SeeMeCNC Orion delta Manuale utente

Orion Delta™ 3D Printer Manual

Second Edition – Firmware 0.91 and Higher

1.31, September 28th, 2016

Licensed as Creative Commons, Attribution-ShareAlike 3.0

This guide will take you through the steps to set up and operate your new 3D

printer from SeeMeCNC. You’ll find instructions on calibration, software, maintenance

and more all in this manual. As a new SeeMeCNC™ owner, you’ll also find a ton of great

resources on the forums at forum . seemecnc . com

Introduction – Read Me First!

This document is your instruction manual for your new SeeMeCNC® 3D printer machine.

Before using your new 3D printer thoroughly read and understand this manual for safe and

effective operation of the machine.

Warning

Adult supervision required. Children under 18 years of age require supervision.

Risk of Fire. Do not leave machine unattended.

Use genuine parts manufactured or designated y SeeMeCNC.

Keep a copy of this manual near the machine, easily accessi le to all operators.

Use of this machine is at your own risk.

Personal property damage, serious injury or death can result from not following

instructions or warning in the manual or misuse of the machine.

Automatic machine can start unexpectedly. Pay close attention and keep clear

while power is connected to the machine

The machine power supply is connected to AC voltage

and can e hazardous. Disconnect power efore

servicing this machine.

The hot end of the machine can reach very high

temperatures of 700F and can cause serious urns.

The heated print surfaces (heated ed) can also reach

temperatures high enough to cause severe urns. Allow

oth to cool for 20 minutes after turning off power.

Use caution near moving parts of the machine. Keep

ody and loose articles clear.

Poisonous gas, smoke, or fumes could e emitted y some materials you could

use with the machine. In such case, you should install ventilation.

Choking Hazard. This machine contains small parts and

can produce small parts which can e a choking hazard

to children.

Visit http://www.seemecnc.com to contact us if you have any questions.

Table of Contents

Un-Boxing your new Orion Delta™ 3D Printer.............................................................................4

Installing the LCD Control Panel USB Cable and SD Card.........................................................7

Installing the Power Cord and Spool Holder..............................................................................12

Loading Filament.......................................................................................................................16

Powering Up your new Orion Delta™ 3D Printer for the First Time............................................19

The LCD Control Panel..............................................................................................................20

Setting the Z height.................................................................................................................... 23

Leveling your new Orion Delta™ 3D (The Easy Way!)...............................................................25

A Simple Guide to Hot End Priming...........................................................................................31

Printing from the SD Card..........................................................................................................33

Changing Filament.....................................................................................................................36

Printing From Your Computer.....................................................................................................39

Advanced Repetier-Host............................................................................................................56

Attention! If your Orion Delta™ has a serial number of 100169 or

less you may need to download the First Edition of the user

guide here:

http://www.geneb.org/orion/O RIONUserManual.pdf

The First Edition covers the older firmware that originally shipped

with the Orion Delta™ 3D printer.

Before downloading the First Edition please make sure that you

actually need it. Compare the LCD idle screen (shown on power-on

after the initialization sequence takes place) on your machine to the

first LCD screen photo shown in the “The LCD Control Panel” chapter.

If they match you've got the newer firmware and do not need the

second edition. You can follow this edition to reach the power-on

point in order to definitively identify which firmware your machine

was shipped with.

Un-Boxing your new Orion Delta™ 3D Printer

With your box standing in the upright position carefully cut the packing tape along the

top edges and across the taped seam in the box.

After you’ve cut the tape open the top of the box being careful of any packaging staples.

You’ll find the machine tucked inside and wrapped in a protective expanding foam shell.

Remove the machine and foam all as one by pulling straight up out of the box. Be careful not to

drop the machine once it’s out of the box and the foam is still around it.

Carefully cut and remove the stretch wrap film that is holding the power/USB cables

Orion control panel and accessories on the top plate as well as the stretch wrap holding your

filament to the table top and glass build surface.

In order to prevent damage during shipping the hot end on the Orion Delta™ is locked in

place over the bed by lowering the delta arms as low as they'll go on each tower. These arms

need to be raised in order for the Orion Delta™ to be used.

The process is very simple – just grasp the Cheapskate bearing for each arm and raise

them one at a time to the top of the Orion as shown in the photos below.

Installing the LCD Control Panel USB Cable and SD Card

Note that the blue acrylic face plate on your Orion Delta™ will likely differ from the

photos shown here but the installation instructions are identical.

Gently pull the pair of flat ribbon cables out a bit from the Orion Delta™ and install them

as shown. The “first” cable is marked by an “X” and has a matching “X” on the back of the LCD

controller.

The USB cable only needs to be used if you wish to manually control the machine from

the software on your PC. You can print and do most calibration standalone without the USB

cable attached. We recommend hooking it up now so if you need to connect it to your

computer to make changes etc. the cable is already installed.

Pass the end of the USB cable up through the hole in the bottom left of the base and

plug it into the USB input on the electronics board.

Next replace the front panel by putting the bottom in first then tilting the top in. Please

be careful as it’s a tight fit. Re-install the two black thumb screws and tighten them finger tight.

Remove the two black thumb screws as shown and set them aside.

Now you'll install the LCD control panel into the Orion Delta™. Please take care as the

parts are a tight fit. Align the LCD mounting plate as shown below – there's small locking tabs

that fit into the slots shown.

Carefully raise the panel into place and fit it flush against the mating surface making

sure that not wires get pinched between the two panels – this is a tight fit so please be careful.

Insert the black thumbscrews you'd removed earlier in the mounting holes and tighten

them using only your fingers.

Altri manuali per orion delta

Indice

Altri manuali SeeMeCNC Stampante 3D

SeeMeCNC

SeeMeCNC Delta Manuale utente

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manuale utente

SeeMeCNC

SeeMeCNC DropLit Manuale utente

SeeMeCNC

SeeMeCNC Artemis Manuale utente

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manuale utente

SeeMeCNC

SeeMeCNC ERIS DELTA Manuale utente

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manuale utente

SeeMeCNC

SeeMeCNC Artemis 300 Manuale utente

SeeMeCNC

SeeMeCNC Rostock MAX v2 Manuale utente

SeeMeCNC

SeeMeCNC orion delta Manuale utente

SeeMeCNC

SeeMeCNC rostock max v2.0 Manuale utente

SeeMeCNC

SeeMeCNC Rostock Max v3 Manuale utente

SeeMeCNC

SeeMeCNC Rostock Max Manuale utente

SeeMeCNC

SeeMeCNC Rostock Max v3 Manuale utente

SeeMeCNC

SeeMeCNC orion delta Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente