Siemens 6ES7134-4FB51-0AB0 Manuale utente
SIMATIC ET 200S distributed I/O 2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
Preface
Properties
1
Parameters
2
Diagnostics
3
Analog value representation
4
Connecting
5
SIMATIC
ET 200S distributed I/O
2AI U HS analog electronic module
(6ES7134-4FB51-0AB0)
Manual
04/2007
A5E01076015-01
Safety Guidelines
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
WARNING
This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY
Ordernumber: A5E01076015-01
Ⓟ 11/2007
Copyright © Siemens AG 2007.
Technical data subject to change
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
Manual, 04/2007, A5E01076015-01 3
Preface
Preface
Purpose of the manual
This manual supplements the
ET 200S Distributed I/O System
Operating Instructions.
General functions for the ET 200S are described in the
ET 200S Distributed I/O System
Operating Instructions.
The information in this document along with the operating instructions enables you to
commission the ET 200S.
Basic knowledge requirements
To understand these operating instructions you should have general knowledge of
automation engineering.
Scope of the manual
This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.
Recycling and disposal
Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable. For
environmentally compliant recycling and disposal of your electronic waste, please contact a
company certified for the disposal of electronic waste.
Additional support
If you have any questions relating to the products described in these operating instructions,
and do not find the answers in this document, please contact your local Siemens
representative.
http://www.siemens.com/automation/partner
The portal to our technical documentation for the various SIMATIC products and systems is
available at:
http://www.siemens.com/automation/simatic/portal
The online catalog and ordering system are available at:
http://www.siemens.com/automation/mall
Preface
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
4 Manual, 04/2007, A5E01076015-01
Training center
We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in D -
90327, Nuremberg, Germany.
Phone: +49 (911) 895-3200.
http://www.siemens.com/sitrain
Technical Support
You can reach technical support for all A&D projects
● using the support request web form:
http://www.siemens.com/automation/support-request
● Phone: + 49 180 5050 222
● Fax: + 49 180 5050 223
For more information about our technical support, refer to our Web site at
http://www.siemens.de/automation/service
Service & Support on the Internet
In addition to our documentation services, you can also make use of our comprehensive
online knowledge base on the Internet.
http://www.siemens.com/automation/service&support
There you will find:
● Our Newsletter, which constantly provides you with the latest information about your
products.
● The right documentation for you using our Service & Support search engine.
● The bulletin board, a worldwide knowledge exchange for users and experts.
● Your local contact for Automation & Drives in our contact database.
● Information about on-site services, repairs, spare parts. Lots more can be found on our
"Services" pages.
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
Manual, 04/2007, A5E01076015-01 5
Table of contents
Preface ...................................................................................................................................................... 3
1 Properties .................................................................................................................................................. 7
1.1 2AI U HS analog electronic module (6ES7134-4FB51-0AB0).......................................................7
2 Parameters.............................................................................................................................................. 11
2.1 Parameters...................................................................................................................................11
2.2 Parameter description..................................................................................................................12
3 Diagnostics.............................................................................................................................................. 13
3.1 Diagnostics using LED display.....................................................................................................13
3.2 Error types....................................................................................................................................14
3.3 Interrupts......................................................................................................................................14
4 Analog value representation .................................................................................................................... 15
4.1 Introduction ..................................................................................................................................15
4.2 Analog value representation for measuring range with SIMATIC S7 ..........................................15
4.3 Measuring ranges ........................................................................................................................16
4.4 Effect on analog value representation .........................................................................................17
4.4.1 Effect of the supply voltage and the operating state on analog input values ..............................17
4.4.2 Effect of the value range on the 2AI U HS analog input ..............................................................18
5 Connecting .............................................................................................................................................. 19
5.1 Connecting measuring sensors ...................................................................................................19
5.2 Wiring unused channels of the analog input modules.................................................................22
5.3 Using the shield connection .........................................................................................................22
Index........................................................................................................................................................ 23
Table of contents
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
6 Manual, 04/2007, A5E01076015-01
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
Manual, 04/2007, A5E01076015-01 7
Properties 1
1.1 2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
Properties
● 2 inputs for measuring voltage
● Input ranges:
± 10 V, resolution 13 bits + sign
± 5 V, resolution 13 bits + sign
± 2.5 V, resolution 13 bits + sign
1 V to 5 V, resolution 13 bits
● Isolated from the load voltage L+
● Permissible common mode voltage 100 VACSS
● Supports isochronous operation
– Minimum time for the synchronous DP cycle (TDPmin): 2.5 ms
– Minimum conversion time of the input modules (TWEmin): 1.1 ms
General terminal assignment
Note
Terminals 4, 8, A4, A8, A3 and A7 are only available at specified terminal modules.
Terminal assignment for 2AI U HS (6ES7134-4FB51-0AB0)
Terminal Assignment Terminal Assignment Notes
1 M
0+ 5 M
1+
2 M
0- 6 M
1-
3 M
ana 7 M
ana
4 n.c. 8 n.c.
A4 AUX1 A8 AUX1
A3 AUX1 A7 AUX1
•Mn+: Input signal "+", Channel n
•Mn-: Input signal "-", Channel n
•Mana: Ground of the module
•n.c.: Not connected (max. DC 30 V can be connected)
•AUX1: Protective-conductor terminal or potential bus (freely usable
up to 230 VAC)
Properties
1.1 2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
8 Manual, 04/2007, A5E01076015-01
Usable terminal modules
Usable terminal modules for 2AI U HS (6ES7134-4FB51-0AB0)
TM-E15C26-A1
(6ES7193-4CA50-
0AA0)
TM-E15C24-A1
(6ES7193-4CA30-
0AA0)
TM-E15C24-01
(6ES7193-4CB30-
0AA0)
TM-E15C23-01
(6ES7193-4CB10-
0AA0)
Spring terminal
TM-E15S26-A1
(6ES7193-4CA40-
0AA0)
TM-E15S24-A1
(6ES7193-4CA20-
0AA0)
TM-E15S24-01
(6ES7193-4CB20-
0AA0)
TM-E15S23-01
(6ES7193-4CB00-
0AA0)
Screw-type terminal
TM-E15N26-A1
(6ES7193-4CA80-
0AA0)
TM-E15N24-A1
(6ES7193-4CA70-
0AA0)
TM-E15N24-01
(6ES7193-4CB70-
0AA0)
TM-E15N23-01
(6ES7193-4CB60-
0AA0)
Fast Connect
$
$8;
$
$
$
$8;
$$
99
0
0
0
3($8;
0
&RQQHFWLRQH[DPSOHV
Block diagram
3
3
0
/
$'8
0
$1$
08;
%DFNSODQHEXV
(76
EDFNSODQHEXV
LQWHUIDFH
9
Figure 1-1 Block diagram of the 2AI U HS
Properties
1.1 2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
Manual, 04/2007, A5E01076015-01 9
2AI U HS technical specifications (6ES7134-4FB51-0AB0)
Dimensions and weight
Width (mm) 15
Weight Approx. 40 g
Module-specific data
Supports isochronous operation Yes
Number of inputs 2
Cable length
•Shielded Max. 200 m
Parameter length 12 bytes
(4 bytes when used as 6ES7134 4FB50-0AB0)
Address space 4 bytes
Voltages, currents, potentials
Rated load voltage L+ (from the power module) 24 VDC
•Reverse polarity protection Yes
Galvanic isolation
•Between the channels and backplane bus Yes
•Between the channels and load voltage L+ Yes
•Between the channels No
Permissible potential difference
•Between the inputs and MANA (UCM) 100 VACSS
•Between MANA and the central grounding point
(UISO) 75 VDC / 60 VAC
Insulation tested 500 VDC
Current consumption
•Power supply and load voltage L+ (no load) Max. 35 mA
Power dissipation of the module Typically 0.8 W
Status, interrupts, diagnostics
Interrupts
•Hardware interrupt Can be assigned parameters1
Diagnostics function
•Group error display Red "SF" LED
•Diagnostic information can be displayed Possible2
Analog value generation
Measuring principle Instantaneous value encoding
Cycle time/resolution:
•Conversion time in ms (per channel) 0,1
•Cycle time in ms (per module) 1
•Resolution (including overrange) ± 10 V/13 bits + sign
± 5 V/13 bits + sign
± 2.5 V/13 bits + sign
1 V to 5 V/13 bits
Properties
1.1 2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
2AI U HS analog electronic module (6ES7134-4FB51-0AB0)
10 Manual, 04/2007, A5E01076015-01
Suppression of interference, limits of error
•Common mode interference (Ucm) < 100 VSS) > 70 dB
Crosstalk between the inputs > 50 dB
Operational limit
(in the entire temperature range, with reference to
the input range)
± 0,3 %
Basic error limit (operational limit at 25°C with
reference to input range)
± 0,2 %
Temperature error (with reference to the input
range)
±0,01 %/K
Linearity error (with reference to the input range) ± 0,01 %
Repeatability
(in steady state at 25°C with reference to input
range)
± 0,05 %
Data for selecting a sensor
Input ranges (rated value)/input resistance
•Voltage ± 10 V/min. 100 kΩ
± 5 V/min. 100 kΩ
± 2.5 V/min. 100 kΩ
1 V - 5 V/min. 100 kΩ
Maximum input voltage for voltage input
(destruction limit)
50 V continuous, 100 V at max. duration of 1 ms
(sampling ratio 1:20)
Connection of the sensors
•For measuring voltage
Supported
Smoothing of the measured values Yes, can be assigned parameters in 4 steps by
means of digital filtering
Step
None
Weak
Medium
Strong
Time constant
1 x cycle time
64 x cycle time
128 x cycle time
512 x cycle time
1 DPV1 only
2 Parameter assignment error
Violation of lower limit value
Violation of upper limit value
Open circuit (only with 1 V to 5 V)
Process interrupt lost
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Siemens Unità di controllo
Siemens
Siemens SR-35 Manuale utente
Siemens
Siemens Simatic S7-1500 Manuale utente
Siemens
Siemens SINUMERIK 828D Turning Manuale utente
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens SIRIUS Manuale utente
Siemens
Siemens SIPROTEC4 7SJ61 Manuale utente
Siemens
Siemens CU230P-2 HVAC Manuale utente
Siemens
Siemens XC1003-A Manuale di istruzioni
Siemens
Siemens S-60 Manuale utente
Siemens
Siemens SINAMICS S120 Documento tecnico
Siemens
Siemens 6SE7022-0ES87-2DC0 Manuale di istruzioni
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens AZL2 Series Manuale utente
Siemens
Siemens SIMATIC RF170C Manuale utente
Siemens
Siemens QAW910 Manuale utente
Siemens
Siemens SINUMERIK 828D Turning Manuale elenco delle parti
Siemens
Siemens SIRIUS 3RA2712 Documento tecnico
Siemens
Siemens TL-30U Manuale utente
Siemens
Siemens Simatic S7-300 Manuale utente
Siemens
Siemens SIMATIC S5 1P 243 Documento tecnico
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
