all the way down in the closed position

before starting.

2 Press and hold the white “PROG” button on the main

receiver board for 2 seconds until the red LED lights up

and stays on, this is next to the start button (fig.10).

3 Press & release the “START” button (next to “PROG”

button) (fig.10) the receiver box will now start a setup

process.

4 Run timer setup is complete.

Please be aware! During set up the

motor may reach thermal cut out.

If this occurs you will need to wind

the curtain down manually to allow air

to pass over the barrel and cool.

This can take up to 45 mins.

If the curtain stops (due to thermal cut

out), or once completed the error light

is on or flashing, then you will need to

clear the memory of the base rail unit

and handsets before restarting the

whole procedure (refer to page 7

to clear memory).

fig.9

fig.8

fig.10

The curtain will open slightly and close again.

The curtain will then open and fully stop.

Press & release the "START" button again

(fig.10) and the curtain will close fully.

Wait for several seconds and the "PROG" light

will turn off.

(1)

(2)

(3)

(4)

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

1 Press and hold the “RADIO PROG” button

(fig.11A). You will hear a beep and the red

LED alongside “C1” will illuminated (fig.11B).

Then release the “RADIO PROG” button.

2 Press top button on handset (fig.11A).

The panel will beep to confirm it has accepted.

Repeat for all other handsets.

3 Leave for several seconds and the receiver box

will beep twice to confirm end of programming.

SEQUENTIAL OPERATION

1 Press and hold the “RADIO PROG” button

(fig.11A) until you hear 3 beeps and the red LED

alongside “C3” will illuminate then release the

button.

2 Press top button on handset (fig.12A).

The panel will beep to confirm it has accepted.

Repeat for all other handsets.

3 Leave for several seconds and the receiver box

will beep twice to confirm end of programming.

4 Press and hold the “RADIO PROG” button

(fig.11A) until you hear 4 beeps and the red LED

alongside “C4” will illuminate then release the

button.

5 Press bottom button on handset (fig.12B).

The panel will beep to confirm it has accepted.

Repeat for all other handsets.

6 Leave for several seconds and the receiver box

will beep twice to confirm end of programming.

INDEPENDENT BUTTON OPERATION

fig.12

3. PROGRAMMING OF REMOTE

CONTROL HANDSETS

fig.11

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

To clear memory you will need a small screwdriver. fig.13

1 Press and hold the “RADIO PROG” button (fig.13).

You will hear a beep and the red LED alongside “C1”

will illuminate.

2 Insert screwdriver between the 2 pin terminals on

the board (MR) to bridge between them (fig.13).

3 Press and hold the “RADIO PROG” button (fig.13).

The panel will beep 8 times and then go into 1

continuous beep. As soon as you hear this, release

“RADIO PROG” button and then remove screwdriver

from terminals and board will stop beeping.

4 Leave for several seconds and the receiver box will

beep twice to confirm end of programming.

CLEARING MEMORY OF REMOTE CONTROL

HANDSETS

fig.14

1 Press and hold the “PROG” button (fig.14A) on

the receiver card (this is the card plugged onto the

board) until you hear a single beep.

2 Insert screwdriver between the 2 terminals on

the board (forks below “PROG” button) to bridge

between them (fig.14B).

3 Press and hold the “PROG” button, the panel will

beep 8 times and then go into 1 continuous beep.

As soon as you hear this release “PROG” button and

then remove screwdriver from terminals and board

will stop beeping.

4 Leave for several seconds and the receiver box will

beep twice to confirm end of programming.

To clear memory you will need a small screwdriver.

CLEARING MEMORY OF BASE RAIL UNIT

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

WIRING AS FOLLOWS:

Receiver Box Green 6 Block Terminal (fig.15):

L0 – Up wire from switch

L2 – Down wire from switch

L1 – Common wire for the supply to the switch

L1 – L3 Link wire between terminals

Rocker Switch (fig.16):

4– Up wire

3– Down wire

5– Common wire for the supply to the switch

Fit Link wire from 5 to 2

To open rocker switch remove screws

Key Switch (fig.17):

Right Block 13 – Up wire

Left Block 14 – Down wire

Right Block 14 – Common wire for the supply to the switch

Left Block 13 – Right Block 14 Link wire between terminals

To open key switch remove screw then turn key

a quarter turn.

HARD WIRED ROCKER / KEY SWITCH

fig.17Bfig.17A

4. OPTIONAL EXTRAS

fig.16

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

fig.15

Link wire

Up wire

Down wire

Common wire

Rollerdor RD20X2 Control Box, Edition 2022/1

WIRELESS KEY PAD

INSTALLATION

Fit directly to the wall using the 2 fixings making sure it is level and square with the writing at the bottom.

1 Press and hold the “RADIO PROG” button

(fig.15A). You will hear a beep and the red LED

alongside “C1” (fig.15B) will illuminate, then

release the “RADIO PROG” button.

2 Enter the access code and press OK (fig.18B).

The panel will beep to confirm it has accepted

the unit.

3 Leave for several seconds and the receiver

box will beep twice to confirm end of

programming.

PROGRAMMING TO RECEIVER BOX

fig.18

PROGRAMMING CODES

Master Code:

1 Press and hold the * button (fig.18A). For 3

seconds until the LED issues a slow red

flashing light.

2 Enter the master code (factory issue 12345678)

and press OK (fig.18B). The red LED will

flash faster.

3 Press the * button (fig.18A) then enter the new

master code followed by the * button. The LED

will flash green.

4 Enter the new master code again followed by

the * button (fig.18A). The LED will have

a permanent green light for 2 seconds then go

out. This means it has been programmed. If the

second entry doesn’t match the first, the LED

will flash red and it has not been programmed.

1 Press and hold the * button (fig.18A) for

3 seconds until the LED issues a slow red

flashing light.

2 Enter the master code and press OK

(fig.18B). The red LED will flash faster.

3 Enter your new access code (1 to 8 numbers

long) followed by the channel number from

1 to 4 (e.g. 5555 is the number and 1 for the

channel so 55551) and press OK (fig.18B).

4 The LED will have a permanent green light

for 2 seconds then go out. This means it has

been programmed. If you wish for more than

1 access code, then it must be programmed

to a separate channel otherwise it will just

replace the already stored code.

Access Code

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required.

Rollerdor RD20X2 Control Box, Edition 2022/1

Rollerdor Ltd

10 & 12 Jarrold Way

Bowthorpe Employment Area

Norwich

Norfolk NR5 9JD

+44 (0)1603 743215

sales@rollerdor.net

www.rollerdor.net

Company Registration Number. 10676267

Registered Oice Address:

Rollerdor Ltd, Bankside 300 Peachman Way,

Broadland Business Park, Norwich,

Norfolk, United Kingdom, NR7 0LB

Edition 2022/1

Indice

Altri manuali Rollerdor Unità di controllo

Rollerdor

Rollerdor RD1X2 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente