Siemens MEM-1 Manuale utente

P/N 315-093943-5

Installation Instructions

Model MEM-1

MXL Memory Expansion Module

1. Install the new IC107

A new IC107 (20-pin IC) for the MMB-1 is re-

quired to support the MEM-1. This new IC107

replaces the existing IC107 which is in a socket

just above and to the left of the expansion con-

nector P7 (See Figure 1).

a. Remove the old IC107 from the socket

and replace it with the new IC107 in the

MEM-1 kit.

b. Be sure that pin 1 of the new IC107 is

pointing down (toward P7).

2. Install the MEM-1

The MEM-1 installs into P7 on the MMB-1. P7 is

a 40-position DIP socket labeled Expansion

Connector which is located at the bottom center

of the MMB-1. The MEM-1 installs into this socket

and spans IC101 which is the large square

device to the right of P7. The MEM-1 has an

adhesive backed nylon standoff that supports the

right side of the module. This standoff must be

installed.

a. Remove the paper on the standoff to

expose the adhesive.

b. Insert the 40 pin header (P1) into P7 on

the MMB-1 being careful to align all of the

pins. You may have to adjust the standoff

so that it clears IC101.

c. Once the header is fully inserted, press

down on the right side of the module to

adhere the standoff to the MMB-1.

OPERATION

The Model MEM-1 Memory Expansion module

kit provides the MXL System with the additional

memory required to support MMB firmware

revisions 7.0 and higher. If your MXL System is

being upgraded to an MMB firmware revision

of 7.0 or higher and the MMB-1 does not have

a factory installed MEM-1, then you must install

the MEM-1.

INSTALLATION

CAUTION:

Remove all system power before

installation, first battery and then AC.

NOTE: If the MKB-1 in your MXL System

straddles the MMB-1 board, remove

the MKB-1 before proceeding.

NOTE: If your MXL System has an IEC-1

module, remove it before installing the

MEM-1.

The installation kit for the MEM-1 includes the

following items:

1. New IC107 (replaces IC107 on MMB-1)

2. MEM-1

3. Nylon standoff

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

3. Set the Jumper on the MEM-1

The MEM-1 has a configuration jumper P2 (See

Figure 2) that must be set to work with the

MSU-1K kit that contains the new firmware. Refer

to the MSU-1K Installation Instructions, P/N 315-

092542, for the proper setting of the jumper.

4. Install the EPROM on the MEM-1

Included in the MSU-1K kit is an EPROM labeled

U2. This EPROM goes into the U2 socket on the

MEM-1. Refer to the MSU-1K Installation Instruc-

tions, P/N 315-092542, for the procedure to install

the EPROM.

5. Re-install the IEC-1

If the IEC-1 was removed before installing the

MEM-1, re-install it now.

6. Re-install the MKB-1

If the MKB-1 was removed before installing the

MEM-1, re-install it now.

Figure 2

The MEM-1

ELECTRICAL RATINGS

5VDC, 100mA

Figure 1

The MMB-1

P/N 315-093943-5

CB1

NAC1

POWER

AC INPUT

BATTERY

20A

BATTERY F5 CZM-1 POWER

CB2

NAC2

CZM-1

POWER

TB3

POWER TO MOM-4

2 AMP MAX.

ANALOG

LOOP 2

NAC 2

NAC 1

TO ANN-1, P1

(ON BACK OF MKB)

POLLING

TB2

ANALOG

LOOP 1

NETWORK SPV

TAMPER

SWITCH

TRBL

IC 101

TB1

PROGRAMMER

P10

D2300CP PRINTER

MOM-4 1

P6 111111

EXPANSION

ALR

MMB-1

Altri manuali Siemens Unità di controllo

Siemens

Siemens Simatic S7-1500 Manuale utente

Siemens

Siemens RUGGEDCOM RS900F Manuale utente

Siemens

Siemens Simatic S7-1500 Manuale utente

Siemens

Siemens SIMATIC ET 200S Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens WFZ43 Manuale utente

Siemens

Siemens SINUMERIK 808D Manuale utente

Siemens

Siemens SIRIUS 3RW5 series Manuale utente

Siemens

Siemens SIRIUS 3SF5811 A Series Manuale utente

Siemens

Siemens SINUMERIK 840D Guida all'installazione

Siemens

Siemens CP 443-5 Extended Manuale utente

Siemens

Siemens SIMATIC NET 6GK1110-1AA00 Manuale utente

Siemens

Siemens SIROTEC Manuale tecnico

Siemens

Siemens 7KT1 908 Manuale utente

Siemens

Siemens LOK16 Series Manuale utente

Siemens

Siemens SIWAREX MS Guida all'applicazione

Siemens

Siemens SIRIUS ACT 3SU1401-2EE20-6AA0 Manuale utente

Siemens

Siemens SINAMICS G130 Manuale utente

Siemens

Siemens FT2001-A1 Manuale utente

Siemens

Siemens HiPath optiPoint 410 Manuale di istruzioni

Siemens

Siemens Simatic ET200pro Manuale utente

Siemens

Siemens RMB795 Manuale utente

Siemens

Siemens VVP47 Series Manuale utente

Siemens

Siemens VVG44.15-0.4S Manuale del proprietario

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente