SGS electronic TVC-TRF-10-MBT Manuale utente
TVC-TRF-10-MBT
1
© SGS electronic 2006-2021
TVC-TRF-10-MBT
Full option module with sound for RC-battle tanks in
1/16th to1/25th scale
This module was developed to enable complete control of battle tanks.
TVC-TRF-10-MBT
2© SGS electronic 2006-2021
1 Note
Installation of the module requires intermediate to advanced modeling skills.
Soldering skills are required to connect the wiring. Inexperienced modelers and
persons under 16 should seek the assistance of an experienced modeler.
Always switch off power when working on the wiring.
Especial take care when connecting more than one receiver energy source.
Prevent the device from getting wet.
Check loads before connecting them to the modul at a current limited, or
fuse protected source.
TVC-TRF-10-MBT
3
© SGS electronic 2006-2021
Contents
1 Note 2
2 Introducing 6
2.1 FOmodulfeatures............................ 6
2.2 technology ................................ 7
2.3 scopeofdelivery............................. 7
2.4 accessories ................................ 7
2.5 Overview.................................. 7
2.5.1 build in functions . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5.2 Additional options . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 Radiorequirements ........................... 9
2.6.1 usableradios........................... 9
2.6.2 bestpractice........................... 9
3 functions 11
3.1 Manualcontrol.............................. 11
3.1.1
Channel 1 - Proportional left/right with integrated V-mixer
11
3.1.2 Channel 2 - Proportional forward/reverse . . . . . . . . . 11
3.1.3 Channel 3 - Proportional cannon elevation / gun trigger 11
3.1.4 Channel 4 Proportional turret rotation . . . . . . . . . . . 11
3.1.5 Channel 5 Controlling the light mode . . . . . . . . . . . . 12
3.1.6
Channel 6 turn model off / change model / activate turret
stabilization ........................... 12
3.1.7 Channel 7 Controlling the volume . . . . . . . . . . . . . . 12
3.1.8 Channel 8 firing . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Function of the light mode control . . . . . . . . . . . . . . . . . . 13
3.2.1 Lightmode1........................... 13
3.2.2 Lightmode2........................... 14
3.2.3 Tip2................................ 15
3.3 Automaticfunctions........................... 15
3.3.1 cannon .............................. 15
3.3.2 MG................................. 15
3.3.3 automatic engine stop . . . . . . . . . . . . . . . . . . . . . 15
3.4 drive-dynamic functions . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4.1 Exhaust simulation module . . . . . . . . . . . . . . . . . . 16
3.4.2 Reverselight........................... 16
3.4.3 Rotating flasher light . . . . . . . . . . . . . . . . . . . . . . 16
3.4.4 Turnsignals ........................... 16
TVC-TRF-10-MBT
4© SGS electronic 2006-2021
3.4.5 Brakelight ............................ 17
4 Connector overview 18
4.1 Connection of batteries cable (X60) . . . . . . . . . . . . . . . . . . 18
4.2 connection to the receiver (X50 to X511) . . . . . . . . . . . . . . 19
4.3 connection of the servo outputs (X40 to X47) . . . . . . . . . . . . 20
4.3.1 Connect the turret turn servo . . . . . . . . . . . . . . . . . 20
4.3.2 Connect the cannon elevation servo . . . . . . . . . . . . . 21
4.3.3 Connect the recoil servo . . . . . . . . . . . . . . . . . . . . 21
4.4 connection of the motors (X01 - X04 & X20 - X21) . . . . . . . . . 21
4.5 connection of drive motors . . . . . . . . . . . . . . . . . . . . . . . 22
4.5.1 Connect the turret turn motor . . . . . . . . . . . . . . . . 22
4.5.2 Connect the cannon elevation motor . . . . . . . . . . . . 22
4.6 connection of the switch outputs (X08 to X17) . . . . . . . . . . . 22
4.6.1 Connection of lighting and exhaust systems . . . . . . . . 23
4.7 Connecting the speaker (X70) . . . . . . . . . . . . . . . . . . . . . 24
4.8 Connecting the battle unit (X510 and X511) . . . . . . . . . . . . . 25
5 Initialization 27
5.1 turnonsequence ............................ 27
5.2 operationmodes............................. 27
6 changing sound and software 28
6.1 Changingthesound........................... 28
6.2 Changing the software . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3 Battleunit ................................. 29
6.3.1 Vulnerably ............................ 29
6.3.2 Resetting the damage grade . . . . . . . . . . . . . . . . . 30
7 Practical tips 32
7.1 Neutralposition ............................. 32
7.2 Failsafereceiver ............................. 32
7.3 Do not use provisionally methods of connectivity . . . . . . . . . 32
7.4 Workonthewiring ........................... 32
7.5 Rotatingflasher ............................. 33
7.6 ConnectingLED ............................. 33
8 Glossary of terms 35
9 Technical data 36
10 Important 37
TVC-TRF-10-MBT
5
© SGS electronic 2006-2021
10.1Address .................................. 37
10.2Contact .................................. 37
10.3Documentdate.............................. 37
List of Figures
1 connectoroverview ........................... 18
2 battery cable shown with polarity . . . . . . . . . . . . . . . . . . . 19
3 servo connector signals . . . . . . . . . . . . . . . . . . . . . . . . . 19
4 orientation servo input cables to the receiver . . . . . . . . . . . . 19
5 Futaba servos have a plastic nozzle that has to be removed . . . 20
6 orientation servo output cables . . . . . . . . . . . . . . . . . . . . 20
7 example mechanic tor recoil and elevation . . . . . . . . . . . . . 21
8 motorconnectors ............................ 22
9 switchoutputs .............................. 23
10 speakerconnector............................ 24
11 TVC-BU12................................. 25
12 TVC-HRF-AD3 Heng Long adapter mounted on the FO module . 26
13 position and orientation of the µSD card slot . . . . . . . . . . . . 28
14 rotating flasher wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 33
15 LEDresistor................................ 34
16 resistor for LED groups . . . . . . . . . . . . . . . . . . . . . . . . . 34
List of Tables
1
Overview control channels. abbrevations refer to table 9 on page
35. ..................................... 13
2 Lightmode1 ............................... 13
3 Lightmode2 ............................... 14
4 overview turret connections . . . . . . . . . . . . . . . . . . . . . . 21
5 Allocation of terminal posts for the lights, exhaust fan, and heater 24
6 boot-loader error codes . . . . . . . . . . . . . . . . . . . . . . . . 29
7 vulnerably depending on model type . . . . . . . . . . . . . . . . 30
8 delay used by the battle unit . . . . . . . . . . . . . . . . . . . . . . 31
9 Abbrevation for the manipulators in the transmitter housing . . 35
TVC-TRF-10-MBT
6© SGS electronic 2006-2021
2 Introducing
This modul for recovery tanks is based on our 3th generation of the full option
modul. This module comes with a wide range of in- and outputs and is therefore
suitable for a wide varety of models. The user can switch the function between
any of the model types just by loading the software provided on our website
• Trucks
trailer trucks
tank transporter trucks
spezial function trucks
• construction machines
dumper trucks
hydraulic excavators
rope excavators
dozers
• tanks
main battle tanks mbt/pso
recovery tanks
anti aircraft tanks
armored person carrier
excavator tanks
amphibious tanks
• snow forming tracked vehicles
• tugs
2.1 FO modul features
•
6 integrated ESC with a drive capability of 2x10A and 4x3A, clocked with
16kHz
•
audio subsystem with 15W amplifier , volume can be controlled by a
trimmer or a rc chanel
• 20 light output chanels
• 8 servo outputs
• 4 inputs for sensors (e.g. gepard radar parking pos sensor)
• maximum control chanel count is 16; PPM, S-Bus, I-Bus are supported
•
sounds and firmware can be loaded using a uSD card to change the
TVC-TRF-10-MBT
7
© SGS electronic 2006-2021
modules function to all kind of model software we provide
2.2 technology
The controller is rated for an input of 7.2V to 16V. A 10A fuse protects the
module and the battery from over current. Integrated fail safe functions prevent
unintended operation of the model.
