Seagull Models Fair child PT19 Manuale utente

“Graphics and specifications may change without notice”.

MS:136

ASSEMBLY MANUAL

Specifications:

Wingspan----------------------------79.5in(202cm).

Wingarea-----------------965.7sq.in(62.3sqdm).

Weight--------------------------------11.9lbs(5.4kg).

Length------------------------------58.6in(148.8cm).

Engine ------------------ 0.91-1.2cu.in----2-stroke.

0.91-1.2cu.in ---4-stroke.

Radio-------------------6channelswith8 servos.

Retractslandinggear(included).

FAIR CHILD PT 19. Instruction Manual.

INTRODUCTION.

Thank you for choosing the PT 19 ARTF by SEAGULL MODELS. The PT 19 was designed with

the intermediate/advanced sport flyer in mind. It is a semi scale airplane which is easy to fly and

quicktoassemble.Theairframeisconventionallybuiltusingbalsa,plywoodtomakeitstrongerthan

theaverage ARTF,yet thedesign allowsthe aeroplaneto bekept light.You willfind thatmost ofthe

work has been done for you already. The motor mount has been fitted and the hinges are pre-

installed. Flying the PT 19 is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your PT 19 . Use the parts listing below to identify

all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if it is assembled or used incorrectly it

will cause injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU ASSUME

ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhiswaytosuccessful R/Cflight.Theywillalso beable

to advise on any insurance and safety regulations that may apply.

KIT CONTENTS

www.seagullmodels.com

ADDITIONAL ITEMS REQUIRED.

0.91-1.2 2-stroke.

0.91-1.2 4-stroke.

Computer radio with 8 servos.

Glow plug to suit engine.

Propeller to suit engine.

Protective foam rubber for radio

system.

Siliconefuelline.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

The control surfaces, including the

ailerons, elevators, and rudder, are

prehinged with hinges installed, but

the hinges are not glued in place. It

is imperative that you properly

adhere the hinges in place per the

steps that follow using a high-quality

thin C/A glue.

2)Removeeach hingefromthewing panel

and aileron and place a T-pin in the center of

each hinge. Slide each hinge into the aileron

untiltheT-pin is snug againsttheaileron.This

will help ensure an equal amount of hinge is

oneithersideofthe hingelinewhentheaileron

is mounted to the wing panel.

HINGING THE AILERONS .

Note:

1) Carefully remove the aileron from one

of the wing panels. Note the position of the

hinges.

Hinge.

3) Slide the aileron on the wing panel until

there is only a slight gap. The hinge is now

centered on the wing panel and aileron.

Remove the T-pins and snug the aileron

against the wing panel.Agap of 1/64” or less

shouldbemaintainedbetween the wingpanel

andaileron.

T-pin.

1 Fuselage

2 Left wing panel

3 Right wing panel

4 Tail set (2)

5 Pilot (2)

6 Aluminum wing tube

7 Fiberglass cowl

8 Retracts landing gear

9 wheels (2)

10 Hardware bag included

KIT CONTEN.TS

FAIR CHILD PT 19. Instruction Manual.

8)Afterbothailerons aresecurelyhinged,

firmly grasp the wing panel and aileron to

make sure the hinges are securely glued and

cannot be pulled out. Do this by carefully

applying medium pressure, trying to separate

the aileron from the wing panel. Use caution

not to crush the wing structure.

7) Repeat this process with the other wing

panel, securely hinging the aileron in place.

6) Using C/A remover/debonder and a

papertowel,removeany excessC/Agluethat

may have accumulated on the wing or in the

aileronhingearea.

5)Turnthe wing paneloverand deflect the

aileron in the opposite direction from the

opposite side. Apply thin C/A glue to each

hinge,makingsurethattheC/Apenetratesinto

both the aileron and wing panel.

Workthe aileronup anddown several

times to “work in” the hinges and

check for proper movement.

Note:

4) Deflect the aileron and completely

saturate each hinge with thin C/A glue. The

aileronsfrontsurface shouldlightlycontact the

wing during this procedure. Ideally, when the

hinges are glued in place, a 1/64” gap or less

will be maintained throughout the lengh of the

aileron to the wing panel hinge line.

Thehingeis constructedof aspecial

material that allows the C/A to wick

or penetrate and distribute

throughout the hinge, securely

bonding it to the wood structure of

the wing panel and aileron.

Note:

Hinge.

www.seagullmodels.com

Aileroncontrolhorn.

INSTALL THE AILERONS CONTROL

HORN.

1) Locate the hardware necessary to install

the control horns for the ailerons.

2) Position the control horn on the bottom of

the aileron. You will see pre-drill hole 3mm for

the horn mounting screw on the aileron.

3) Place epoxy into hole. This will harden the

threads and prevent the crews from pulling

loose.

4) Thread a control horn end with aluminum

washer, lock nut until the top edge of the end is

18mm from the vase of the horn as shown.

3mm.

HINGING THE RUDDER.

Glue the rudder hinges in place using the

same techniques used to hinge the ailerons.

Hinge.

HINGING THE ELEVATOR.

Glue the elevator hinges in place using the

same techniques used to hinge the ailerons.

C/Aglue.

ALUMINUMWASHER.

CONTROLHORN

M3 SCREW.

18mm.

Epoxy.

Wing

Epoxy.

M3LOCKNUT.

2 sets.

3x35mm.

FAIR CHILD PT 19. Instruction Manual.

Install the flap control horn using the same

methodas sameas theaileroncontrol horns.

INSTALL FLAP CONTROL HORN.

2 sets.

3x30mm.

Aluminum Washer.

CONTROLHORN

M3 SCREW.

M3LOCKNUT.

Epoxy.

Aluminum Washer.

Flap.

CONTROLHORNM3SCREW.

M3 lock nut.

ALUMINUMWASHER. 18mm.

ALUMINUMWASHER.

Epoxy.

Flap.

M2x6mm.

Screw.

www.seagullmodels.com

3mm.

Flap control horn.

Install the elevator control horn using the

same method as same as the aileron control

horns.

INSTALL ELEVATOR CONTROL HORN.

2 sets.

3x35mm.

AluminumWasher.

CONTROLHORNM3

M3LOCKNUT.

Epoxy.

AluminumWasher.

Horizontal

Stabilizer. Elevator.

M2x6mm.

Screw.

1.5mm.

FAIR CHILD PT 19. Instruction Manual.

Thread locker glue.

ENGINE MOUNT INSTALLATION.

1) Locate the items necessary to install the

engine mount included with your model.

2) Usefour4x30mm headboltsandfour 4mm

washers to attach the engine mount rails to

thefirewall.Tightenthescrews. Make sure to

use threadlock on the screws to help prevent

them from vibrating loose.

4x30mm.

INSTALL RUDDER CONTROL HORN.

3mm.

Repeat steps to install the rudder control

horn as same as steps done for ailerons.

Ruddercontrolhorn.

Elevator control horn.

veticalfin.

18mm.

Epoxy.

Horizontal

Stabilizer. Elevator.

www.seagullmodels.com

3) Carefully bend the second nylon tube

up at a 45º angle. This tube is the vent tube.

4) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using a

modeling knife. If flashing is present, make

sure none falls into the tank.

Venttube. Fuel pick up tube.

Fuel fill tube.

Plywood template.

1) Using a modeling knife, carefully cut

off the rear portion of one of the 3 nylon tubes

leaving 1/2” protruding from the rear of the

stopper. This will be the fuel pick up tube.

INSTALLING THE STOPPER ASSEMBLY.

2) Usingamodelingknife,cut one length

ofsiliconfuelline. Connect oneendofthe line

totheweightedfuelpick up and theotherend

to the nylon pick up tube.

5) With the stopper assembly in place,

the weighted pick-up should rest away from

therearofthetankandmovefreelyinsidethe

tank. The top of the vent tube should rest just

below the top of the tank. It should not touch

the top of the tank.

6) When satisfied with the alignment of

the stopper assembly tighten the 3 x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not

overtighten the assembly as this could cause

the tank to split.

FUEL TANK INSTALLATION.

You should mark which tube is the vent

and which is the fuel pickup when you attach

fuel tubing to the tubes in the stopper. Once

thetankisinstalledinside the fuselage, itmay

be difficult to determine which is which.

FAIR CHILD PT 19. Instruction Manual.

THROTTLE SERVO ARM INSTALLATION.

Installadjustableservoconnectorinthe servo

arm as same as picture below:

AdjustableServo

connector.

Servoarm.

Loctite secure.

1PCS.

Throttleservoarm.

Elevatorservoarm.

Rudderservoarm.

INSTALLING THE FUSELAGE SERVOS.

1) Installtherubbergrommetsand brass

colletsontothe throttleservo. Testfitthe servo

into the aileron servo mount.

 2) Secure the servos with the screws pro-

vided with your radio system.

Because the size of servos differ, you

mayneedtoadjustthesizeoftheprecutopen-

ing in the mount. The notch in the sides of the

mount allow the servo lead to pass through.

Throttle servo.

Elevator servo.

Rudder servo.

 7) Slide the fuel tank into the fuselage. Guide

the lines from the tank through the hole in the

firewall.

Fueltank.

Epoxy.

Fueltank.

 8) Use plywood template to hold in place

the fuel tank with C/A glue to secure the fuel

tank inside the fuselage.

Plywood template.

Venttube.

Fuel pick up tube.

Fuel fill tube.

Blow through one of the lines to en-

sure the fuel lines have not become kinked

inside the fuel tank compartment. Air

should flow through easily.

Indice

Altri manuali Seagull Models Giocattolo

Seagull Models

Seagull Models Little Bunnt P-47D Manuale utente

Seagull Models

Seagull Models AT-6 TEXAN Manuale utente

Seagull Models

Seagull Models Silence Twister Manuale utente

Seagull Models

Seagull Models SEA238 Manuale utente

Seagull Models

Seagull Models EXTRA EA 300L Manuale utente

Seagull Models

Seagull Models TEMPEST DRAGON 15cc ARF Manuale utente

Seagull Models

Seagull Models Cessna L-19A Bird Dog Manuale utente

Seagull Models

Seagull Models EDGE 540 Manuale utente

Seagull Models

Seagull Models SEA 324Y Manuale utente

Seagull Models

Seagull Models BEAVER TURBIN Manuale utente

Seagull Models

Seagull Models CAP 232 Manuale utente

Seagull Models

Seagull Models CURTISS P-40N WARHAWK Manuale utente

Seagull Models

Seagull Models Turbo Raven Manuale utente

Seagull Models

Seagull Models Piper Cub Manuale utente

Seagull Models

Seagull Models SEA EAGLE Manuale utente

Seagull Models

Seagull Models P-47D Thunderbolt 60 Manuale utente

Seagull Models

Seagull Models Extra 300S Manuale utente

Seagull Models

Seagull Models ANGEL GLIDER 2000 Manuale utente

Seagull Models

Seagull Models Mini Sparrowhawk EP Manuale utente

Seagull Models

Seagull Models Arising Star Manuale utente

Seagull Models

Seagull Models Extra 260 Manuale utente

Seagull Models

Seagull Models THUNDERBOLT P47G SNAFU 60 ARF Manuale utente

Seagull Models

Seagull Models JU-87 STUKA GIANT SCALE Manuale utente

Seagull Models

Seagull Models YAK 54 Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente

Seagull Models fair child PT19 Manuale utente

Manuali Giocattolo popolari di altre marche