Saitek CF5 Series Manuale utente

Serie

< Automatic burner control unit >

MONO – DOUBLE ELECTRODE / UV-SENSOR FLAME DETECTION

SAITEK srl

www.saitek.it [email protected]

Casalgrande (RE) ITALY Tel . +39 0522 848211 Fax +39 0522 849070

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.

AUTOMATIC BURNER CONTROL UNIT

C F

5SERIES

MONO – DOUBLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

NOTES .

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.04-2018

BURNER FLAME CONTROL

C F

5SERIES

page 1 di 5

DOUBLE / SINGLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

INSTRUCTIONS FOR USE .

Read carefully and preserve this use and

maintenance reference manual.

CONFORMIT .

The manufacturer declares that:

- The CF5has been designed, realized

and tested in compliance with the

European Rule EN298 relative to

“Control and safety automatic systems

for gas burners and gas appliances

with or without fan.

- The CF5is conform to the essential

requirements provided for by

Directive 90/396/EEC for gas

applications (E.D. 90/396/EEC art. 1

paragraph 2).

Classification according to EN 298:

B M R L X N

APPLICATIONS .

The CF5flame control appliance directly

lights and controls intermittent gas

burners, or rather burners that shall be

turned off at least once in the 24 hours.

The burner is checked by an ionization

electrode.

For grounded grids.

With a single restart due to flame put out.

The CF5can be applied directly to the

burner in industrial thermal processes for

metals, glass, ceramic, plastic, chemical,

etc...., where there is no need of a pre-

ventilation before turning it on.

Besides it can be applied on atmospheric

burners for general heating.

ATTENTION

Avoid presence of condensation inside

the box and on the card surface..

TECHNICAL SPECIFICATIONS .

- Data relating to power supply

characteristics (V ~ / Hz / W), working

temperature (° C), IP protection class,

discharge time (Ig T), safety (Sc) and

detection threshold ( Sens.), See the

applied label.

- Voltage supplied to the loads the

same to the supply voltage.

- Detection with 2 electrodes, 1

electrode or UV lamp

- Possibility of using both electronic

and traditional ignition transformers.

- LED display: on, block, discharge and

detection.

- Alarm contact in exchange: closed

when in block, closed when in flame

detection.

ATTENTION!!!

Any indication and operation

indicated in the present manual

shall be carried out only by

authorized and qualified personnel

in charge.

Improper and in

correct assembly,

adjustment, modification, use or

maintenance can cause serious

damages and accidents to persons

and things.

Read carefully the instructions

before installing the appliance. The

assembly shall be in compliance

with the regulations in force.

In order to prevent accidental

electrocutions it is recommended

you disconnect the electric current

before opening the appliance.

Before supplying power check the

value reported on the tag.

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.04-2018

BURNER FLAME CONTROL

C F

5SERIES

page 2 di 5

DOUBLE / SINGLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

SCHEDA VISUALIZZATRICE .

The CF5 flame control is supplied

together with the additional display card

STK035. This offers the opportunity to

control the functionality of the equipment

in a more effective and immediate way.

This is made possible by the four LEDs for

displaying the flame level, the LED for

controlling the safety systems and the

LED for remote unlocking. The latter also

remains slightly lit when the main switch is

in position 0 to indicate presence of

voltage (N.B. can only be used by

authorized personnel keeping under

control the burner to be turned on).

MONTAGGIO .

-Mounting position as desired

-Assembly of the fixed rear part,

through 4 preformed holes to be

removed by pressure.

- Prepared for pipe connection collars

- CF5 can be supplied already wired,

otherwise make the necessary holes

only in the rear part and use cable

glands that guarantee at least the

same degree of IP protection declared.

CAVI CONSIGLIATI .

IONIZATION: Maximum length 10 meters with

recommended section 1 mm. Laying away from

sources of disturbance, avoid external electrical

influences.

IGNITION: as specified by the manufacturer of the

ignition transformer. Recommended conductor

diameter 1mm. Lay individually away from metal

parts.

CABLAGGIO .

Remove power from the system.

In three-phase systems, use the same phase on

the inputs. There must be no voltage present in the

output for the solenoid valve.

The enabling command of the CF5 that comes

from the safety sequence (all the main control

devices for safety purposes such as thermostats,

GASmin, GASmax, leakage control, prewash, etc.

...) must be voltage-free contacts.

The output voltage for the solenoid valve and the

ignition transformer (included if required) is the

same as the supply voltage.

The current max. for solenoid valve and ignition

transformer is 1A.

Alarm contacts max 1A 230Vac not protected by

internal fuse.

Make a good connection of the ground of CF5 to

the burner mass to ensure correct operation.

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.04-2018

BURNER FLAME CONTROL

C F

5SERIES

page 3 di 5

DOUBLE / SINGLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

Partenza normale con fiamma

Riavvio dopo mancanza fiamma

MESSA IN SERVIZIO .

1. Open the gas valve.

2. Start the system.

3. Give power to the CF5.

4. Press the power button (green power

LED lights up).

5. Switch on the enable terminal to start

the ignition cycle.

6. Waiting time at the start of about 5sec.

7. After this time the CF5 will carry out the

ignition cycle. The gas solenoid valve

will be commanded and the discharge

will be carried out at the same time

(yellow discharge LED will light up). At

the end of the discharge the presence

of the flame will be checked.

8. In its presence, the equipment goes

into operation by turning on the green

detection LED and continuing to power

the solenoid Gas valve.

9. Otherwise CF5 will go into lockout (the

gas solenoid valve will be

disconnected, the alarm contact will

close and the red lock LED will light

up). To reset it and retry the boot it will

be necessary to switch it off and switch

it on again using the power button.

N.B. The terminl box should never be

used. This clamp has remote unlocking

functionality and must be used only by

authorized personnel, keeping the burner to be

re-ignited under strict control.

OPERATION CHECK .

1. Remove the detection plug during

operation.

2. CF5 will attempt to restart only once,

after which it will be shut down due to

an anomaly (the gas solenoid valve

will be disconnected, the alarm contact

will close and the red LED will light

up).

3. The burner flame must go out.

4. If a different operation should occur

check the wiring. This done if the

problem has not been resolved

disassemble the CF5 and send it to the

manufacturer for a complete overhaul.

After replacing the safety device, check its

operation:

- Close the general gas valve and check

that the appliance, after a few attempts,

does not start.

If the safety device works correctly and

the wiring is in order but the equipment

attempts to start the burner, send it to the

manufacturer for a check.

OPERATING MODES GRAPHS .

Ta => waiting time before starting

(pre-purge Time)

Start without flame

Start with flame

Re- start after flame faliure.

Partenza senza fiamma

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.04-2018

BURNER FLAME CONTROL

C F

5SERIES

page 4 di 5

DOUBLE / SINGLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

1 2

34 5 678

1 2

34 5 678

1 2

34 5 678

1 2

3 4 5 6 7 8

On CF5 it is possible to set some

functions and some values through 8

microswitches housed on the on-board

electronic board.

The basic configuration of

microswitches is all 0

TIMES SETTINGS .

Pre Purge Time setting

Pre Purge 5 sec

Pre Purge 1 sec

Pre Purge 8 sec

Pre Purge 10 sec

Pre Purge 20 sec

Pre Purge 30 sec

1 2

34 5 678

Pre Purge 50 sec

1 2

34 5 67 8

Pre Purge 70 sec

1 2

3 4 5 6 7 8

Ignition Time setting

Ignition Time 5 sec

1 2

34 5 67 8

Ignition Time 12 sec

1 2

3 4 5 67 8

Safety Time loss of Flame

Safety Time 2 sec

1 2

3 4 5 6 7 8

Safety Time 3 sec

1 2

3 4 5 6 7 8

FUNCTIONS SETTINGS .

Attempt to re-ignite after loss of flame

Yes

Ignition/re-ignitio attemps numbers

N° 1

N° 3

Detection flame circuit 24h self check

Enabled

1 2

3 4 5 6 7 8

Disabled

1 2

3 4 5 6 7 8

Self check OK

Self check No flame detection

1 2

34 5 678

1 2

34 5 678

1 2

3 4 5 6 7 8

1 2

3 4 5 678

1 2

3 4 5 6 7 8

1 2

3 4 5 6 7 8

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.04-2018

BURNER FLAME CONTROL

C F

5SERIES

page 5 di 5

DOUBLE / SINGLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

RETIFICATION OF FAULTS .

? < TROUBLE>

! <CAUSE >

* <REMEDY>

? THE IGNITION SPARK DOES NOT

APPEAR.

! The distance between the electrode and

the burner body is too great.

* Set a distance of max. 2 mm.

! The igniter cable does not make contact

with the pipe.

* re-screw the pipe tightly.

! The igniter cable has a leakage on the

earth.

* Check the laying of the cable, clean the

ignition electrode.

! The ignition voltage is too low.

* use an ignition transformer with power >

5 KV

! The ignition cable is too long.

* Shorten its length to 1 m. (max. 5 m.)

! The igniter cable does not make contact.

* Screw it tightly on the ignition

transformer.

? THE GAS DOES NOT REACH IT

! The gas solenoid valve does not open

* Check the solenoid valve connection.

! There is still presence of air in the gas

hosepipe.

* Make many ignition attempts in order to

fill completely the gas hosepipe.

? THE GAS DOES NOT REACH IT

AND THE IGNITION SPARK DOES

NOT APPEAR, THE CF3 DOES NOT

START.

! Short circuit in the ignition or in the

solenoid valve outlet.

* Check the wiring

- in case of short circuit in outlets

eliminate it and change the inner fuse

(2,5 A). Or send the appliance to the

manufacturer.

? THERE IS THE FLAME BUT THE

DETECTION LED IS OFF.

! The detection electrode is in short

circuit because of dirt, soot or damp.

! The detection electrode is not in a

correct position as to the flame.

! The combustion air/gas ratio is

incorrect.

! The flame makes no contact with the

burner body because air and/or gas

pressure is too high.

! The burner or CF5are not earthed

correctly.

! Short circuit or detection cable

interruption.

! Phase and neutral wire inverted.

* Eliminate the defect.

? THE APPLIANCE DOES NOT

PERFORM THE IGNITION CYCLE

AND GOES IMMEDIATELY IN

DETECTION.

! Anomaly on the detection (flame

simulation)

* Eliminate the cause of the flame

anomaly.

! Anomaly of the flame detection circuit.

* Send the appliance to the

manufacturer for its replacement.

? THE APPLIANCE DOES NOT

START EVEN IF ALL THE TROUBLES

HAVE BEEN ELIMINATED AND THE

MAIN SWITCH HAS BEEN PRESSED.

* Send the appliance to the

manufacturer for the functional

inspection.

CAUTION!!!

Danger of death due to shocks!

Before intervening on the appliance cut

off the tension to any cable.

The elimination of breakdowns can be

carried out by authorized personnel

only.

In case of improper repairs or incorrect

electrical connections, t

he good

running of the appliance is not granted.

The release at distance can be carried

out only by authorized personnel

keeping under strict control the burner

to be lighted

This document is property of Saitek Srl. Copying it and/or spreading the contents to third parties without authorization is forbidden.

Saitek Srl reserves the right to modify the present document at any moment without prior notice.

AUTOMATIC BURNER CONTROL UNIT

C F

5SERIES

MONO – DOUBLE ELECTRODE FLAME DETECTION

IN ACCORDANCE WITH STANDARD EN 298

NOTES .

Indice

Altri manuali Saitek Unità di controllo

Saitek

Saitek CF5Q Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente