Ross SideBox Manuale

SideBox Installation and

Setup

Installation

SideBox can be installed onto a desk, into the desk using

the supplied Desk Mounting Brackets, or onto a standard

VESA mount.

Desk Mounting

SideBox can be mounted into a desk in either a ﬂat or

sloped position. How you want SideBox to be positioned

determines where the Desk Mount Brackets are

installed.

Figure 1: In-Desk Mounting Options

If you are sitting SideBox onto a desk you do not need

to install the Desk Mounting Brackets.

Desk Cutout

The desk cutout size for SideBox is the same if you are

mounting SideBox in the ﬂat or sloped position.

Figure 2: Desk Cutout Size

To Install the In-Desk Mounting Brackets

1. Select the mounting option you want to use for

how SideBox is installed.

2. Remove the mounting screws from the side of

SideBox for the mounting option you have

chosen.

Figure 3: Mounting Screws

3. Install the Desk Mounting Bracket onto the

side of SideBox using the screws you just

removed.

Figure 4: Mounting Bracket)

4. Repeat this procedure for the other side of

SideBox.

VESA Mounting

The SideBox can be mounted onto aVESA FDMI MIS-D

75 or 50, C Mounting Arm.

Figure 5:VESA Mounting Holes

Cabling

Each SideBox has connectors for primary (PS1), and

secondary (PS2) power supply, and two RJ-45

communications ports (PREV and NEXT).

Figure 6: SideBox Cable Connections

Note: A maximum of 14 SideBoxes can be daisy-chained

together off of a single External Link Port onVision.A maximum

of 8 SideBoxes can be daisy-chained together on Carbonite.

4802DR-304-01

To Cable SideBox

Caution: Always connect the 12V DC Power Supply to the

SideBox before connecting the AC mains power.Connecting

the power supply to the AC mains power before connecting to

the SideBox could damage the SideBox.

1. Connect and secure one end of the Control

Cable to the External Link port 2, 3, or 4 on

Vision, or the NEXT port on Carbonite or

another external module already connected to

the control panel.

2. Connect and secure the other end of the Control

Cable to the PREV port on the SideBox.

3. Connect and secure one 12V DC Power Supply

to the PS1 connector on the back of the SideBox.

SideBox Setup

Setting Up SideBox with Vision

To set up communications between the Vision control

panel and SideBox, you must do the following:

•Set the External Link port (L2, L3, L4) that you

connected to SideBox to External Module (Ext

Module).

• Assign the SideBox to a panel row.

Refer to your Vision Engineering Manual for information

on assigning the SideBox to an external link port, and

assigning the SideBox to a panel row.

LCD Contrast

If the module installed in the SideBox has an LCD

display, such as mnemonics, the contrast of this display

must be adjusted manually using a Phillips screwdriver.

Figure 7: Contrast Adjustment

Replacing a Module

Important: Contact Ross VideoTechnical Support before

attempting to replace a module with a different type of module

in a SideBox.

To Remove a Module

1. Disconnect all power and communications cables

connected to SideBox.

2. Remove the 14 screws from the front, back, and

sides of the SideBox.

Figure 8: Removing Screws

3. Slowly lift the SideBox Top out of the SideBox

Base until you can access the internal cables.

4. Disconnect both of the Module Control Link

Cables and the Power Cable from the module.

Figure 9: Disconnecting Internal Cables

5. Remove the 4 retaining nuts that secure the

module onto the Module Mounting Plate.

Figure 10: Removing Module

Altri manuali Ross Unità di controllo

Ross

Ross M35 Series Manuale utente

Ross

Ross DM2 C Series Manuale utente

Ross

Ross M35 Series Guida rapida alla configurazione

Ross

Ross CrossMirror CM26 Series Manuale utente

Ross

Ross DM1E Manuale utente

Ross

Ross openGear FSR-6201 Manuale utente

Ross

Ross RSe Series Guida rapida alla configurazione

Ross

Ross Vision Audio Control Manuale

Ross

Ross W65 Series Manuale utente

Ross

Ross Vision 4800DR-332-02 Manuale utente

Ross

Ross RSe Series Guida rapida alla configurazione

Ross

Ross RSe Series Manuale utente

Ross

Ross M35 Series Manuale utente

Ross

Ross DM1 C Manuale utente

Ross

Ross SV27 Series Manuale utente

Ross

Ross Vision Crosspoint Module Manuale utente

Ross

Ross 21 Series Manuale utente

Ross

Ross Serpar 35 Series Manuale utente

Ross

Ross M DM2 C Series Manuale utente

Ross

Ross Vision 4800DR-324-02 Manuale utente

Ross

Ross GearLite MUX-9258-A Manuale utente

Ross

Ross RSe Series Manuale utente

Ross

Ross W74 Series Manuale utente

Ross

Ross CrossMirror 77 Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente