Scientific SMO702 Manuale utente

Digital Oscilloscopes

SMO702, SMO1002

User Manual

Scientific Mes-Technik Pvt. Ltd.,

B-14 Industrial Estate, Pologround,

Indore- 452015 (India)

Tel : 0731-2422330/31/32/33

Fax : 0731-2422334,561641

Email : [email protected]

Website: www.scientificindia.com

This instrument contains proprietary information, no part of this manual may be photocopied, reproduced or

translated without any prior written consent.

Information in this manual supercede all corresponding previous released material.

Scientific continues to improve products and reserves rights to amend part or all of the specifications,

procedures, equipment at any time without notice.

Rev 1.00/ 0115

2User Manual SMO702, SMO1002

Digital Oscilloscopes

SMO702, SMO1002

Table Of Contents

Safety Summary

Introduction

Technical Specifications

Front Panel Controls

Rear Panel & Side Panel Controls

Operating Instructions

First Time Operation

Function Checking

Probe

1. Probe Safety

2. Probe Attenuation Setting

3. Probe Compensation

Functions Instruction and Operation

A) Menu and Control Button

B) Connector

C) Auto Setup

D) Default Setup

E) Universal Knob

F) Vertical System

A) CH1, CH2 Channel

b) Using Vertical “Position” Knob and “Volt/div” Knob

c) Math Functions

d) Using Ref

G) Horizontal System

a) Horizontal Control Knob

b) Window Zone

H) Trigger System

a) Signal Source

b) Trigger Type

c) Coupling

d) Position

d) Slope & Level

e) Trigger Holdoff

I) Acquiring Signals System

J) Display System

a) X-Y Format

K) Measure System

a) Scale Measurement

b) Cursor Measurement

c) Auto Measurement

L) Storage System

M) Utility System

User Manual SMO702, SMO1002

a) System Status

b) Language

c) Print

d) Self Calibration

e) Self Test

f) Updating the System Software

g) Pass/Fail

h) Waveform Recorder

i) Recorder

j) Remote Control

N) Online Help Function

Prompting Messages and Troubleshooting

A) Prompting Messages:

B) Troubleshooting

Default Setting

Maintenance

Despatch Procedure for Service

Warranty Conditions

100

101

102

User Manual SMO702, SMO1002

Safety Summary

Carefully read the following safety precautions to avoid person injury and prevent damage to the instrument

and any products connected to it. To avoid potential hazards, please use the instrument as specified.

Only qualified technician should perform service procedures

To Avoid Fire or Personal Injure

Use Proper Power Line

Use only the special power line of the instrument which approved by local state.

Ground the Instrument

The instrument grounds through the protective terra conductor of the power line. To avoid electric shock, the

ground conductor must be connected to the earth. Make sure the instrument is grounded correctly before

connect its input or output terminals.

Connect the Signal Wire Correctly

The potential of the signal wire is equal to the earth, so do not connect the signal wire to a high voltage. Do

not touch the exposed contacts or components.

Look Over All Terminals’ Ratings

To avoid fire or electric shock, please look over all ratings and sign instruction of the instrument. Before

connecting the instrument, please read the manual carefully to gain more information about the ratings.

Not Operate with Suspected Failures

If you suspect that there is a damage of the instrument, please let a qualified service personnel check it.

Avoid Circuit or Wire Exposed Components Exposed

Do not touch exposed contacts or components when the power is on.

Do not operate in wet/damp conditions.

Do not operate in an explosive atmosphere.

Keep the surface of the instrument clean and dry.

User Manual SMO702, SMO1002

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

This product has been tested to the requirements of CAN/CSA-C22.2 No. 61010-1, second edition,

including Amendment 1, or a later version of the same standard incorporating the same level of

testing requirements.

Not to use the product for measurements within other measurement categories, such as CAT II, CAT

III, CAT IV.

Not to use the equipment for measurements on mains circuits, not to use the equipment for

measurements on voltage exceed the voltage range describe in the manual.

Only probe assemblies which meet the manufacturer’s specifications shall be used.

The Responsible body or operator should refer to the instruction manual to preserve the protection

afford by the equipment. If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

Any parts of the device and its accessories are not allowed to be changed or replaced, other than

authorized by the manufacturer of his agent.

Safety Terms and Symbols

Terms used on the instrument. Terms may appear on the instrument:

DANGER: Indicates an injury or hazard that may be immediately happen.

WARNING: Indicates an injury or hazard that may be not immediately happen.

CAUTION: Indicates that a potential damage to the instrument or other property might occur.

Symbols used on the instrument. Symbols may appear on the instrument:

Hazardous Protective Warning Earth Ground Power

Voltage Earth Ground Switch

User Manual SMO702, SMO1002

Digital Oscilloscopes

SMO702, SMO1002

Signal bandwidth: 70 MHz, 100 MHz

Real-time sampling rate: Max. 1 GSa/s

Equivalent sampling rate: Max. 50 GS/s

7.0” TFT LCD Color display

2 Mpts memory depth

Independent vertical scale & position control knobs for each channel

Edge, Pulse Width, Video, Slope, Alternate trigger mode

Math functions including add, Subtract, Multiply, Divide & 1024 point FFT

32 parameters of automatic measurements

Unique Digital Filter & Waveform recorder function

Advanced cursor modes: Manual, Auto & Track

Waveform Intensity & Grid Brightness can be adjusted

PASS / FAIL detection, PASS/FAIL output

Built-in 70 MHz, 100 MHz hardware frequency counter

Save/recall types: Setups, Waveforms, CSV file, Picture

Standard Interface

USB Host: Support USB flash driver save/recall function & update firmware,

USB Device: Support PictBridge compatible printer & support PC remote control, RS232,

Pass/Fail Output

User Manual SMO702, SMO1002

퐰趽惘酊숺⏆缸냅㷵껃皽

󼾉┋⟴鮝鿳

󼽌겭鑺흻틔ꅈ䪠슏屾 󰩥󼽩ﰦ삏

󼾉砉돕⧶鶟폵 󼼾ꗚл䮴

󼼞缪뭏儞䱎濄聍󰪈뒂伜荐 󼼾툚≗

퓕쉬協꩷䐑㽁䍥㉔꡵ 󼼾퉫ⱡ

󼾉┋⟴쟨 󼻏㝿ຑꈊ闩鷦헅⸦ー䰫❾究ᔑ൳󼤞㲌󼮰㰺

퓕쉬協꩷䓪䍅

󼽌㳧莅 󼻏㝫獷蟰圾撚脘尸マꧨ莈趉⠤篒藫䛱Է螵莁缂ﺩⱟ嶬⿚ീ

󼽿ㇲ拓઺퓊

󼽌㰽칟삍 󰩥󼼾틚坧욙࢛꾟잿랯

󼽌갽컧듖󼼾ꗚ⊴鼈掊໾㨆

󼼾ꖭ쑟ㄅ왶杖ꎛ

󼽌㳍幅⭸驧 󼻮й󼺏巆겘鶄駝

󼽌갽컧듖⩌᤻࡟ⲁ亢ᭉ鵪 󼼾ꗚ⊴

󼽌겓鐥ଙ浯酞豙孝㋿噘◲ 󼽊󼺇ᨢ꺾ꨥי屌

󼽊󼺇ᨢ꺾ꨥ캱Ӵ

퓕쉬協꩷䓪 󰩥󼼾툚듐鹯䄊榭距ꭂ駘ꕓꗼ揉쓀씫

퓕쉬協꩷䒏酞抐銔떏醓 󼼾툚듐鹯ݱ⌌掩畊䊁礢웂뺺뚻ↇ䧈﫸ꋕ

󼾜 閝툚듐鹯䄊榭距ꭂ駘꼔뎸뒰ᚁ紜᡾醏趋褌㹱꒟싵

퓕쉬協꩷䒏㨼酞貎꿑 閝툚듐늤䷰㋉憽要䱄Ⴛↇ佋䚬情섧䝅䉵㹱ꓗ鶴⬩岶

󼽛뮼ꢩ璖 󼽊늺⦑󼢒⠫쮫억䰞쮗﹆䞭䵉䑀ꘌ爑൳럪⇓󼼅韊

󼾉푥驢뜌ฯ兓꡵鞸蚧ꦫ"ﯽ쩰 󼽫샴ﰱ料ẇ霁튧濉䒹僨ﳉ솹蕑嬦辋蟭単붹떱᝽燴✥⌡

󼾜谝깘㼥ꇃ엦 󼼾⇓󼼎厼頔徴ᆷ쮻务󰪇猾㘁

󼼞羀󼱣ꛈ훸씚᰾ 󰩥ᐜ␬望󼠞⴬睊筫Ⱔ⇓ẽ릵넗䃠㬷㌯ᘔ隔淇엃溡 

腨ጔﬣ┧⧶␦䡪 閝틚퀄㤖羏㼑ꄰ䰠Ⓕꭂ饥嵧㋾혻㜳馞Ѐ

󼾉 󼻲 閝ꖭ䇒ꒈ󼸵犡䂽턴ꕓ䨖蟞󼧠䑀㰸㐰鮙

󼽌㰩࿎忠㐶ӑꏅ 󼽿꿤㇤컮疢 띳󼩳󰪔꾫꜃槏獯ອ陁浫黸 

󼽌겭㸫塚 󼻍㔽䗲ȥ軆얥䉖ꍑ䡀ఄ螃󼧠㮡ﴂ标뉞

󼾉 䜮霨 󼽫틚䯾㆙ׅ뵎㺻ꦡ睂ຫꞣ龛霶

󼽌갽컧듖 󼼾ꗚ⊴鼈掊໾㨆

󼼾ꖭ쑟ㄅ왶杖ꎛ

鶊焂銓Í獵矌

鶊焂銓Í玕랐 󼻮й䇪参慦敭Ꭵ 婹䒫ኋ圧ᣌ烖퉱

鶊焂銓Í鿁 󼻏㝫玧렧涸툋Ｎ峼礴Ⱬ

鶊焂銓Íיִ㽠ⷺ 󼻮й󼺏巆嵽칯ꊱ헅󼣙ӏᢑ㸊󼱹睳

鶊焂銓Í捥 󼻏㜿䟶徑䍉菼󼭤䀰쟜ꝳ⡧徫꜍猦엁붹굡3㇜󼩹୛

鶊焂銓Í슏붿ג 󼽫툆๡틢旎洿ᇢ鄲怠鶱䣰鶕䰘ᄖ浩敡워쟃⦓㹱

󼻏鏈ﱡ䞰网诨墇娨篴뾷荎ᩔ릵

鶊焂銓挊భ⿽儞󱂎 󰩥󼽭菖󼹭頼耠刺󼭚先匊⤮ ⪁䶨꒩ா 铇ᘔ䝅ꑶ왈箮

󼻏ȷ謹틮ᴤụИ蕽畭鼫󼽼휼

󼻖䖪ㅸꞗヨ〺 ๪晫節쀦

󼻏졏茖⼻ㄚ樂錸敯ⲓ䕁癲ꐀ꒩ 磏䵻移䎝冄폑Ђ憻릷

8User Manual SMO702, SMO1002

Signal Measurement

Parameters : Vpp, Vmax, Vmin, Vamp, Vtop, Vbase, Vavg, Mean, Crms,

Vrms, ROVShoot, FOVShoot, RPREShoot, FPREShoot, Rise

time, Fall time, Freq, Period, + Wid, -Wid, +Dut, -Dut, BWid,

Phase, FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF

Math Functions : Add, subtract, multiply, divide &1024 point FFT

Window : Hanning, Hamming, Blackman, Rectangular

Cursor Measurement : Manual, Auto, Track

Hardware Frequency Counter : DC Coupled, 10 Hz to Max. BW,

resolution: 1 Hz; Accuracy: ±0.01%

Storage : Internal: 2 reference waveform, 20 setup files & 10

captured waveform files

USB: Setups, Waveforms, CSV file, BMP

Interface : USB HOST, USB DEVICE, RS232C & PASS/FAIL OUT

Display System

:Display Screen : TFT LCD display, 7.0’’

Resolution : 480 ( horizontal ) x 234 (vertical) pixels

Color : 24 bit Waveform Display

Scale :8 x 18 div Storage & Interface

Type : Dots , Vector

Interpolation : (Sinx)/x, Linear

Persistence : Off, 1 sec, 2 sec, 5 sec, Infinite

General Information

Operating Condition : 10 °C to 40 °C, < 85% RH

Power : 100 – 240 V AC, CAT II, 45 Hz to 440 Hz

Power Consumption : < 50 VA

Dimension : W : 323, D : 136, H: 157 (mm)

Weight : 2.5 kg (approx.)

Accessories : Probes (2 No.s), Power cord, USB cable, Software CD, Manual

(Subject to change)

User Manual SMO702, SMO1002

Front Panel Controls

The oscilloscopes provides an easy-to-use front panel to convenience users to operate them, the panel

contains knobs and buttons. There is a list of five ashen buttons as menu operational buttons on the right

of display screen. You can set different options of the current menu in virtue of them. Other buttons are

function buttons; you can enter different function menus or obtain given function application in virtue of

them.

User Display Interface

MO 002S 1 Digital Oscilloscope 01 0MHz

1GSa/s

Option Softkeys

Menu On/Off

Universal Knob

Common Function

Horizontal Control

Auto

Button

Trigger

Control

Probe

Component

Input

Channels

Vertical

Control

Key

USB

Host

Fig. 1 Front Panel Control

Fig. 2 User Display Interface

User Manual SMO702, SMO1002

Questo manuale è adatto per i seguenti modelli

Altri manuali Scientific Apparecchiature di prova

Scientific

Scientific SMO2000X Manuale utente

Scientific

Scientific SMO502ED Manuale utente

Scientific

Scientific SME1190 Manuale utente

Scientific

Scientific SMO1000E Manuale utente

Scientific

Scientific SMO2000XP Manuale utente

Scientific

Scientific SMO5000X Series Manuale utente

Scientific

Scientific SM6030A Manuale utente

Scientific

Scientific 5000 Series Manuale utente

Scientific

Scientific SMO2000X-E Manuale utente

Scientific

Scientific SMO1000U Manuale utente

Scientific

Scientific SMO1000A-S Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente