Satel GPRS-A Manuale utente

GPRS-A

Universal monitoring module

Quick installation guide

Full manual is available on www.satel.eu

Firmware version 1.02 gprs-a_sii_en 08/18

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • Poland

tel. +48 58 320 94 00

www.satel.eu

IMPORTANT

The module should be installed by qualified personnel.

Prior to installation, please read carefully this manual in order to avoid mistakes that can lead

to malfunction or even damage to the equipment.

Disconnect power before making any electrical connections.

Changes, modifications or repairs not authorized by the manufacturer shall void your rights

under the warranty.

The name plate of the device is located on the enclosure base.

FreeRTOS is used in this device (www.freertos.org).

SATEL's goal is to continually upgrade the quality of its products, which may result in some

changes of their technical specifications and firmware. The current information on

the introduced modifications is available on our website.

Please visit us:

http://www.satel.eu

Hereby, SATEL sp. z o.o., declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU. The declaration of

conformity may be consulted at www.satel.eu/ce

The following symbols may be used in this manual:

- note,

- caution.

This manual describes how the GPRS-A module should be installed. For further information

related to the module, including its configuration and operation, please refer to the full version

of manual, available at www.satel.eu

1. GPRS-A module installation

Disconnect power before making any electrical connections.

It is not advisable to power up the module if the antenna is not connected.

The installation to which the module is to be connected should be provided

with:

2-pole disconnector,

short-circuit protection with a 16 A time delay circuit breaker.

The GPRS-A module should be installed indoors, in spaces with normal air humidity. When

selecting the mounting location, remember that thick masonry walls, metal partitions, etc. will

reduce the range of radio signal. It is not advisable to install the module in close vicinity to

electrical installations, because this can result in malfunctioning of the device.

If the module is to comply with requirements of the EN50131 standard for Grade 2, it

must be installed in an additional enclosure that will enable it to meet requirements of

the tamper standards (e.g. in the SATEL OPU-3 or OPU-4 enclosure).

1.1 Preparing the cabling

Run the cables to be used for connecting the module with other devices to the module

installation place. Do not lay the cables in immediate vicinity of the low-voltage electrical

network wires, especially those used for supplying the high-power equipment (such as

electric motors).

It is recommended that unshielded non-twisted cable to be used.

1.2 Installation of the module

The module enclosure base makes it possible to secure the module to the mounting surface

by using e.g. a cable tie or angle hooks.

2 GPRS-A SATEL

Fig. 1. GPRS-A module.

antenna connector (the antenna is delivered with the module).

SIM card slot.

Inserting the SIM card into its slot before programming the card PIN code in the

module is not recommended (if the card requires entering the PIN code).

APS connector for a SATEL power supply unit (e.g. APS-612).

LEDs indicating the module status.

RS-232 (TTL) port.

information on how to install the SIM card.

Description of terminals

+12V – power input (12 V DC ±15%).

COM – common ground.

RING, TIP – terminals for connecting the control panel telephone communicator.

S1…S3 – 1-Wire bus (1-Wire digital temperature sensors can be connected to the bus):

S1 – common ground,

S2 – data,

S3 – power supply.

I1…I8 – inputs. They can be programmed as digital (NC or NO type) or analog ones.

O1...O2 – OC type outputs (shorted to common ground when in active state).

O3...O4 – NO type relay outputs (normally open).

AC – input for supervision of AC voltage presence.

1.2.1 Antenna

The GPRS-A module is delivered with an antenna. The antenna can be replaced with

another antenna mounted on the enclosure or at some distance from it.

Using the antenna mounted at some distance from the enclosure is recommended wherever

thick masonry walls, metal partitions etc. may decrease the range of radio signal at the

module installation place.

SATEL GPRS-A 3

The antenna must not be installed in parallel to low-voltage electrical wires, or it can affect

performance of the antenna.

1.3 Connecting the alarm control panel

Connect the control panel telephone communicator to the TIP and RING terminals.

1.4 Connecting the devices to the inputs and outputs

1. Connect the devices whose operation is to be monitored by the module to the input

terminals.

2. If the module is to monitor the presence of AC voltage fed into the device from which the

module is supplied, the wire from the secondary winding of transformer from which that

device is supplied is to be connected to the AC input terminal (see Fig. 2).

3. Connect the devices which are to be controlled by the module to the terminals of outputs.

Fig. 2. Example of connecting supply and monitoring AC voltage presence.

1.5 Connecting the digital temperature sensors (1-Wire)

You can connect up to 8 digital temperature sensors to the 1-Wire bus. The length of wires

should not exceed 30 meters. If several sensors are to be connected to the bus, it is

recommended that you use the distribution box module (MZ-2 or MZ-3).

SATEL's product offering includes the DS-T1 waterproof temperature sensors. They make it

possible to measure temperatures ranging from -35°C to 60°C. They are designed for surface

mounting indoors or outdoors. To secure them to the mounting surface, you may use

adhesives or screws. The DS-T1 sensor wires are to be connected to the bus terminals in the

following manner:

black wire – terminal S1 (common ground),

green wire – terminal S2 (data),

white wire – terminal S3 (power).

4 GPRS-A SATEL

Fig. 3. Dimensions of DS-T1 temperature sensor enclosure.

1.6 Connecting the power supply and starting the module

The module may be powered from the control panel, from an expander with power supply, or

from a power supply unit with current limitation up to 3 A. SATEL offers power supplies (e.g.

APS-612), which can be connected to the APS connector on the electronics board.

The required output current of power supply is at least 250 mA.

1. Depending on the selected method of module powering, connect the power supply unit to

the APS connector or connect the power leads to the +12V and COM terminals (use

flexible conductors with a cross-section of 0.5-0.75 mm

, or rigid conductors with a cross-

section of 1-2.5 mm

Never connect power supply to APS connector and terminals at the same time.

2. Power up the module. The module will start up.

1.7 Connecting the computer to the module

Connect the computer to the module RS-232 (TTL) port. To make the connection, use the

USB-RS converter offered by SATEL. Having connected the computer to the module, you

can:

configure the module by using the GX Soft program. You can download the GX Soft

program from the www.satel.eu website. It can be installed on computers with WINDOWS

VISTA/7/8/10 operating system. See full manual for more information.

update the module firmware (see full manual of the module).

1.8 Installing the SIM card

1. If PIN code is required by the SIM card, use the GX Soft program to program the code.

2. Power down the module.

3. Insert the SIM card into its slot as shown on the enclosure.

4. Power up the module. Logging the telephone into the GSM network may take a few

minutes.

If the module is to send data in GPRS technology, it is recommended that you use SIM

cards with a dedicated tariff plan for M2M (machine-to-machine) communication.

If the programmed PIN code is invalid, the module will report a trouble. Programming

a correct PIN code will clear the trouble.

SATEL GPRS-A 5

Restarting the module with a wrongly programmed PIN code three times will block the

SIM card. To unblock the SIM card, remove it and insert into a mobile phone. Then,

enter the PUK code.

2. Specifications

Number of inputs ..................................................................................................................... 8

Number of outputs OC type................................................................................. 2

relay, NO type ....................................................................... 2

Supply voltage ................................................................................................... 12 V DC ±15%

Standby current consumption ..........................................................................................80 mA

Maximum current consumption......................................................................................220 mA

Maximum permissible voltage on AC input ...................................................................25 V AC

O1…O2 outputs (OC type) ............................................................................. 50 mA / 12 V DC

O3…O4 outputs (relay, NO type)................................................................ 1000 mA / 30 V DC

Environmental class according to EN50130-5 ......................................................................... II

Operating temperature range...................................................................................-10...+55°C

Maximum humidity..........................................................................................................93±3%

Enclosure dimensions......................................................................................83 x 65 x 23 mm

Weight............................................................................................................................... 110 g

Indice

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente