Siemens SED2-LONI/F Manuale utente

Installation Instructions

Document No. 129-387

October 2, 2009

SED2 VFD LON Interface Option

Item Number 129-387, Rev. BA Page 1 of 3

Product Description

The LONMARK® certified SED2 VFD LON Interface

Option (LON Interface) provides direct digital control of

SED2 Variable Frequency Drives (VFDs). The LON

Interface resides on a LONWORKS® network with

LONMARK products from multiple vendors.

Product Numbers

SED2-LONI/F, includes SED2 VFD LON Interface

Option, and CD-ROM with files and operating

instructions.

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not perform a

procedure as specified.

CAUTION:

Equipment damage, or loss of

data may occur if you do not

perform a procedure as specified.

Installation

SED2 VFD Frame Sizes A, B, and C

WARNING:

Make sure that the SED2 VFD is

de-energized (off) before you install or

remove the LON Interface Option.

1. Remove the SED2 VFD operator panel.

2. Install the LON Interface on the SED2 VFD I/O

module (Figure 1) by inserting two bottom guides

into appropriate slots at the sides of the I/O

module and pushing the upper section inward

until the locking mechanism latches.

3. Route the network cable (without connector) to

the LON Interface.

4. Terminate the end of network cable with a single,

two-pin, female LONWorks FTT-10A connector.

5. Attach the network cable FTT-10A connector to

connector at bottom of LON Interface (Figure 2).

6. Reinstall SED2 VFD operator panel on LON

Interface.

Figure 1. Installing LON Interface Option on SED2 VFD

Frame Sizes A, B, and C.

Figure 2. Network Connection on Bottom of

LON Interface Option.

SED2

VFD

INTERFACE

OPTION

Document No. 129-387

Installation Instructions

October 2, 2009

Page 2 of 3 Siemens Industry, Inc.

SED2 VFD Frame Sizes D, E, and F

WARNING:

Make sure that the SED2 VFD is

de-energized (off) before you install or

remove the LON Interface Option.

For frame sizes D, E, and F, the LON Interface mounts

inside the VFD housing.

1. Remove the SED2 VFD operator panel, side

cover, and bottom cover (Figures 3).

2. Disconnect operator panel extension module

(with ribbon cable) from control module by

pushing lever above extension module upwards

and simultaneously pulling extension module from

the upper sides and rocking it downward.

NOTE: Do not disconnect the ribbon cable.

3. Install the LON Interface on the control module

(Figure 4) by inserting two bottom guides into

appropriate slots at the sides of the control

module and pushing the upper section inward

until the locking mechanism latches.

4. Install the operator panel extension module on

LON Interface (Figure 4) by inserting two bottom

guides into appropriate slots at the sides of the

LON Interface and pushing the upper section

inward until the locking mechanism latches.

5. Route the network cable (without connector)

through a suitable cable opening to the LON

Interface (Figure 4).

6. Terminate the end of network cable with a single,

two-pin, female LONWorks FTT-10A connector.

7. Attach the network cable FTT-10A connector to

connector at bottom of LON Interface (Figure 2

and 4).

8. Reinstall the bottom cover, side cover, and the

SED2 VFD operator panel.

Figure 3. Removing the Operator Panel and Side Cover

of SED2 VFD Frame Sizes D, E, F.

Figure 4. Installing LON Interface Option on SED2 VFD Frame Sizes D, E, and F.

Document No. 129-387

Installation Instructions

October 2, 2009

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and

models as design improvements are introduced. Echelon, LonMark, LonWorks, LonTalk are registered trademarks of Echelon Corporation.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089

+ 1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com

Document No. 129-387

Printed in the USA

Page 3 of 3

Wiring

WARNING:

A VFD can be switched on unintentionally if

the serial bus installation is not operated

correctly. Only personnel who are qualified

and trained in installing systems of this type

should start the bus.

DIP Switch

Leave DIP switches OFF for proper operation of the

LON Interface.

WIRING

Wiring must conform to local codes and ordinances.

WIRE ROUTING

Maintain a minimum of 5 ft (1.5 m) between VFDs and

network or sensor wiring.

If it is necessary for network and sensor wring to cross

VFD wiring, it should cross at 90-degree angles.

POWER

The LON Interface receives power through its SED2

VFD connection. If VFD power is switched off, the

LON Interface will not communicate on the network.

LONTalk® NETWORK

The LONTalk network connection is on the bottom

edge of the LON Interface (Figure 2). Figure 5 shows

the wiring schematic for this connection. See

www.echelon.com for more details on the network

cable and the FTT-10A connector.

The installation is now complete.

NOTE: This connection supports twisted pair,

unshielded, polarity-insensitive, peer-to-peer

communications at 78 Kbps.

Figure 5. LON Interface Option Wiring Schematic.

Altri manuali Siemens Unità di controllo

Siemens

Siemens SIPROTEC Manuale utente

Siemens

Siemens HZM Manuale utente

Siemens

Siemens FM 458-1 DP Manuale utente

Siemens

Siemens SINUMERIK 808D Manuale utente

Siemens

Siemens MVS661 N Series Manuale utente

Siemens

Siemens simovert masterdrives Manuale utente

Siemens

Siemens FN2006-U1 Guida

Siemens

Siemens SINUMERIK 840D Simodrive 611 digital Guida utente

Siemens

Siemens SINUMERIK 808D Guida all'installazione

Siemens

Siemens 4AI RTD Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens SINUMERIK 840C Manuale

Siemens

Siemens 7XT71 Series Manuale utente

Siemens

Siemens SITRANS F Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens SINUMERIK 840Di Manuale

Siemens

Siemens SINUMERIK 840C Manuale utente

Siemens

Siemens 2AO U HF Manuale utente

Siemens

Siemens 3VM9.88-0LB10 Manuale utente

Siemens

Siemens SIMATIC ET 200eco PN Manuale utente

Siemens

Siemens SIMATIC FM 351 Manuale utente

Siemens

Siemens MLC Manuale utente

Siemens

Siemens SIMATIC ET 200AL Manuale utente

Siemens

Siemens SICAM FCG Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente