Samsung MWR-SH00 Manuale utente

Wired Remote Control

MWR-SH00

Air Conditioner

user manual

EDB98-28134A(3)

imagine the possibilities

Thank you for purchasing this Samsung product.

MWR-SH00_IB_E_28134-3.indd 13 2010-09-03 오후 1:30:16

E-2

Safety Precautions

Do not attempt to install or repair this wired remote

control by yourself.



This remote control contains no user-serviceable parts.

Always consult authorized service personnel for repairs.

When moving, consult authorized service personnel for

disconnection and installation of the remote control.

Ensure that the wall is strong enough to support the

weight of the remote control.

Must install the remote control with rated power supply.

In the event of a malfunction (burning smell, etc.),

immediately stop operation, turn off the electrical

breaker, and consult authorized service personnel.

WARNING

CAUTION



Do not use inflammable gases near the remote control.



Do not spill water into the wired remote control.



Do not operate the remote control with wet hands.



Do not install the remote control in a location where

it will come into contact with the combustible gases,

machine oil, sulphide gas, etc.



Do not press buttons with a pointed thing.



Do not pull or bend the wired remote control cable

excessively.



Do not use this wired remote control for other purpose.



Do not spray an insecticide or other combustible things

on the wired remote control.



Do not clean the wired remote control with benzene,

solvents or other chemicals.



Do not give a shock to the wired remote control or

disassemble it by yourself.

• Before using the wired remote control, read carefully these instructions.

• After reading the instructions, keep this user's manual in a handy and safe place.

If a user is changed, you must hand over the manuals.

• Never attempt to install the air conditioning system or to move the wired remote

control by yourself.

MWR-SH00_IB_E_28134.indd 2 2007-06-22 ｿﾀﾈﾄ 2:07:47

E-3

Contents

 WIRED REMOTE CONTROL

..............................................................

 GETTING STARTED

...........................................................................

 SELECTING THE AUTO MODE

..........................................................

 SELECTING THE COOL MODE

..........................................................

 SELECTING THE HEAT MODE

..........................................................

 SELECTING THE DRY MODE

............................................................

 SELECTING THE FAN MODE

............................................................

 DISPLAYING THE DEICE MODE

......................................................

 ADJUSTING THE FAN SPEED

...........................................................

MWR-SH00_IB_E_28134.indd 3 2007-06-22 ｿﾀﾈﾄ 2:07:47

E-4

Getting Started

You have just purchased a wired remote control and it has been

installed by your installation specialist.

Your User’s Manual contains much valuable information on using your

wired remote control. Please take time to read it as it will help you take full

advantages of the unit’s features.

In the manual, you will find a series of step-by-step procedures for each

function available.

The illustrations in the step-by-step procedures use 3 different symbols:

PRESS PUSH HOLD DOWN

Wired Remote Control

The wired remote control is installed on the wall.

What the function indicators mean

Filter sign indicator

 On : The filter inserted in the air conditioner needs to be cleaned. Clean up the filter

and reset the indicator by pressing the buttons at once for 5 seconds.

 Off : The filter inserted in the air conditioner is working well.

No action needed.

Mode lock indicator

 On : The mode lock function is activating. You can not change the operation mode.

Press and hold the and buttons for 5 seconds to activate and

deactivate the function.

 Off : The mode lock function is deactivating. You can change the operation mode

by short pressing the button.

You cannot activate the function with slave wired remote controls. Slave

wired remote controls just display the activating status only.

Centralized control indicator

 On : The upper controllers (For example, centralized controllers and S-NET series)

activate central control. You cannot control the devices with the wired remote

control when central control is activating.

 Off : Central control is deactivating. You can control the connected devices with the

wired remote control.

Operation mode indicator

Temperature indicator

Fan speed indicator

On/Oﬀ button

Mode selection button

Fan speed button

Temperature adjustment buttons

Function indicator

MWR-SH00_IB_E_28134.indd 4 2007-07-03 ｿﾀﾈﾄ 6:03:12

E-5

Getting Started

You have just purchased a wired remote control and it has been

installed by your installation specialist.

Your User’s Manual contains much valuable information on using your

wired remote control. Please take time to read it as it will help you take full

advantages of the unit’s features.

In the manual, you will find a series of step-by-step procedures for each

function available.

The illustrations in the step-by-step procedures use 3 different symbols:

PRESS PUSH HOLD DOWN

MWR-SH00_IB_E_28134.indd 5 2007-06-22 ｿﾀﾈﾄ 2:07:48

E-6

Selecting the Auto Mode

The room temperature and the fan speed are controlled

automatically in the Auto mode.

Press the (ON/OFF) button to turn on the indoor unit.

(Do not press the (ON/OFF) button if the remote

control is on).

Result: The air conditioner will be turned on with the

mode selected when the unit was last used.

Caution The air conditioner has a built-in protection

mechanism to prevent the unit from being

damaged when it is started immediately after

being:

 Plugged in

 Stopped

The air conditioner will start up after 3 minutes.

To select the Auto mode, press the button until is

displayed on the remote control.

Result: The air conditioner will run in Auto mode.

To adjust the temperature, press the buttons to set

the desired temperature.

The temperature can be set between 18°C(65°F) and

30°C(86°F).

Result: The temperature is adjusted by 1°C(1°F) when

the buttons are pressed.

MWR-SH00_IB_E_28134(2).indd 6 2009-03-02 ｿﾀﾈﾄ 2:16:32

E-7

Selecting the Cool Mode

Select the Cool mode to lower the room temperature.

Press the (ON/OFF) button to turn on the indoor unit.

(Do not press the (ON/OFF) button if the remote

control is on).

Result: The air conditioner will be turned on with the

mode selected when the unit was last used.

Caution The air conditioner has a built-in protection

mechanism to prevent the unit from being

damaged when it is started immediately after

being:

 Plugged in

 Stopped

The air conditioner will start up after 3 minutes.

To select the Cool mode, press the button until is

displayed on the remote control.

Result: The air conditioner will run in Cool mode.

To adjust the temperature, press the buttons to set

the desired temperature.

The temperature can be set between 18°C(65°F) and

30°C(86°F).

Result:  The temperature is adjusted by 1°C(1°F) when

the buttons are pressed.

 The air conditioner will start cooling if

the temperature set is lower than the room

temperature.

 The fan will run even if the temperature set is

higher than the room temperature.

To adjust the fan speed, refer to page 11.

Note The Cool and Heat mode cannot be selected at

the same time.

MWR-SH00_IB_E_28134(2).indd 7 2009-03-02 ｿﾀﾈﾄ 2:16:33

E-8

Selecting the Heat Mode

Select the Heat mode to raise the room temperature.

Press the (ON/OFF) button to turn on the indoor unit.

(Do not press the (ON/OFF) button if the remote

control is on).

Result: The air conditioner will be turned on with the

mode selected when the unit was last used.

Caution The air conditioner has a built-in protection

mechanism to prevent the unit from being

damaged when it is started immediately after

being:

 Plugged in

 Stopped

The air conditioner will start up after 3 minutes.

To select the Heat mode, press the button until is

displayed on the remote control.

Result: The air conditioner will run in Heat mode.

To adjust the temperature, press the buttons to set

the desired temperature.

The temperature can be set between 16°C(61°F) and

30°C(86°F).

Result:  The temperature is adjusted by 1°C(1°F) when

the buttons are pressed.

 The air conditioner will start heating if

the temperature set is higher than the room

temperature.

 The fan will run even if the temperature set is

lower than the room temperature.

To adjust the fan speed, refer to page 11.

Note The Cool and Heat mode cannot be selected at

the same time.

The Heat mode can be selected only on the heat pump models.

MWR-SH00_IB_E_28134(2).indd 8 2009-03-02 ｿﾀﾈﾄ 2:16:34

E-9

Selecting the Dry Mode

Select the Dry mode if the room is too humid.

Using this mode will slightly lower the room temperature.

Press the (ON/OFF) button to turn on the indoor unit.

(Do not press the (ON/OFF) button if the remote

control is on).

Result: The air conditioner will be turned on with the

mode selected when the unit was last used.

Caution The air conditioner has a built-in protection

mechanism to prevent the unit from being

damaged when it is started immediately after

being:

 Plugged in

 Stopped

The air conditioner will start up after 3 minutes.

To select the Dry mode, press the button until is

displayed on the remote control.

Result: The air conditioner will run in Dry mode.

To adjust the temperature, press the buttons to set

the desired temperature.

The temperature can be set between 18°C(65°F) and

30°C(86°F).

Result:  The temperature is adjusted by 1°C(1°F) when

the buttons are pressed.

 The fan speed is adjusted automatically in the

Dry mode.

MWR-SH00_IB_E_28134(2).indd 9 2009-03-02 ｿﾀﾈﾄ 2:16:35

E-10

Selecting the Fan Mode

Select the Fan mode to circulate air without changing the

temperature.

Press the (ON/OFF) button to turn on the indoor unit.

(Do not press the (ON/OFF) button if the remote

control is on).

Result: The air conditioner will be turned on with the

mode selected when the unit was last used.

Caution The air conditioner has a built-in protection

mechanism to prevent the unit from being

damaged when it is started immediately after

being:

 Plugged in

 Stopped

The air conditioner will start up after 3 minutes.

To select the Fan mode, press the button until is

displayed on the remote control.

Result: The air conditioner will run in Fan mode.

To adjust the fan speed, refer to page 11.

Note

When the air conditioner is operating in the fan

mode, you can not select the automatic fan speed.

MWR-SH00_IB_E_28134.indd 10 2007-06-22 ｿﾀﾈﾄ 2:07:52

Altri manuali per MWR-SH00

Indice

Altri manuali Samsung Telecomando

Samsung

Samsung C700 Manuale utente

Samsung

Samsung MWR-WG00JN Manuale utente

Samsung

Samsung MWR-WE13N Manuale utente

Samsung

Samsung bn59-01178w Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung SMART TV Manuale utente

Samsung

Samsung MWR-WW10N Manuale utente

Samsung

Samsung NS052LHXEA Manuale utente

Samsung

Samsung EIRC200 Manuale utente

Samsung

Samsung SWPZ01-RX Manuale utente

Samsung

Samsung MWR-TH00 Manuale utente

Samsung

Samsung MWR-WE10 Manuale utente

Samsung

Samsung MWR-WW00 Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung BN68-03092A-02 Manuale utente

Samsung

Samsung BN68-11568A Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung RMC-QTD1 Manuale utente

Samsung

Samsung MWR-SH11UN Manuale utente

Samsung

Samsung MWR-SH00N Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung SolarCell Remote Manuale utente

Samsung

Samsung TM2180E/F Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione