Siemens 7SC80 Manuale utente

C53000-L2040-C353-3

SIPROTEC Compact

Feeder Protection

and Recloser Con-

troller 7SC80

Communication Module

DNP3 TCP

Bus Mapping/Point Lists

Preface

Contents

DNP3 TCP Device Profile 1

Point Lists 2

Flexible Mapping 3

Index

Disclaimer of Liability

This document has been subjected to rigorous technical review

before being published. It is revised at regular intervals, and any

modifications and amendments are included in the subsequent

issues. The content of this document has been compiled for

information purposes only. Although Siemens AG has made best

effortstokeepthedocumentaspreciseandup-to-dateaspossible,

Siemens AG shall not assume any liability for defects and damage

which result through use of the information contained herein.

This content does not form part of a contract or of business

relations; nor does it change these. All obligations of Siemens AG

are stated in the relevant contractual agreements.

Siemens AG reserves the right to revise this document from time to

time.

Document Release: C53000-L2040-C353-3.01

Edition: 09.2018

Product version: V1.05

The disclosure, duplication, distribution and editing of this

document, or utilization and communication of the content are not

permitted, unless authorized in writing. All rights, including rights

created by patent grant or registration of a utility model or a design,

are reserved.

Registered Trademarks

SIMATICTM, SIMATIC NETTM, SIPROTECTM, DIGSITM,

SICAMTM,SIMEASTM, SINAUTTM, OSCOPTM, and DAKONTM are

registered trademarks of SIEMENS AG. An unauthorized use is

illegal.

All other designations in this document can be trademarks whose

use by third parties for their own purposes can infringe the rights of

the owner.

NOTE

For your own safety, please observe the warnings and safety instructions contained in this document.

3SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Preface

Purpose of this manual

This manual describes the bus mapping of SIPROTEC 4 Communication Module with DNP3 TCP.

Target group

Protection engineers, commissioning engineers, persons who are involved in setting, testing and service of

protection, automation, and control devices, as well as operation personnel in electrical plants and power sta-

tions.

Scope of validity of this manual

This manual is valid for SIPROTEC 4 Communication Module with DNP3 TCP.

Further support

Should further information be desired or should particular problems arise which are not covered sufficiently for

the purchaser's purpose, the matter should be referred to the local Siemens representative.

Hotline

Our Customer Support Center provides around-the-clock support.

Phone: +49 (1805) 24-8437

Fax: +49 (1805) 24-2471

Internet: http://www.siprotec.com

e-mail: [email protected]

Training courses

If you are interested in our current training program, please contact our training center:

Siemens AG

Siemens Power Academy TD

Humboldtstr. 59

D-90459 Nuremberg

Germany

Phone: +49 (911) 433-7415

Fax: +49 (911) 433-5482

e-mail: poweracademy[email protected]

Internet: http://www.siemens.com/poweracademy

Preface

4 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Notes On Safety

Thismanual doesnotconstituteacomplete catalogof allsafetymeasures required for operating the equipment

(module, device) inquestion, because special operating conditionsmay require additionalmeasures.However,

it does contain notes that must be adhered to for your own personal safety and to avoid damage to property.

These notes are highlighted with a warning triangle and different keywords indicating different degrees of dan-

ger.

DANGER

DANGER means that death or severe injury will occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent death or severe injury.

WARNING

WARNING means that death or severe injury can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent death or severe injury.

CAUTION

CAUTION means that minor or moderate injury can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent minor injury.

NOTICE

NOTICE means that damage to property can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent damage to property.

NOTE

It is important information about the product, the handling of the product, or the part of the documentation in

question to which special attention must be paid.

Preface

5SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Qualified Personnel

Commissioning and operation of the equipment (module, device) described in this manual must be performed

by qualified personnel only. As used in the safety notes contained in this manual, qualified personnel are those

persons who are authorized to commission, release, ground and tag devices, systems, and electrical circuits

in accordance with safety standards.

Use as Prescribed

The equipment (device, module) must not be used for any other purposes than those described in the

Catalog and the Technical Description. If it is used together with third-party devices and components, these

must be recommended or approved by Siemens.

Correct and safe operation of the product requires adequate transportation, storage, installation, and

mounting as well as appropriate use and maintenance.

During the operation of electrical equipment, it is unavoidable that certain parts of this equipment will carry dan-

gerous voltages. Severe injury or damage to property can occur if the appropriate measures are not taken:

• Before making any connections at all, ground the equipment at the PE terminal.

• Hazardous voltages can be present on all switching components connected to the power supply.

• Even after the supply voltage has been disconnected, hazardous voltages can still be present in the equip-

ment (capacitor storage).

• Equipment with current transformer circuits must not be operated while open.

• The limit values indicated in the manual or the operating instructions must not be exceeded; this also

refers to testing and commissioning

Preface

6 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

7SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1 DNP3 TCP Device Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 Data Objects Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.2 DNP3 TCP Device Profile Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 Point Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.1 Binary Input Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.2 Control Relay Output Blocks/Binary Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.3 Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.4 Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.1 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Contents

8 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

9SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

1 DNP3 TCP Device Profile

1.1 Data Objects Implementation 10

1.2 DNP3 TCP Device Profile Documents 13

DNP3 TCP Device Profile

1.1 Data Objects Implementation

10 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

1.1 Data Objects Implementation

The following table identifies which object variations, function codes and qualifiers the DNP3 TCP implemen-

tation of the Feeder Protection and Recloser Controller 7SC80 will support in both request messages and in

response messages.

For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with

qualifiers 00 or 01.

Requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28.

For change-event objects, qualifiers 17 or 28 are always responded.

Note

Further information see in the SIPROTEC 4 document Communication Module DNP3 TCP - Communication

Profile, order number C53000-L2040-C354 or in Internet http://siemens.siprotec.de/download_neu/

index_e.htm.

Table 1-1 DNP3 TCP implementation table

Objects Request Response

Object

No. Var.

No. Description Function Codes

(dec) Qualifier Codes

(hex) Function Codes

(dec) Qualifier Codes

(hex)

1 0 Binary Input -

Any Variations 1 (read) 00, 01 (start-stop)

06 (no range)

07, 08 (limited qfy)

17, 28 (index)

1 2 Binary Input

with Status 1 (read) 00, 01 (start-stop)

06 (no range)

07, 08 (limited qfy)

17, 28 (index)

129 (response) 00, 01 (start-stop)

17, 28 (index)

2 0 Binary Input Change -

Any Variations 1 (read) 06 (no range, or all)

07, 08 (limited qfy)

2 2 Binary Input Change

with Time 1 (read) 06 (no range, or all)

07, 08 (limited qfy) 129 (response)

130 (unsol. resp) 17, 28 (index)

10 0 Binary Output -

Any Variations 1 (read) 00, 01 (start-stop)

06 (no range, or all)

07, 08 (limited qfy)

17, 28 (index)

10 2 Binary Output

with Status 1 (read) 00, 01 (start-stop)

06 (no range, or all)

07, 08 (limited qfy)

17, 28 (index)

129 (response) 00, 01 (start-stop)

17, 28 (index)

12 1 Control Relay Output

Block 3 (select)

4 (operate)

5 (direct op.)

6 (dir. op. noack)

17, 28 (index) 129 (response) echo of response

Altri manuali per 7SC80

Indice

Altri manuali Siemens Unità di controllo

Siemens

Siemens SIMATIC Manuale utente

Siemens

Siemens SINUMERIK 808D Manuale utente

Siemens

Siemens CM 1243-5 Manuale utente

Siemens

Siemens MICROMASTER 420 Manuale utente

Siemens

Siemens SINUMERIK 840D sl Manuale elenco delle parti

Siemens

Siemens SINAMICS Startdrive Manuale utente

Siemens

Siemens SPCW110 Manuale utente

Siemens

Siemens SINUMERIK 840D sl Manuale utente

Siemens

Siemens SINUMERIK 828D Turning Manuale utente

Siemens

Siemens SINUMERIK 840Di Manuale

Siemens

Siemens 3SB5 Manuale di istruzioni

Siemens

Siemens SIMATIC 505 PPX:505-6108A Manuale utente

Siemens

Siemens WF 705 Istruzioni per l'uso e l'installazione

Siemens

Siemens SINUMERIK 828D Turning Manuale del proprietario

Siemens

Siemens Simatic S7-1500/ET 200MP Documento tecnico

Siemens

Siemens FCM-6S Manuale utente

Siemens

Siemens VAG61 Series Manuale utente

Siemens

Siemens IM 328-N Istruzioni per l'uso e l'installazione

Siemens

Siemens SINAMICS G130 Manuale utente

Siemens

Siemens SINUMERIK 840D sl Manuale utente

Siemens

Siemens SIRIUS ACT 3SU1400-2EM10-6AA0 Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens SIMATIC S5 Manuale utente

Siemens

Siemens SINUMERIK 828D Turning Manuale elenco delle parti

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente