Siemens FS-TRI-M Manuale utente

SiemensBuilding Technologies, Inc.

FlorhamPark, New Jersey 07932

RED BLK ORG ORG GRN

EARTH

GND

TOCONTROL PANEL

ORPREVIOUS ADDRESSABLE DEVICE

MODEL: FS-TRI-M

REFER TO INSTL. INSTR.

P/N 315-699487

DEVICE ADDR.__________

ALLTERMINALS ARE POWERLIMITED

NOTE:

DO NOT USE

REAR CONDUIT ENTRY

SINGLE GANG

SWITCHBOX

(USER SUPPLIED)

SINGLE GANG

SWITCHPLATE (BLANK)

(USER SUPPLIED)

FS-TRI-M

UNDERWRITERS

LABORATORIES

The SIEMENS FS-TRI-M Contact Monitoring Module,

as shown in Figure 1, interfaces normally open contact

devices to an ddressable Device Circuit of a fire

alarm control unit.

The FS-TRI-M supports Style B (Class B) Initiating

Device Circuit wiring. Each module uses one address

on the ddressable Device Circuit. It does not require

any mechanical address programming. Use the FS-FPI

Programmer/Tester to program and test the module.

PROGRAMMING INSTRUCTIONS

CAUTION:

1. To prevent damage to the FS-FPI, do not

connect module to the FS-FPI until the

Addre able Device Circuit wiring i

di connected.

2. Only one device mu t be connected to the

FS-FPI at a time.

1. Connect the red and black wires of the FS-TRI-M

to the SIEMENS FS-FPI Programmer/Tester. Use

the cable provided with the Programmer/Tester

and the 2 alligator clips provided.

2. Set the address for the module by following the

instructions in the FS-FPI Programmer/Tester

Manual (P/N 315-699480).

3. Record the device address on the label located

on the module. The module can now be installed

and wired to the system.

MOUNTING

The FS-TRI-M mu t be in talled in a

UL Li ted electrical box.

Refer to Figure 2.

1. Connect the appropriate wires using wire nuts.

Tuck the FS-TRI-M module inside the electrical

box and dress the wiring as required.

2. Fasten the cover plate (user supplied) to the box.

Figure 2

FS-TRI-M Mounting

P/N 315-699487-1

Siemens Building Technologies, Inc.

8 ernwood Road

lorham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Installation Instructions

Models FS-TRI-M

Contact Monitoring Module

Fire Safety

Figure 1

FS-TRI-M Module

Figure 3

FS-TRI-M Wiring

NOTES:

1. ll circuits are power limited.

2. In supervisory:

FS-TRI-M draws 1.5m

3. Initiating Device Circuit ratings:

Style B, Class B

See NFP 72 standard for the number of normally open contact devices allowed.

Voltage (max.): 5 VDC (during polling)

Supervisory current (max.): 0.5m (during polling)

larm current (max.): 0.8m (during polling)

IDC cable requirements:

Wire size: 18 to 14 WG

Wire resistance (max.): 2 ohms

Cable length (max.): 200 feet

Cable Type: Data grade, twisted pair

4. If Earth Ground is available, the green wire should be connected to earth ground.

5. If Earth Ground is NOT available, the IDC wiring should be limited to the same room.

RED

BLACK

GREEN

ORANGE

FS-TRI-M

-TO NEXT

ADDRESSABLE DEVICE

FROM ADDRESSABLE DEVICE

CIRCUIT OF A COMPATIBLE

CONTROL UNIT OR PREVIOUS

ADDRESSABLE DEVICE

GROUND

SEE NOTES 4 AND 5

END OF LINE RESISTOR

P/N 140-820185

3.6K, 1/4W, 5%

CONTACT DEVICE

INITIATING DEVICE CIRCUIT

SUPERVISED, SEE NOTE 3

ADDRESSABLE DEVICE CIRCUIT

24VDC NOMINAL, SUPERVISED

WIRING

Remove all y tem power before in tallation, fir t battery and then AC.

(To power up, connect AC first then battery.)

Refer to the wiring diagram and wire the module accordingly.

P/N 315-699487-1

Altri manuali Siemens Unità di controllo

Siemens

Siemens SENTRON PAC PROFIBUS DP Manuale utente

Siemens

Siemens SIMATIC 8DO 24 V DC/0.5 A HF Manuale utente

Siemens

Siemens PXC-16 Compact Manuale del prodotto

Siemens

Siemens CU240S DP-F Manuale utente

Siemens

Siemens Milltronics BW500 Manuale utente

Siemens

Siemens SIRIUS 3RA2130-4 A3 Series Manuale utente

Siemens

Siemens SINUMERIK 828D Turning Manuale utente

Siemens

Siemens FDCL221-M Manuale utente

Siemens

Siemens Simatic S7-1500 Manuale elenco delle parti

Siemens

Siemens REMBOX2-MP Manuale utente

Siemens

Siemens SINUMERIK 828D Turning Manuale utente

Siemens

Siemens SIMATIC ET 200SP HA Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens OMM-2 Manuale utente

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A Manuale utente

Siemens

Siemens SINAMICS G120P CU230P-2 Guida per l'amministratore

Siemens

Siemens VN2001-A1 Manuale utente

Siemens

Siemens ACVATIX PS53 Manuale utente

Siemens

Siemens RS-485 Manuale utente

Siemens

Siemens 550-818B Manuale utente

Siemens

Siemens SIPROTEC 7VE61 Manuale utente

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 Manuale utente

Siemens

Siemens SIRIUS 3TK2834 Manuale utente

Siemens

Siemens XDACT-ASSY Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente