Satel XD-2L Manuale utente
XD-2L
Multipurpose detector xd-2L_sii_en 02/23
EN
Quick installation guide
Full manual is available on www.satel.pl.Scan the QR code to
go to our website and download the manual.
The device should be installed by qualified professionals.
Before installation, please read the full manual thoroughly.
Changes, modifications or repairs not authorized by the manufacturer shall void
your rights under the warranty.
Disconnect power before making any electrical connections.
The device is designed for indoor installation.
The XD-2L detector can work as:
magnetic contact,
shock detector,
shock detector and magnetic contact,
water flood detector.
For details on how to select the detector type and the place of installation, see the full manual
for the device.
Prepare the cables for making connections and run them to the location where the device will
be installed. The cabling should not be run in close vicinity of low-voltage electrical system
wires, and especially of power cables for high-power equipment (such as electric motors).
1. Open the detector enclosure.
2. Configure the detector (see the full manual).
3. Make the opening for cable in the enclosure base.
4. Run the cable through the opening.
5. Using wall plugs (anchors) and screws, secure the enclosure base to the mounting
surface. Select wall plugs designed specifically for the mounting surface.
6. Connect the wires to the appropriate terminals:
LED - enable/disable the LED indicator.
Z1 - input for connecting an NC type detector (e.g. other magnetic contact) or a flood
probe (if the input is unused, the terminal must be connected to common
ground).
S - alarm output (NC relay) used when the two output mode is activated (see the
full manual).
2 SATEL
EOL - alarm output. It can operate as 2EOL/NC or NC (see the full manual).
COM - common ground.
+12V - power input.
7. Close the detector enclosure.
8. When the detector is used as a magnetic contact, install the magnet (see the full manual).
9. When the detector is used as a water flood detector, install the probe.
10.Power up the detector.
11.Check the device for proper functioning.
SATEL 3
4 SATEL
The declaration of conformity may be consulted at www.satel.pl/ce
SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.pl
Indice
Altri manuali Satel Sensore di sicurezza
Satel
Satel AOCD-250 Manuale utente
Satel
Satel MGD-300 Manuale utente
Satel
Satel AQUA PET Manuale utente
Satel
Satel COBALT Pro Manuale utente
Satel
Satel VD-1 Manuale utente
Satel
Satel APD-100 Manuale utente
Satel
Satel SLIM-DUAL-LUNA-PET Manuale utente
Satel
Satel AXD-200-DG Manuale utente
Satel
Satel ASD-100 Manuale utente
Satel
Satel GRAPHITE Manuale utente
Satel
Satel AOD-200 Manuale utente
Satel
Satel SLIM-PIR-PRO Manuale utente
Satel
Satel AQUA PRO Manuale utente
Satel
Satel micra MXD-300 Manuale utente
Satel
Satel SX6-TO Manuale utente
Satel
Satel GRAPHITE Manuale utente
Satel
Satel SPL-TO Manuale utente
Satel
Satel A D-200 Series Manuale utente
Satel
Satel INDIGO Manuale utente
Satel
Satel FD-1 Manuale utente