An internal BEC generates 5V to supply the receiver. The receiver is supplied
through the servo cables. The modul internally operates with 3.3V.
2.3 scope of delivery
Connecting cables and plugs are supplied with the module, which must be
connected/soldered on the load side:
• servo leads for receiver connection
• green connector for power supply X60
• black connector for speaker X70
• black connectors for X01 to X04, X20 and X21
2.4 accessories
Connecting cables for outputs X08 to X17 (light, smoke generator, etc.) are NOT
included in the delivery. These outputs can be used with standard three-pin
servo leads. We offer different contacting options for this in the accessories.
•FO-LS10
universal cable set with 8 servo leads, cable ties and 8 series
resistors for LED
•FO-AD13 universal adapter with contact spring force clamps
•TVC-TRF-AD4
Adapter for connectors of the electrical system in Tamiya
truck models
2.5 Overview
2.5.1 build in functions
This module will provide the following functions:
TVC-TRF-10-MBT
8© SGS electronic 2006-2021
• proportional drive motor control with mixing
•
proportional turret rotation with servo output or integrated speed con-
troller
•
proportional barrel elevation with servo output or integrated speed con-
troller
• cannon fire and recoil with strobe LED flash and motor or servo output
• MG-LED
•
polyphonic sounds for all functions (including motor , MG, turret rotation,
gun)
• random sounds
•
automatic control of brake light, reverse light, flashing light, light control
can be changed by RC-channel
• battle-unit function (Tamiya compatible)
•
model change (up to three models can be controlled with one transmitter)
• automatic control of smoke pump and heating element
2.5.2 Additional options
With an additional module, TVC-GSU12, the turret can be stabilized in horizontal
and vertical direction.
For endless turret rotation, wiring can be eliminated by using GFMC-SBR10
scalebus repeater. In this case the turret drives and lights are connected to TVC-
GSU-12 (with stabilization) or turret control TVC-TC12 (without stabilization).
TVC-TRF-10-MBT
9
© SGS electronic 2006-2021
2.6 Radio requirements
2.6.1 usable radios
All common FM and 2.4GHz RC radios are supported. No special functions or
mixers are required in the transmitter. The simpler the radio, the easier the
commissioning.
In order to be able to control as many variants as possible, some functions of
the FO module work by storing operation modes or by differentiate the speed
of with which the stick is moved from the middle position.
For channels operating this way it is important that they are triggered starting
from the middle position.
This is for non-self-resetting channels, like
1. linear knobs
2. rotary knobs
3. non self centering sticks (throttel chanel for RC planes)
not automatically the case. An operation of the above functions should be done
with
1. three stage momentary switch
2. self centering sticks
.
In table 1 you can find the suggest kind of control elements for each chanel.
Note
Not self centering control elements must be placed in mid position
befor turning on the FO Modul.
2.6.2 best practice
We recommend testing the channels of your radio before installing the module.
Most radios today have their focus on operating RC planes. Control elements
are often not (all) intended to directly output their switching state. Their primary
task in flight radios is to manipulate the function / parameters of the mixers
built into the transmitter.
The failsafe function (if available) should be set to output the mid position
of all chanels.
TVC-TRF-10-MBT
10 © SGS electronic 2006-2021
The transmitter should not be set on the FO module. The servo travel in-
dicator on the transmitter display is more suitable, or a test setup with servos
connected directly to the receiver.
You can observe the following behavior:
1.
on a self centering stick a servo follows the movement of the stick. If you
let the stick go, the servos moves to mid position.
2.
having a linear or rotary knob on the chanel a servo follows the movement
and stays their even after untouching the control element
3.
with a three stage switch a servo can be moved to three positions. left,
mid, right. As the switch don’t move if you let him go, the servo will not
move also.
4.
using a three stage momentary switch a servo can also the moved to three
positions, mut it returns to mid after releasing the switch.
Indice
Altri manuali SGS electronic Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
