Satel AQUA Series Manuale utente
®
DIGITAL PASSIVE INFRARED DETECTOR
AQUA RING
CEILING MOUNT
aquaring_e 06/04
The microprocessor-based, fully
digital AQUA series detectors
feature high sensitivity and
interference resistance. A dual pyro
electric element is used in the AQUA
RING detector.
TERMINALS:
NC - alarm relay (NC)
TMP - tamper contact (NC)
COM - ground (0V)
12V - supply input (9-16V DC)
Three pairs of pins are used to set the detector working parameters (see Table)
JP1 JP2 JP3
Low sensitivity
Medium sensitivity
High sensitivity
LED indicator ON
LED indicator OFF
- pins open - pins shorted
The LED lights red when the detector is actuated, which enables the installer to
check the detector for correct functioning and to approximately determine the
protected area.
For 30 seconds after the power is turned on, the detector remains in a starting
state, which is signalized by rapid LED blinking. Only then the detector enters its
operational readiness state.
The detector monitors the supply voltage. If the voltage drops below 9V (±5%) for
more than 2 seconds, the detector will signalize a violation state until a voltage of
minimum 9V (±5%) is restored.
INSTALLATION
The detector is designed for ceiling mount. Prior to installation, remove the
electronics board and make adequate openings for screws and cable in the
housing.
Be careful so as not to soil or damage the pyro element in the process of
installation.
LED
NC NC TMP TMP COM 12V
PIR SENS.
LED ON/OFF
JP1
JP2
JP3
pyro element
tamper contact
relay
positioning scale operating parameter
setting pins
Figure 1. View of detector electronics board
Figure 3 shows typical examples of connecting the detectors in EOL (parameter)
configuration and 2EOL (two-parameter) configuration. Resistors should be
mounted inside the detector housing.
2R
NC NC TMP TMP COM 12V
AQUA RING detector
Z2 - programmed as „24h TAMPER” – NC type
+12V COM Z1 Z2 COM Z3 Z4 COM Z5 Z6 COM Z7 Z8 COM
R R
NC NC TMP TMP COM 12V
AQUA RING detector
Figure 3. Examples of detector connection
close
open
Figure 2. Detector view
TECHNICAL DATA
Nominal supply voltage ...............................................................................12V DC
Mean power consumption (±10%)..................................................................9.5mA
Violation signaling time........................................................................................ 2s
Protected area: when mounted at a height of 2.4m........................................36m2
when mounted at a height of 3.7m........................................80m2
Operating temperature range ................................................................-10...+50°C
Detectable motion speed....................................................................... up to 3 m/s
Dimensions ........................................................................................... ø97x29mm
Recommended installation height............................................... from 2.2m to 4.5m
Latest EC declaration of conformity and product approval certificates can
be downloaded from our Web site www.satel.pl
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
info@satel.pl
www.satel.pl
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Satel Sensore di sicurezza
Satel
Satel GRAPHITE Manuale utente
Satel
Satel TD-1 Manuale utente
Satel
Satel AOD-200 Manuale utente
Satel
Satel APMD-150 Manuale utente
Satel
Satel SILVER Manuale utente
Satel
Satel AOCD-250 Manuale utente
Satel
Satel A D-200 Series Manuale utente
Satel
Satel AGD-100-BR Manuale utente
Satel
Satel COBALT Pro Manuale utente
Satel
Satel ARD-100 Manuale utente
Satel
Satel COBALT Manuale utente
Satel
Satel OPAL Manuale utente
Satel
Satel INDIGO TESTER Manuale utente
Satel
Satel abax 2 ADD-200 Manuale utente
Satel
Satel AMD-103 Manuale utente
Satel
Satel ACTIVA-2 Manuale utente
Satel
Satel SLIM-DUAL-PRO Manuale utente
Satel
Satel micra MPD-310 Pet Manuale utente
Satel
Satel APD-100 Manuale utente
Satel
Satel AGD-200-BR Manuale utente
