Siemens SIMATIC NET CP 142-2 Manuale utente

SIMATIC NET

CP 142-2

Manual

1 Introduction

2 Technical Description and Installation Instructions

3 Standard Operation

4 Extended Operation

5 Replacing a Defective Slave / Automatic Address Programming

6 Error Indicators / Dealing with Errors

7 PROFIBUS DP Configuration When Using the

BM141/BM142

A AS-Interface Protocol Implementation

Conformance Statement (PICS)

B References

C Abbreviations

C79000-G8976-C111 Release 02

SIMATIC NET is a trademark of Siemens

Siemens Aktiengesellschaft

Wir haben den Inhalt der Druckschrift auf

Übereinstimmung mit der beschriebenen Hard- und

Software geprüft. Dennoch können Abweichungen

nicht ausgeschlossen werden, so daß wir für die

vollständige Übereinstimmung keine Gewähr

übernehmen. The Angaben in der Druckschrift

werden jedoch regelmäßig überprüft. Notwendige

Korrekturen sind in den nachfolgenden Auflagen

enthalten. Für Verbesserungsvorschläge sind wir

dankbar.

Technische Änderungen vorbehalten.

Weitergabe sowie Vervielfältigung dieser Unterlage,

Verwertung und Mitteilung ihres Inhalts nicht gestattet,

soweit nicht ausdrücklich zugestanden.

Zuwiderhandlungen verpflichten zu Schadenersatz.

der Patenterteilung oder GM-Eintragung.

C79000-G8900-C111

We have checked the contents of this manual for

agreement with the hardware described. Since

deviations cannot be precluded entirely, we cannot

guarantee full agreement. However, the data in this

manual are reviewed regularly and any necessary

corrections included in subsequent editions.

Suggestions for improvement are welcome.

Technical data subject to change.

The reproduction, transmission or use of this

document or its contents is not permitted without

express written authority. Offenders will be liable for

damages. All rights, including rights created by patent

grant or registration of a utility or design, are reserved.

C79000-G8976-C111

Nous avons vérifié la conformité du contenu du

présent manuel avec le matériel et le logiciel qui y

sont décrits. Or, des divergences n'étant pas exclues,

nous ne pouvons pas nous porter garants pour la

conformité intégrale. Si l'usage du manuel devait

révéler des erreurs, nous en tiendrons compte et

apporterons les corrections nécessaires dès la

prochaine édition. Veuillez nous faire part de vos

suggestions.

Nous nous réservons le droit de modifier les

caractéristiques techniques.

Toute communication ou reproduction de ce support

d'informations, toute exploitation ou communication

de son contenu sont interdites, sauf autorisation

expresse. Tout manquement à cette règle est illicite et

expose son auteur au versement de dommages et

intérêts. Tous nos droits sont réservés, notamment

pour le cas de la délivrance d'un brevet ou celui de

l'enregistrement d'un modèle d'utilité.

C79000-G8972-C111

Siemens Aktiengesellschaft Elektronikwerk Karlsruhe

Printed in the Federal Republic of Germany

SIMATIC NET

CP 142-2

Manual C79000-B8976-C111/02

We would point out that the contents of this product documentation shall not become a part of or modify any prior or existing

agreement, commitment or legal relationship. The Purchase Agreement contains the complete and exclusive obligations of

Siemens. Any statements contained in this documentation do not create new warranties or restrict the existing warranty.

We would further point out that, for reasons of clarity, these operating instructions cannot deal with every possible problem arising

from the use of this device. Should you require further information or if any special problems arise which are not sufficiently dealt

with in the operating instructions, please contact your local Siemens representative.

General This device is electrically operated. In operation, certain parts of this device carry a dangerously high voltage.

WARNING! Failure to heed warnings may result in serious physical injury and/or material damage.

Only appropriately qualified personnel may operate this equipment or work in its vicinity. Personnel must be

familiar with all warnings and maintenance measures in accordance with these operating instructions.

Correct and safe operation of this equipment requires proper transport, storage and assembly as well as

careful operator control and maintenance.

Personnel qualification requirements

Qualified personnel as referred to in the operating instructions or in the warning notes are defined as persons who are familiar with

the installation, assembly, startup and operation of this product and who possess the relevant qualifications for their work, e.g.:

− Training in or authorization for connecting up, grounding or labeling circuits and devices or systems in accordance with current

standards in safety technology;

− Training in or authorization for the maintenance and use of suitable safety equipment in accordance with current standards in

safety technology;

− First Aid qualification.

B8976111/02 Contents

I-1

Contents

1 Introduction 1-1

1.1 General 1-2

1.1.1 Overview of the Chapters 1-2

1.1.2 General Information for the Reader 1-3

1.1.3 Requirements for Understanding the Manual 1-4

1.1.4 Sample Programs 1-5

1.1.5 Further Support and Hotline 1-5

2 Technical Description and Installation Guidelines 2-1

2.1 Overview of the Module 2-2

2.1.1 Introduction 2-2

2.1.2 Technical Specifications of the Module 2-3

2.1.3 Installing and Connecting the CP 142-2 2-4

2.1.4 Indicators and Operator Controls on the CP 142-2 2-6

2.1.4.1 Meaning of the Indicators and Operator Controls: 2-6

2.1.4.2 Status Display of the CP 142-2 (all group LEDs off) 2-7

2.1.4.3 Slave Display of the CP 142-2 (at least on group LED lit) 2-8

2.1.4.4 Meaning of theSET/DISPLAY Button 2-9

2.1.4.5 Slots Permitted for the CP 142-2 in the ET 200X Distributed I/O Station 2-9

2.1.4.6 Configuring the AS-Interface with the SET/DISPLAY Button 2-9

2.1.4.7 Types of Operation with the CP 142-2 2-11

3 Standard Operation of the CP 142-2 3-1

3.1 Addressing the CP 142-2 3-1

3.1.1 Addressing using the BM141/BM142 3-1

3.1.2 Addressing when using the BM147 3-1

3.2 How the User Program Addresses the AS-i Slaves 3-2

3.2.1 Addressing AS-i User Data 3-2

3.2.2 Accessing the AS-i User Data (BM141, BM142) 3-4

3.2.3 Access to the AS-i User Data (BM147) 3-5

3.3 Diagnostics and Reaction to Interrupts on the CP 142-2 3-6

3.3.1 Diagnostics and Reaction to Interrupts with the BM141/BM142 3-6

3.3.1.1 Interrupt Events 3-6

3.3.1.2 Structure of PROFIBUS DP Slave Diagnostics 3-7

3.3.2 Diagnostics and Reaction to Interrupts with the BM147 3-10

3.3.2.1 Overview 3-10

3.3.2.2 Interrupt Events 3-10

3.3.2.3 Sequence of Diagnostic Interrupt Servicing 3-11

3.3.2.4 Response to Interrupts in Various CP States 3-11

3.3.2.5 Local Data of the Diagnostic Organization Block (OB82) 3-12

3.3.2.6 Reading the Diagnostic Data Record DS1 3-13

3.3.2.7 Programming Example 3-14

4 CP 142-2 Extended Operation with FC “ASI_3422” 4-1

4.1 Overview of the Functions 4-1

4.1.1 Calling the Function 4-1

4.2 Interface for AS-i commands 4-7

4.2.1 The Commands Supported by the CP 142-2 4-7

4.2.1.1 Set_Permanent_Parameter 4-8

4.2.1.2 Get_Permanent_Parameter 4-8

4.2.1.3 Write_Parameter 4-9

4.2.1.4 Read_Parameter 4-9

B8976111/02 Contents

I-2

4.2.1.5 Store_Actual_Parameters 4-10

4.2.1.6 Set_Permanent_Configuration 4-10

4.2.1.7 Get_Permanent_Configuration 4-11

4.2.1.8 Store_Actual_Parameters 4-11

4.2.1.9 Read_Actual_Configuration 4-12

4.2.1.10 Set_LPS 4-12

4.2.1.11 Set_Offline_Mode 4-13

4.2.1.12 Set_Auto_Address 4-14

4.2.1.13 Set_Operation_Mode 4-14

4.2.1.14 Change_Slave_Address 4-15

4.2.1.15 Read Slave Status 4-16

4.2.1.16 Read Lists and Flags (Get_LPS, Get_LAS, Get_LDS, Get_Flags) 4-17

4.2.1.17 Read Total Configuration 4-19

4.2.1.18 Configure Total System 4-21

4.2.1.19 Write Parameter List 4-24

4.2.1.20 Read Parameter Echo List 4-25

4.2.1.21 Read Version ID 4-26

4.2.1.22 Read and Reset Slave Status 4-27

4.2.1.23 Read Slave ID 4-28

4.2.1.24 Read Slave I/O 4-28

5 Replacing a Defective Slave / Automatic Address Programming 5-1

6 Error Indicators on the CP 142-2 / Dealing with Errors 6-1

7 Configuring PROFIBUS DP When Using the BM141/BM142 7-1

A AS-Interface Protocol Implementation Conformance Statement (PICS)

B References

C Abbreviations

B8976111/02 AS-i Master Module CP 142-2

1-1

1 Introduction

This manual describes the functions and the programming of the CP 142-2. To fully understand this

manual, you should be familiar with the manual ‘AS-Interface Introduction and Basic Information’.

We recommend the following procedure when...

...You want a general overview of the

AS-Interface.

´

Read the manual ‘AS-Interface

Introduction and Basic Information'.

This manual contains general

information about the AS-Interface,

generally referred to as AS-i in this

manual.

...You want to install and start up the CP

142-2.

´

Chapter 2 Section 2.1 ‘Overview of the

Module’ and Chapter 3 ‘Standard

Operation of the CP 142-2’ contain the

information you require.

...You want to know how to program the

CP 142-2.

´

Read Chapters 3 and 4.

...you want to create a PLC program for

standard applications.

´

Chapter 3 contains all the information

you require about standard operation.

...you require additional information about

extended operation.

´

You will find the required information in

Chapter 4.

B8976111/02 AS-i Master Module CP 142-2

1-2

1.1 General

1.1.1 Overview of the Chapters

Chapter 1 Introduction

This chapter explains how to make the best use of the manual.

Chapter 2 Technical Description and Installation Guidelinesn

Chapter 2 provides you with an overview of the modes, installation and startup and the indicators and

operator controls of the CP 142-2.

Chapter 3 Standard Operation of the CP 142-2

Chapter 3 describes how to operate the CP 142-2 in the ET 200X distributed I/O system in standard

operation.

Chapter 4 CP 142-2 Extended Operation with FC “ASI_3422”

Chapter 4 describes the extended operation of the CP 142-2, that requires the

FC “ASI_3422” in the control program. In this type of operation, the AS-i slaves can be assigned

parameters or the slave addresses can be modified by the S7 program.

This mode is only possible with the BM147.

Chapter 5 Replacing a Defective Slave / Automatic Address Programming

Chapter 5 explains how to replace a failed AS-i slave quickly and simply.

Chapter 6 Error Indicators on the CP 142-2 / Dealing with Errors

This chapter explains the possible error indications on the CP 142-2 and explains how to deal with

them.

Chapter 7 PROFIBUS DP Configuration When Using the BM141/BM142

Chapter 7 contains additional information about DP configuration of the BM141/BM142.

B8976111/02 AS-i Master Module CP 142-2

1-3

1.1.2 General Information for the Reader

General symbols in the text:



This symbol indicates an action for you to perform.



This symbol highlights special features and dangers.

B8976111/02 AS-i Master Module CP 142-2

1-4

1.1.3 Requirements for Understanding the Manual

To fully understand the manual, you should already be familiar with the following:

±

The manual ‘AS-Interface Introduction and Basic Information’.

±

The manual 'ET 200X Distributed I/O System’

Indice

Altri manuali Siemens Unità di controllo

Siemens

Siemens DMS8000 MP4 Series Istruzioni operative e di manutenzione

Siemens

Siemens SENTRON PAC RS485 Manuale utente

Siemens

Siemens SIMATIC S7-1200 Manuale elenco delle parti

Siemens

Siemens RCC-2/R Manuale utente

Siemens

Siemens PSO 4000 Manuale utente

Siemens

Siemens SITRANS F Manuale utente

Siemens

Siemens SINAMICS G120P Istruzioni per il montaggio

Siemens

Siemens MVS661 N Series Manuale utente

Siemens

Siemens RC-30U Manuale utente

Siemens

Siemens FM 458-1 DP Manuale utente

Siemens

Siemens SIRIUS ACT 3SU14 Manuale utente

Siemens

Siemens SINAMICS S120 Documento tecnico

Siemens

Siemens LGI16 Series Manuale utente

Siemens

Siemens EFB300 Manuale utente

Siemens

Siemens 3AK Manuale utente

Siemens

Siemens SIMATIC Panel PC 677 Manuale utente

Siemens

Siemens RMB795B Manuale dell'operatore

Siemens

Siemens TBM-2 Manuale utente

Siemens

Siemens OZW771 Manuale utente

Siemens

Siemens LAL Series Manuale utente

Siemens

Siemens MICROMASTER Vector 6SE32 Manuale utente

Siemens

Siemens PXC D Series Manuale utente

Siemens

Siemens SIPROTEC 6MU805 Manuale utente

Siemens

Siemens Cerberus Pyrotronics LP-30 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente