SawStop MB-PCS-000 Manuale utente

SawStop®

INSTALLATION GUIDE

Professional Cabinet Saw

Mobile Base

Model MB-PCS-000

Raise

Lower

Never place fingers,

toes or other body par

under the mobile bas

WARNING

1. Never place fingers, toes or other body

parts under the mobile base.

2. Always use the saw and the mobile base

on a level surface.

3. Lower the saw before use. Never use

the saw when it is raised off the floor.

4. Lower the saw slowly, do not let it

drop back to the floor.

WARNING

Safety

1. Never place ngers, toes or other body parts under the saw when it is raised onto the mobile base. The base

may suddenly lower and cause a severe injury.

2. Do not attempt to use or move the saw on an inclined surface because the weight of the saw makes it di󰀩cult

to stop. Attempting to use or move the saw on an inclined surface could result in a severe injury.

3. Make sure the saw is fully lowered to the ground and stable before operating the saw. Otherwise, the saw could

move unexpectedly and cause a severe injury.

4. Be sure to unplug or disconnect the saw from power before moving or repositioning it. The main power cord or

the power outlet could be damaged if the saw is not disconnected from power before moving it.

Note:If you are using the SawStop out-feed table you must remove it before moving your saw with the

mobile base. Attempting to lift the saw with the out-feed table attached may damage the out-feed table.

SawStop warrants to the original retail purchaser of the mobile base accompanying this guide that the mobile

base will be free from defects in material and workmanship for ONE YEAR from the date of purchase. This warranty

does not apply to defects arising from misuse, abuse, negligence, accidents, normal wear-and-tear, unauthorized

repair or alteration, or lack of maintenance.

Please contact SawStop to take advantage of this warranty. If SawStop determines the mobile base is

defective in material or workmanship, and not due to misuse, abuse, negligence, accidents, normal wear-and-

tear, unauthorized repair or alteration, or lack of maintenance, then SawStop will, at its expense and upon proof

of purchase, send replacement parts to the original retail purchaser necessary to cure the defect. Alternatively,

SawStop will repair the mobile base, provided it is returned to SawStop, shipping prepaid, within the warranty

period. This warranty is void if the mobile base is modied without the prior permission of SawStop, or if the mobile

base is located or has been used outside of the country where the authorized SawStop distributor from whom the

mobile base was purchased resides.

SawStop disclaims any and all other express or implied warranties, including merchantability and tness for a

particular purpose. SawStop shall not be liable for death, injuries to persons or property, or incidental, consequential,

contingent or special damages arising from the use of the mobile base.

This warranty gives you specic legal rights. You may have other rights which, in the United States, vary from

state to state.

Warranty

1SawStop®Professional Cabinet Saw Mobile Base

While unpacking your mobile base verify that all the components shown on this page are included.

Unpacking Your Mobile Base

To install your mobile base on a new Professional Cabinet Saw

that has not yet been assembled...GO TO PAGE 2.

To install your mobile base on a Professional Cabinet Saw that

already has a fence system installed ...GO TO PAGE 10.

Important:

This manual contains two di󰀨erent sets of instructions.

-OR-

pedal assembly

3” caster

(two)

3” wheel

(two)

caster support plate

caster extension tube

caster support

wheel support

hardware pack owner’s manual

SawStop

linkage bar

SawStop

OWNER’S MANUAL

Professional Saw Mobile Base

ModelMB-PCS-000

1. Neverplace fingers, toes or other body

parts under the mobile base.

2. Always use the saw and the mobile

base on a level surface.

3. Lowerthe saw before use. Never use

the saw when it is raised off the floor.

4. Lowerthe saw slowly, do not let it

drop back to the floor.

WARNING

5 mm short-arm

hex key

Professional Cabinet Saw Mobile Base Hardware Pack

Extension Spring, (1) 8

Lock Washers,

M8 x 13.6 (4) 2

Washers,

M8 x 18 (2) 4

Washers,

M6 x 16 (2) 14 Flange Lock

Nuts, M6 (2) 15

Hex Bolts,

M6 x 40 (2) 13

Lock Washers,

M10.5 x 17 (4) 11 CasterNuts,

3/8” thread (2) 16

Button Head Socket

Bolts, M8 x 35 (2) 1

Lock Nuts,

M6 (2) 7Shoulder Socket

Screw, M8 x 17.7 (1) 9ButtonHead Socket

Bolts, M10 x 40 (2) 10

Washers,

M10.5 x 20 (4) 12

Button Head Socket

Bolts, M8 x 20 (2) 3

Button Head Shoulder

Socket Bolts, M8 x 20 (2) 5

Fixed Wheel Axles 6

2 SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

2. Locate all of the mobile base components shown on page 1. All of the hardware needed to install the mobile

base is located on the hardware pack (see Fig. 2). In order to easily identify the hardware used in each of

the following steps, the di󰀨erent pieces of hardware are numbered on the hardware pack and in the gures.

If you are missing the hardware pack or any of the other mobile base components, call the SawStop Service

Department at 503-582-9934 for replacements.

You will need the following tools to complete the

mobile base installation:

• 5 mm hex key

• 6 mm hex key

• 10 mm socket

• 10 mm wrench

• 14 mm wrench

• 17 mm wrench

1. You need access to the bottom of your saw to install the mobile base. The easiest and safest way to provide

that access is to leave the saw facing up on the packaging and slide it so that the bottom of the cabinet

overhangs the edge of the packaging as shown in Fig. 1. The saw should overhang the packaging enough to

clear the rectangular and circular holes around the bottom of the cabinet.

Fig. 1

START HERE to install your mobile base on a new

Professional Cabinet Saw that has not yet been assembled.

Fig. 2

Professional Cabinet Saw Mobile Base Hardware Pack

Extension Spring, (1) 8

Lock Washers,

M8 x 13.6 (4) 2

Washers,

M8 x 18 (2) 4

Washers,

M6 x 16 (2) 14 Flange Lock

Nuts, M6 (2) 15

Hex Bolts,

M6 x 40 (2) 13

Lock Washers,

M10.5 x 17 (4) 11 Caster Nuts,

3/8” thread (2) 16

Button Head Socket

Bolts, M8 x 35 (2) 1

Lock Nuts,

M6 (2) 7Shoulder Socket

Screw, M8 x 17.7 (1) 9Button Head Socket

Bolts, M10 x 40 (2) 10

Washers,

M10.5 x 20 (4) 12

Button Head Socket

Bolts, M8 x 20 (2) 3

Button Head Shoulder

Socket Bolts, M8 x 20 (2) 5

Fixed Wheel Axles 6

saw overhangs

the edge of the

packaging

3SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

3. Locate the caster support, the

linkage bar, two M8 x 35 button

head socket bolts, and two M8

x 13.6 lock washers. Note that

one end of the caster support

has a mounting shoulder and

the other end does not (see

Fig. 3a). Mount the linkage

bar to the inside of the caster

support arm nearest the end

without the mounting shoulder

as shown in Fig. 3b. Use the

button head sockets bolts, lock

washers, and a 5 mm hex key

to mount the linkage bar to the

caster support arm. Make sure

the linkage bar is positioned as

shown in Fig. 3b with the caster

support in the notch on the

linkage bar.

Fig. 3a with mounting shoulderwithout mounting shoulder

4. With the saw resting on the packaging, facing up

and overhanging the edge, place the ends of the

two caster support arms through the two holes in

the inside right face of the saw, as shown in Fig.

4. Make sure that the caster support is oriented

so that the linkage bar is next to the front of the

cabinet.

linkage bar

caster

support

caster

support

arm

end without

a mounting

shoulder

notch

Fig. 3b

Fig. 4

linkage bar

front

mounting

shoulder

down

4 SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

6. Align the front end of the caster support with the mounting hole in the lower right corner of the front of the

cabinet and secure that end of the caster support to the cabinet with an M8 x 20 button head shoulder socket

bolt (see Fig. 6). Note that this bolt is di󰀨erent than the bolt used to secure the rear of the caster support to the

cabinet. Fully tighten the bolt using a 5 mm hex key.

5. The end of the caster support next to the back of the saw is the end with the mounting shoulder. Insert the

mounting shoulder through the mounting hole in the rear of the cabinet and secure that end of the caster

support to the cabinet with one M8 x 20 button head socket bolt, one M8 x 13.6 lock washer, and one M8 x 18

washer (see Fig. 5). Fully tighten the bolt using a 5 mm hex key.

Fig. 5

mounting

shoulder

Fig. 6

Raise

Neverplacefingers,

toesorother body parts

underthemobile base.

WARNING

5SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

Fig. 7

7. Locate the wheel support and the two 3 inch wheels. Note that one end of the wheel support has a mounting

shoulder and the other end does not. Mount one of the 3 inch wheels between the two support arms nearest

the end of the wheel support that has the mounting shoulder using a xed wheel axle and an M6 lock nut

from the hardware pack (see Fig. 7). The xed wheel axle passes through the outer support arm and threads

through the inner support arm. Fully tighten the nut using a 17 mm wrench and a 10 mm wrench.

8. Mount the second 3 inch wheel

to the other end of the wheel

support using the other xed

wheel axle, but do not thread a

nut onto the axle (see Fig. 8).

The xed wheel axle passes

through the outer support arm

and threads through the inner

support arm. Set the wheel

support aside for a moment.

9. Locate the pedal assembly

and insert it into the hole in

the left side of the cabinet

as shown in Fig. 9. Insert

the pedal assembly as far as

possible and make sure that

the foot pad is facing the top of

the cabinet.

foot pad pedal assembly

Fig. 8

Fig. 9

3 inch wheel

support arms 6

end with a mounting

shoulder

wheel support

3 inch wheel

support arms

Raise

Neverplace fingers,

toesor other body parts

underthe mobile base.

WARNING

6 SawStop®Professional Cabinet Saw Mobile Base

10. Remove the extension spring from the hardware

pack and attach one end of the spring to the small

pin in the pedal assembly by sliding one end of the

spring through the hole in the small pin. Stretch

the other end of the spring over the large pin in the

pedal assembly (see Fig. 10). There is a circular

groove on the large pin to hold the spring in place.

Fig. 10

Installing Your Mobile Base - Method 1

Fig. 11

smaller pin

larger pin

mounting shoulder down

11. Take the wheel support and place it inside the

cabinet and behind the pedal assembly, as shown

in Fig. 11. Make sure that the end of the wheel

assembly with the mounting shoulder is at the rear

of the cabinet. It might be a little awkward to position

the wheel support behind the pedal assembly, but

the pedal assembly is loose and can move to allow

you to position the wheel support. When the wheel

support is correctly positioned the pedal assembly

will be between the two wheels (see Fig. 11). The

pedal assembly must be inserted through the hole

in the cabinet before the wheel support is placed

inside the cabinet, otherwise the wheel support will

block the pedal assembly.

Raise

Neverplace fingers,

toesor other body parts

underthe mobile base.

WARNING

7SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

Fig. 13a

align the notches for

the wheel support

release

lever

foot

pad

mounting

hole

13. You must now position the pedal assembly so

that it ts against the wheel support. The pedal

assembly includes notches shaped to t over the

wheel support bar, and a mounting hole shaped

to t over the threaded end of the xed wheel

axle (see Fig. 13b). Squeeze the foot pad and

the release lever together until the notches for the

wheel support align as shown in Fig. 13a. With the

slots aligned, position the pedal assembly so that

the wheel support bar ts in the notches and so that

the threaded end of the xed wheel axle extends

through the mounting hole in the pedal assembly.

When positioning the pedal assembly make sure

the linkage bar extending from the caster support

is rotated outwards so that it is farther away from

the saw than the pedal assembly as shown in Fig.

13b. Use an M6 lock nut from the hardware pack to

secure the pedal assembly to the xed wheel axle

as shown in Fig. 13b. Fully tighten the nut using a

17 mm wrench and a 10 mm socket.

Fig. 13b

threaded end

of the xed

wheel axle

wheel support

bar

this end of the linkage

bar must be farther

away from the saw than

the pedal assembly

12. Insert the mounting shoulder on the rear end of

the wheel assembly through the mounting hole

on the rear of the cabinet and secure that end to

the cabinet with one M8 x 20 button head socket

bolt, one M8 x 13.6 lock washer, and one M8 x 18

washer (see Fig. 12). Fully tighten the bolt using a

5 mm hex key.

Fig. 12

Raise

Never place fingers,

toes or other body parts

under the mobile base.

WARNING

1. Neverplace fingers, toes or other body

parts under the mobile base.

2. Always use the saw and the mobile base

on a level surface.

3. Lowerthe saw before use. Never use

the saw when it is raised off the floor.

4. Lowerthe saw slowly, do not let it

drop back to the floor.

WARNING

8 SawStop®Professional Cabinet Saw Mobile Base

Installing Your Mobile Base - Method 1

14. Align the front end of the wheel support with

the mounting hole in the lower left corner of the

front of the cabinet. Secure that end of the wheel

support to the cabinet with an M8 x 20 button head

shoulder socket bolt (see Fig. 14). Note that this

bolt is di󰀨erent than the bolt used to secure the

rear of the wheel support to the cabinet. Fully

tighten the bolt using a 5 mm hex key.

Fig. 14

15. You must now connect the pedal assembly to the

linkage bar. There is a slot in the linkage bar near

the pedal assembly and there is a plastic washer

and threaded hole on the pedal assembly near the

linkage bar. Pivot the linkage bar and the pedal

assembly until the slot in the linkage bar aligns

with the plastic washer and the threaded hole in

the pedal assembly. Insert an M8 x 17.7 shoulder

socket screw through the slot in the linkage bar

and thread it into the hole in the pedal assembly

(see Fig. 15). Fully tighten the screw with a 5 mm

hex key.

16. Stand up your saw as described in step 4 on the

back of the unpacking sheet that came with your

saw and also in your Professional Cabinet Saw

Owner’s Manual. With the saw in the upright

position, mount the caster extension bar to the

two caster support arms that extend from the right

side of the cabinet. Make sure that the warning

label is facing outward. Use two M10 x 40 button

head socket bolts, two M10.5 x 17 lock washers,

and two M10.5 x 20 washers to mount the caster

extension bar to the caster support arms (see Fig.

16). Fully tighten the bolts with a 6 mm hex key.

Fig. 15

linkage

bar slot

Fig. 16

caster support arms

caster extension bar

12 10

Indice

Altri manuali SawStop Accessori per utensili elettrici

SawStop

SawStop MB-IND-500 Manuale utente

SawStop

SawStop TSA-SA70 Manuale utente

Manuali Accessori per utensili elettrici popolari di altre marche

Bosch

Bosch OSC004 Manuale utente

Rockler

Rockler 57510 Manuale utente

Bosch

Bosch RA1054 Istruzioni per il montaggio

Grizzly

Grizzly T10808 Manuale utente

Kitagawa

Kitagawa SC N Series Manuale utente

Wolfcraft

Wolfcraft FKS 145 Guida rapida

ADAMAS

ADAMAS B32 Manuale utente

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Manuale utente

Echo

Echo Speed-Feed Universal 400 LH/RH Manuale utente

SCHUNK

SCHUNK ROTA TB-TBS-EP Istruzioni utente

Schmid

Schmid RAPID Secure XL Manuale utente

Drill Master

Drill Master 360X Manuale utente

Toro

Toro 138-5050 Manuale utente

jbc

jbc SF-SD Manuale utente

Bosch

Bosch GTA 3800 Professional Istruzioni per il montaggio

RG AVAK

RG AVAK MaxDrill Series Manuale utente

infaco

infaco PW3 Manuale utente

Gloria

Gloria CUT & BRUSH Manuale utente