Senior Technologies WanderGuard 18029 Manuale utente

Read these instructions, particularly the Warnings and Cautions,

before using the WanderGuard®Universal Tester. Failure to do

so could result in injury or death to a person in your care.

WARNING

Operating Instructions

WanderGuard®Universal Tester

Model 18029

0163-390

FCC ID:LA5IDUT001

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: 1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by Stanley Senior

Technologies could void the user's authority to operate the equipment.

All content herein is the property of The Stanley Works, its Affiliates, or their

content suppliers and is protected by United States and international copyright

laws. The compilation of all content is likewise the exclusive property of The

Stanley Works (or the Affiliate identified in any copyright notice) and is protected

by United States and international copyright laws.

The trademarks, service marks and logos (the 'Trademarks') used and displayed

in this publication are registered and unregistered Trademarks of The Stanley

Works, its Affiliates and others. Nothing herein should be construed as granting,

by implication, estoppel or otherwise, any license or right to use any Trademark

displayed herein without the prior consent of the Trademark owner. ARIAL,

AUTISM ALLY, AUTISM ALLY design, the CATCH-ALL design, SENIOR

TECHNOLOGIES, TABS, TIM, WANDERGUARD, and the WANDERGUARD

design are some of the registered and unregistered trademarks owned by The

Stanley Works and/or its Affiliates ("Stanley Trademarks"). Stanley Trademarks

may not be used in connection with any product or service that is not

manufactured by or under license from The Stanley Works or its appropriate

Affiliate.

Test bracelets daily as detailed in these instructions, in the

bracelet instructions, and the WanderGuard®Door Monitor User

Manual. Record the results in the resident’s records. It is

important to test the bracelet before putting it into use and daily

thereafter. Failure to do so could result in injury to or death to a

person in your care.

WARNING

Dispose of the Universal Tester immediately when low battery is

indicated on the display.

When testing the bracelet, make regular inspections to check for

frayed or loose bands.

Stanley-Senior Technologies recommends the removal of the

bracelet during x-ray or MRI procedures.

Changes or modifications not expressly approved by Stanley-

Stenior Technologies could void the user’s authority to operate

the equipment.

CAUTION

Features of the WanderGuard®Universal Tester

The Universal Tester is a hand-held, battery-powered device used to test

WanderGuard door monitors and WanderGuard bracelets.

When using the tester to test bracelets, the tester will detect if a bracelet

is working properly, the individual ID number of the resident wearing

the bracelet and when the bracelet is reaching its “replace bracelet”

date.

The Universal Tester will indicate when it’s battery life is low. When

the battery power is low, “LO” will flash three times whenever a button

is pressed. When this happens, the Universal Tester needs to be replaced

immediately. The tester is guaranteed to operate for at least one year*. A

dimming display is also an indication that the battery is low and the

tester needs to be replaced.

The Universal Tester has an ambient light sensor built-in. When the

tester is used in low light conditions, it will automatically back-light the

LCD display.

Using the RECALL button will display the result of the last bracelet

test.

DOOR

TEST

BRACELET

TEST

RECALL

AMBIENT LIGHT

SENSOR

* Based on testing 30 bracelets and 10 doors per day.

Testing Door Monitors

The Universal Tester will test all WanderGuard®door monitors except the

FirstQTM series. Test door monitors at least weekly on each shift with all

surrounding power devices turned on to maximize possible

electromagnetic interference. If using a PIR device, refer to the

instructions that are shipped with it.

To test a WanderGuard door monitor that has WanderGuard®System

Status Display installed:

1. Open the door(s).

2. Move to 3' in front of the middle of the door, or middle of doorway if

testing a double door system, and hold the tester at waist level.

3. Press the DOOR button. The LED above the button will turn on and

segments on the LCD display will animate indicating the tester is

transmitting. “??????” will be displayed on the System Status Display.

(A single button press activates the tester for 2 seconds, or the button

can be held down to transmit continuously.)

4. Repeat Steps 2 and 3, holding the tester at ankle, knee, and head level.

5. Move to the right side of the door and repeat Steps 2 through 4.

6. Move to the left side of the door and repeat Steps 2 through 4.

To test a WanderGuard door monitor WITHOUT a WanderGuard®

System Status Display installed:

1. Open the door(s).

2. Move to 3' in front of the middle of the door, or middle of doorway if

testing a double door system, and hold the tester at waist level.

3. Press the DOOR button. The LED above the button will turn on and

segments on the LCD display will animate indicating the tester is

transmitting. The alarm on the door monitor will sound. Reset the

alarm. (A single button press activates the tester for 2 seconds, or the

button can be held down to transmit continuously.)

4. Repeat Steps 2 and 3, holding the tester at ankle, knee, and head level.

5. Move to the right side of the door and repeat Steps 2 through 4.

6. Move to the left side of the door and repeat Steps 2 through 4.

If the alarm does not sound, make sure the door is open and the tester is

within 3' of the monitor. If the alarm still does not sound, contact Senior

Technologies’ Technical Service at 800-824-2996.

Testing Bracelets

“End of Service” feature

Bracelet Model 36000 has an “End of Service” feature. During routine

testing the Universal Tester will display when the bracelet is reaching

the end of its useful service. This lets you know it is time to replace the

bracelet BEFORE the bracelet becomes inoperable. Bracelets must be

tested daily. IMPORTANT: Failure to replace the bracelet “on time”

could result in injury to or the death of a person in your care.

To test a WanderGuard bracelet with ID capability

(Model number 36000):

1. Hold the Universal Tester within one foot of the bracelet.

2. Press the BRACELET button once. The LED above the button will

turn amber.

3. If the bracelet is still operational, the LED will turn green and the

ID number of the bracelet will be displayed.

4. If the bracelet has reached the End-of-Service phase, the LED will

flash red.

5. If the bracelet is not detected, the LED will flash red twice and

display “- - -”.

If the Universal Tester does not detect the bracelet:

• Move the tester closer to the bracelet.

• Hold the tester at a different orientation in relation to the bracelet.

• ‘Sweep’ the tester by the bracelet.

To test a WanderGuard bracelet WITHOUT ID capability

(Model numbers 32xxx, 32xxx, and 32xxx):

1. Hold the Universal Tester within one foot of the bracelet.

2. Press the BRACELET button once. The LED above the button will

turn amber.

3. If the bracelet is still operational, the LED will turn green and

“000” will be displayed.

4. If the bracelet has reached the End-of-Service phase, the LED will

flash red.

5. If the bracelet is not detected, the LED will flash red twice and

display “- - -”.

If the Universal Tester does not detect the bracelet:

• Move the tester closer to the bracelet.

• Hold the tester at a different orientation in relation to the bracelet.

• ‘Sweep’ the tester by the bracelet.

For assistance, please call Stanley-Senior Technologies at

800-824-2996 or 402-475-4002

Mailing address: Stanley-Senior Technologies • P. O. Box 80238

Lincoln, NE 68501-0238

Shipping address: Stanley-Senior Technologies• 1620 N. 20th

Lincoln, NE 68503-1103

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente