Samsung IFA-E Manuale utente

Ethernet user manual

Model

name Front picture Rear picture

IFA-E

SRP-350

SRP-350II

SRP-270

IFB-E

SRP-370

SRP-372

V3.0.0 www.samsungminiprinters.com 1

1. Hardware

1) Interface version: V3.x.x

2) Difference of IFA-E and IFB-E: All features are same. Only a writing direction of model

name on metal bracket is reverse. It is because of reverse position of the main board of

SRP-350 and SRP-370.

2. Software

1) Configuration program: Configure_V3.xx.exe

- It is to set IP address and communication conditions.

2) Virtual driver (Option): VirtualCOM_V3.xx.exe

- It converts output of Serial (COM) port into output of Ethernet (TCP/IP) port.

- Applicable operating systems: Win 98, 2000, XP, 2003 server

- Contact the sales rep in case you need. It is optional software.

Note: Use the designated tool file described below for the optimal operation according to each

interface version. This version is described on the metal bracket. Each tool file can be

downloaded from website, www.samsungminiprinters.com

Interface

Version

Model

name Applicable printers Tool file Network

interface

IFA-E SRP-350, 270, 350II

V 3. x. x IFB-E SRP-370, 372

Ethernet_V3.x.zip 10/100 Base-T

All in one

V 2. x. x RIF-350E SRP-350, 270 Ethernet_V2.0.zip 10 Base-T

V 1. x. x RIF-350E SRP-350, 270 Ethernet_V1.3.zip 10 Base-T

3. Interface Card specification

1) Network interface: 10/100 Base-T All in one type (auto detection)

2) Protocol: TCP, UDP, IP, ICMP, ARP

3) IP mode: Static IP, DHCP (Dynamic Host Configuration Protocol)

4) RX buffer: 32 KByte

5) Flow control: RTS/CTS (hardware)

V3.0.0 www.samsungminiprinters.com 2

4. Ethernet interface card setup

1) Check the Ethernet interface card version and select the right tool file. V3.x.x is the latest

version.

2) Turn off the printer and install Ethernet interface card.

3) Set a serial communication speed at the highest bps.

- SRP-350: 57,600bps

- SRP-370, 372, 350II: 115,200 bps

- SRP-270: 19,200 bps

4) Connect LAN cable to Ethernet interface card and turn on the printer.

- Use Direct cable (1:1 cable) to connect to HUB(Switch).

- Use Cross cable to connect to LAN card of computer.

5) Run “Configure_V3.xx.exe”.

V3.0.0 www.samsungminiprinters.com 3

6) Select “Search”.

- If you know IP address check in the box of “Direct configuration” and enter IP address.

Then select “search”.

V3.0.0 www.samsungminiprinters.com 4

7) Select MAC address at “Board list”.

8) Enter IP Address, Subnet mask, Default Gateway according to your Sub environment.

- Caution: There is no Gateway when the printer is connected to PC direct. Write the

Same with IP address at Gateway address.

- Notice: Ethernet interface requests Gateway device to save its own IP address when

Data transmission does not take place for more than 5 minutes

9) Enter value at Local port.

(Default: 6000, choose from 6000 to 10000)

10) Set Baud rate.

(Set it as same as the printer condition. Highest bps can be used)

11) When setting finishes select “Setting”.

12) Select “Exit” and finish the program.

NOTE 1. “DHCP mode” is for DHCP server.

(DHCP: Dynamic Host Configuration Protocol)

NOTE 2. “Upload” button is used to upgrade Firmware.

V3.0.0 www.samsungminiprinters.com 5

5. Standard TCP/IP port addition

It is used when application program works with printer driver. Applicable operating systems

are Win 2000, XP, 2003 server. Follow the Installation procedure below if required.

1) Install printer driver

1-1. Download and install the printer driver from homepage. www.samsungminiprinters.com

1-2. Re-boot the personal computer.

2) Open printer properties box at installed printer driver.

V3.0.0 www.samsungminiprinters.com 6

3) Select “Ports” and click the button “Add Port”

4) Select “Standard TCP / IP port” and choose “New Port”

V3.0.0 www.samsungminiprinters.com 7

5) Go next when Standard TCP/IP Printer Port Wizard activated.

6) Write IP address at box “Printer Name or IP Address” and go next.

- IP address in this case must be the same as the value given to Ethernet card.

V3.0.0 www.samsungminiprinters.com 8

7) Go next.

8) Select “Close”

V3.0.0 www.samsungminiprinters.com 9

9) Click the button “Configure Port”

10) Enter “Port Number” and OK.

- It must be same as the value given to Ethernet card.

V3.0.0 www.samsungminiprinters.com 10

Questo manuale è adatto per i seguenti modelli

Altri manuali Samsung Scheda di rete

Samsung

Samsung MagicLAN SWL-2210M Manuale utente

Samsung

Samsung WIS09ABGN Manuale utente

Samsung

Samsung MagicLAN SWL-2200C Manuale utente

Samsung

Samsung SWL-2460C Manuale utente

Samsung

Samsung MagicLAN SWL-2000P Manuale utente

Samsung

Samsung SVMi-20i Manuale utente

Samsung

Samsung SWC-E100 Manuale utente

Samsung

Samsung MagicLAN SWL-2100N Manuale utente

Samsung

Samsung MagicLAN SWL-2300N Manuale utente

Manuali Scheda di rete popolari di altre marche

FirstComm

FirstComm OBiWiFi5G Manuale utente

Sun Microsystems

Sun Microsystems Interface Adapter Manuale utente

TRENDnet

TRENDnet TU2-ETG Manuale utente

YASKAWA

YASKAWA SI-EN3 Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Belkin

Belkin F5D7050 Manuale utente

3Com

3Com EtherLink 3C509B Manuale utente

TRENDnet

TRENDnet TEG-PCITX Manuale utente

Cisco

Cisco MC16E Manuale utente

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuale utente

TwinMOS

TwinMOS Booming Manuale utente

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuale utente

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuale utente

National Instruments

National Instruments NI 9234 Manuale utente

Hama

Hama 49276 Manuale utente

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo

Compaq

Compaq Wireless LAN 100 Manuale utente

Bose

Bose PowerMatch Dante Manuale utente