SawStop MB-IND-500 Manuale utente
SawStop®
ASSEMBLY INSTRUCTIONS
Mobile Base Conversion Kit
For use with the Professional Cabinet Saw
MB-IND-500
1. Never place ngers, toes or other body parts under the mobile base. The base may suddenly lower on you and
cause a severe injury.
2. Do not attempt to use or move the saw on an inclined surface. The saw is very heavy and dicult to stop on
an inclined surface. Attempting to use or move the saw on an inclined surface could result in a severe injury.
3. Make sure the saw is fully lowered to the ground and stable before operating the saw. Otherwise, the saw could
move unexpectedly and cause a severe injury.
4. Do not raise the saw higher than necessary to move it. Instead, raise the saw only enough to provide sucient
ground clearance.
5. Be sure to unplug or disconnect the saw from power before moving or repositioning it. The main power cord or
the power outlet could be damaged if the saw is not disconnected from power before moving it.
1 SawStop Mobile Base Conversion Kit
Safety
While unpacking your mobile base conversion kit verify that all the components shown on this page are included.
Unpacking Your Conversion Kit
hold-down brackets (2)
conversion linkage bars (2)
hardware bag
assembly instructions
SawStop®
ASSEMBLY INSTRUCTIONS
Mobile Base Conversion Kit
Model MB-IND-500
For use with the Professional Cabinet Saw
Lower
Raise
1. Never place fingers, toes or other
bodyparts under the mobile base.
2. Always use the saw and the mobile
baseon a level surface.
3. Do not continue to step on the foot
pedalonce the upper limit is reached.
4. Lower the saw before use. Never use
thesaw when it is raised off the floor.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
The SawStop Industrial Mobile Base is designed to t the SawStop Industrial Cabinet Saw; however this mobile
base conversion kit allows the Industrial Mobile Base to be used with the SawStop Professional Cabinet Saw.
In order to convert the mobile base for use with the SawStop Professional Cabinet Saw, rst locate all of the
conversion kit components shown on page
1. All of the hardware needed to convert the
mobile base is located in the hardware bag. If
you are missing the hardware bag or any of the
other components, call the SawStop Service
Department at 503-582-9934 for replacements.
1. Remove the original linkage bar on the
left side of the mobile base by unscrewing
the two M8 shoulder screws with a 5 mm
hex key (see Fig. 1). The shoulder screws
may be dicult to remove because they
were installed with a thread adhesive.
The original linkage bar and the two M8
shoulder screws may be discarded.
SawStop Mobile Base Conversion Kit 2
Assembling Your Mobile Base
Fig. 2
Fig. 1
Fig. 3
2. Repeat the previous step to remove the
original linkage bar on the right side of the
mobile base (see Fig. 2).
3. You must now move the rear support
strap forward to accommodate the smaller
cabinet of the Professional Cabinet Saw.
Begin by removing the two M8 shoulder
screws that mount the rear support
assembly to the mobile base frame with
a 5 mm hex key, as shown in Fig. 3. The
rear support assembly will be used in the
following step, but you may discard the
two M8 shoulder screws.
remove the original
linkage bar on the right
side of the mobile base
remove the two M8 shoulder
screws that mount the rear
support assembly to the
mobile base frame
rear support
assembly
rear face of mobile
base frame
rear support
strap
remove the original linkage
bar on the left side of the
mobile base
Raise
1. Never place fingers, toes or other
bodyparts under the mobile base.
2. Always use the saw and the mobile
baseon a level surface.
3. Do not continue to step on the foot
pedalonce the upper limit is reached.
4. Lower the saw before use. Never use
thesaw when it is raised off the floor.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Lower
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Raise
. Never place fingers, toes or other
bodyparts under the mobile base.
2. Always use the saw and the mobile
baseon a level surface.
3. Do not continue to step on the foot
pedalonce the upper limit is reached.
4. Lower the saw before use. Never use
thesaw when it is raised off the floor.
!
WARNING
Lower
4. Take the rear support assembly and move it forward until the two mounting holes align with the next set of
holes in the mobile base frame, as shown in Fig. 4. Mount the rear support assembly to the mobile base
frame with two new M8 x 15.7 shoulder socket screws from the hardware bag. Fully tighten the two M8 x 15.7
shoulder socket screws with a 5 mm hex key.
3 SawStop Mobile Base Conversion Kit
Assembling Your Mobile Base
5. Locate the two conversion linkage bars and the remaining four M8 x 15.7 shoulder socket screws. Use two of
the M8 x 15.7 shoulder screws to install one of the conversion linkage bars on the left side of the mobile base
(see Fig. 5a). The screws pass through the clearance holes in the conversion linkage bar and thread into the
corresponding holes in the rear support assembly and the front bell link. Use the remaining two M8 x 15.7
shoulder socket screws to install the other conversion linkage bar on the right side of the mobile base (see
Fig. 5b). Fully tighten all four screws using a 5 mm hex key.
move the rear
support assembly
forward until the
two mounting holes
align with the next
set of holes in the
mobile base frame
Fig. 4
M8 x 15.7 shoulder
socket screw
M8 x 15.7 shoulder
socket screw
new
mounting
hole
original mount-
ing hole
new
mounting
hole
Fig. 5a Fig. 5b
M8 x 15.7 shoulder
socket screws
install a conver-
sion linkage bar on
the left side of the
mobile base
install a conversion
linkage bar on the right
side of the mobile base
front
bell link
rear support
assembly
M8 x 15.7 shoulder
socket screws
Raise
1. Never place fingers, toes or other
bodyparts under the mobile base.
2. Always use the saw and the mobile
baseon a level surface.
3. Do not continue to step on the foot
pedalonce the upper limit is reached.
4. Lower the saw before use. Never use
thesaw when it is raised off the floor.
!
WARNING
Lower
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
SawStop Mobile Base Conversion Kit 4
6. The conversion kit includes hold-down brackets to hold the saw in the mobile base. These hold-down brackets
may already be installed on your mobile base. Refer to Fig. 7a and Fig. 7b for the location for each hold-down
bracket. If these hold-down brackets are already installed, skip to step 8. If they are not already installed, you
must now attach them. Begin by removing the two M8 shoulder screws that mount the left side of the front and
rear support straps to the frame with a 5 mm hex key, as shown in Fig. 6. The shoulder screws may be dicult
to remove because they were installed with a thread adhesive. The two M8 shoulder screws may be discarded.
7. Locate the two hold-down brackets and the two M8 x 18 shoulder socket screws. Use one of the M8 x 18
shoulder socket screws to install one of the hold-down brackets to the inside of the rear support strap (see
Fig. 7a). Note that the shoulder screw can only pass through the larger hole in the hold-down bracket and the
hold-down bracket must be oriented so that it bends inward toward the center of the mobile base (see Fig. 7a).
Use the remaining M8 x 18 shoulder socket screw to install the other hold-down bracket to the inside of the
front support strap (see Fig. 7b). Fully tighten both screws using a 5 mm hex key.
Assembling Your Mobile Base
Fig. 6
remove the two M8
shoulder screws that
mount the left side
of the front and rear
support straps
front support
strap
rear support
strap
Fig. 7a Fig. 7b
M8 x 18 shoulder
socket screw
M8 x 18 shoulder
socket screw
install a hold-down bracket
to the inside of the rear
saw strap as shown
install a hold-down bracket
to the inside of the front
support strap as shown
8. The mobile base is now ready for your Professional Cabinet Saw, but before placing the saw on the mobile
base, it is important to rotate the rear hold-down bracket back as far as possible and to rotate the front hold-
down bracket forward as far as possible (see Fig. 8). To safely place the saw into the mobile base, you will
need at least four people to lift the saw o the
oor and then lower it onto the mobile base.
Have one person lift each corner of the cast
iron table top. If your saw has an extension
table, have the two people on the right side
of the saw lift on the extension rails near the
outer corner of the cast iron extension wing,
not at the end of the extension table. If a fth
person is available, it may be easier to have
four people lift the saw and the fth person
slide the base under the saw.
Make sure the mobile base is centered
underneath the table saw and that the foot
pedal is in the front. The saw should sit on the
front and rear support straps extending across
the interior of the mobile base, and the front
of the cabinet should be touching the inside of
the front face of the mobile base frame (see
Fig. 8).
Neverplace fingers,
toesor other body parts
underthe mobile base.
!
WARNING
1. Never place fingers, toes or other
bodyparts under the mobile base.
2. Always use the saw and the mobile
baseon a level surface.
3. Do not continue to step on the foot
pedalonce the upper limit is reached.
4. Lower the saw before use. Never use
thesaw when it is raised off the floor.
!
WARNING
Raise
Neverplace fingers,
toesor other body parts
underthe mobile base.
!
WARNING
Low
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
5 SawStop Mobile Base Conversion Kit
9. Locate the two self-tapping screws and the two M4 x 12 x 1 washers. Some cabinet congurations will have
pre-drilled holes for the self-tapping screws. If your saw cabinet does not have pre-drilled holes, or you are
having diculty aligning the holes, rotate the rear hold-down bracket until the top hole is over the at face of
the cabinet. Place one of the M4 x 12 x 1 washers over the end of one of the self-tapping screws and use a
drill with a 1⁄4 inch hex drive bit to mount the rear hold-down bracket to the cabinet, as shown in Fig. 9a. There
is no need to pre-drill a hole for the self-tapping screws, but be careful not to overtighten the screws or the
threads in the cabinet may strip out. Now, rotate the front hold-down bracket until it is vertical and repeat the
same procedure to mount it to the cabinet, as shown in Fig. 9b.
Fig. 9a Fig. 9b
M4 x 12 x 1
washer
self-tapping
screw
rotate the rear hold-
down bracket until the
top hole is over the at
face of the cabinet and
then mount it to the cab-
inet with a washer and a
self-tapping screw
rotate the front
hold-down bracket
until it is vertical
and then mount it
to the cabinet with
a washer and a
self-tapping screw
M4 x 12 x 1
washer
self-tapping
screw
Congratulations, the assembly is now complete. Please see the Industrial Mobile Base Owner’s Manual for
instructions on how to use and adjust the mobile base and for information on hydraulic jack maintenance.
Assembling Your Mobile Base
Fig. 8
straps that
support the
saw
the front of the
cabinet should be
touching the inside of
the front face of the
mobile base frame
rotate hold-down
bracket back
rotate hold-down
bracket forward
Mobile Base Conversion Kit Exploded View
Mobile Base Conversion Kit Parts List
No. Description Part No. Qty.
Complete Mobile Base Conversion Kit MB-IND-500 1
1Conversion Linkage Bar MB-IND-501 2
2Hold-Down Bracket MB-IND-502 2
3M8 x 1.25 x 15.7 Shoulder Socket Screw (with Felt Adhesive Pad) MB-IND-503 6
4M8 x 1.25 x 18 Shoulder Socket Screw (with Felt Adhesive Pad) MB-IND-504 2
5M4 x 12 x 1 Washer MB-IND-505 2
6Self-Tapping Screw MB-IND-506 2
N/A Hardware Bag MB-IND-507 1
N/A Assembly Instructions MB-IND-508 1
SawStop Mobile Base Conversion Kit 6
Raise
1. Never place fingers, toes or other
body parts under the mobile base.
2. Always use the saw and the mobile
base on a level surface.
3. Do not continue to step on the foot
pedal once the upper limit is reached.
4. Lower the saw before use. Never use
the saw when it is raised off the floor.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
Never place fingers,
toes or other body parts
under the mobile base.
!
WARNING
1
1
2
2
3
3
3
3
3
3
4
4
5
5
6
6
SawStop, LLC
11555 SW Myslony St.
Tualatin, Oregon 97062
www.sawstop.com
Main Phone - (503) 570-3200
Service - (503) 582-9934
Fax - (503) 570-3303
Email: [email protected]
May 2017
IG PCS 18 0005 00
Copyright SawStop, LLC
All Rights Reserved.
Updates of this manual may be available at www.sawstop.com.
Altri manuali SawStop Accessori per utensili elettrici
