Siemens SZE-4X Manuale utente

P/N 315-096018-8

Installation Instructions

Model SZE-4X

Zone/Output Expander Module

Mounting the SZE-4X (Refer to Figure 1):

Install the Main Board of the SXL-EX or SXL-EX-INT

(See the SXL-EX Operation, Installation, and Mainte-

nance Manual, P/N 315-095997). Then install the

SZE-4X in the lower portion of the EN-SX enclosure

by following the steps listed below.

1. Screw the four standoffs onto the four studs

located in the lower portion of the SXL-EX

enclosure.

2. Place the SZE-4X over the four standoffs. Using

the four screws provided, fasten the SZE-4X

board to the standoffs.

Wiring

See Figure 2 for wiring connections from the SZE-4X

to the SXL-EX Main Board.

PROGRAMMING

Refer to the SXL-EX Operation, Installation, and

Maintenace Manual (P/N 315-095997) for program-

ming instructions related to IDC Zones, and Open

Collector and Relay Outputs.

OPERATION

The Model SZE-4X Zone/Output Expander module

from Siemens Industry, Inc., is used with the SXL-EX

to provide an additional four Class B (Style B) Initiating

Device Circuits, four Form C Relays, and four Open

Collector Output Circuits. All the devices on these

circuits are user programmable. Each inititiating

device circuit can drive up to 30 conventional type

detectors and an unlimited number of shorting type

devices. The SZE-4X can also be used with the

SXL-EX-INT.

ELECTRICAL CHARACTERISTICS

Supervisory: 41mA at 24 VDC

Alarm: 510mA at 24 VDC

Each IDC 120mA at 24 VDC

Each Relay 26mA at 24 VDC

INITIATING DEVICES

Each SZE-4X IDC Zone can connect to the initiating

devices indicated below:

1. Up to 30 smoke detectors may be used on an

SZE-4X zone. Compatible detectors are listed in

Table 1. Detectors of different models are not to

be mixed or matched on a system.

2. The PBA-1191 Beam Detector may be used as

shown in Figure 4. Only one PBA-1191 Beam

Detector may be used on an SZE-4X zone and

eight total on the system.

3. Any number of shorting type devices can be used

on a SZE-4X zone.

Refer to Figures 2, 3, and 4 for the wiring of the

detectors, shorting type devices, and the beam

detector devices.

INSTALLATION

Remove all system power before

installation, first battery and then AC.

(To power up, connect the AC first, then the battery.)

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

1ELBAT SROTCETEDELBITAPMOC

rotceteD

ytitnauQ rep pooLesaB

noitallatsnI snoitcurtsnI .oNtraP

H3/3-ID03S3-BD81-34918

0-513

H3A/3A-ID03S3-BD81-349180-513

H3B/3B-ID03I3-DA6-432390-513

531-P3-TD02S3-BD5-104480-513

11-TD0311-BD htiwS3-BD T

PDA-BD

3-924590-513 3-924590-513

1911-ABP11911-BBP3-424590-513

T3/3-EP03S3-DA PLI3-DA 7-578090-513 6-432390-513

1/11-EP0311-BD htiwS3-BD TPDA-BD

9-891490-513 9-891490-513

Figure 2

SZE-4X Wiring Diagram

Figure 3

Smoke Detector and Shorting Type Device

Wiring Diagram

NOTES:

1. The SXL-EX Control Panel meets NFPA 72

Local requirements.

2. All field wiring must be in accordance with

NFPA 70, Article 760.

3. Do not make any wiring connections

while the System is powered.

4. Form C relay contacts are shown de-

energized. They are not suitable for motor

or pilot duty.

5. Combined current output for NAC1, NAC2,

and auxiliary outputs is limited to 3.0 amps.

6. Equipment connected to these terminals

must be located within the same room.

7. In all cases the Siemens Industry, Inc.,

Model Number is the compatibility

identifier, including the Control Panel,

Module(s), and all Compatible Initiating

Devices.

Figure 4

PB-1191 Device Wiring Diagram

UL Listed EOL Device

3.9K, 1/2W, P/N 140-820386

(IDCs Supervised)

Class B (Style B)

UL Listed EOL Device

3.9K, 1/2W, P/N 140-820386

(IDCs Supervised)

Class B (Style B)

+ -

IDC 5

IDC 6

IDC 7

IDC 8

TB-3

TB-1

TB-2

To JP3

of SXL-EX

Main

Board

To JP3

of SXL-EX

Main

Board

JP1

FORM C

RELAY 1

FORM C

RELAY 1

(See

Note 6)

(See

Note 6)

(See Note 6)

(See

Note 6)

(See

Note 6)

(See

Note 6)

(See

Note 6)

(See

Note 6)

(See

Note 6)

FORM C

RELAY 2

FORM C

RELAY 2

FORM C

RELAY 3

FORM C

RELAY 3

FORM C

RELAY 4

FORM C

RELAY 4

OC 1 Programmable

OC 1Programmable

External

Load

External

Load

External

Load

External

Load

External

Load

External

Load

External

Load

External

Load

To External +24VDC

UL Listed, Regulated,

and Filtered power

supply.

To External +24VDC

UL Listed, Regulated,

and Filtered power

supply.

To SXL-EX

Main Board

-V TB-3

To SXL-EX

Main Board

-V TB-3

If External

Power Supply

is not available,

connect to

SXL-EX Main

Board

+24V TB-3.

(See Note 5)

If External

Power Supply

is not available,

connect to

SXL-EX Main

Board

+24V TB-3.

(See Note 5)

See Open Collector Electrical Rating Table

and Note 6

See Open Collector Electrical Rating Table

and Note 6

SZE-4X

OC 2 Programmable

OC 2Programmable

OC 3 Programmable

OC 3Programmable

OC 4 Programmable

OC 4Programmable

Programmable Programmable Programmable Programmable

See COMPATIBLE DETECTOR CHART and

INITIATING DEVICE CIRCUIT ELECTRICAL RATINGS

See COMPATIBLE DETECTOR CHART and

INITIATING DEVICE CIRCUIT ELECTRICAL RATINGS

Postive and Negative Ground Fault

Detected at <100K for Terminals on TB-3

Postive and Negative Ground Fault

Detected at <100K for Terminals on TB-3

PBA-1191 Device Wiring Diagram

TO IDC

ZONE

TO IDC

ZONE

- -

+ +

EOL RESISTOR

4.7K, 1/4W, P/N 140-820188

EOL RESISTOR

4.7K, 1/4W, P/N 140-820188

PBA-1191

A B CDEF

DO NOT

USE

DO NOT

USE

P/N 315-096018-8

INITIATING DEVICE CIRCUIT

Electrical Ratings

Voltage range: 18.2-26.8 VDC filtered

Supervisory current: 6mA

Alarm current: 120mA (max)

1. Maximum line impedance of 25 ohms

per IDC zone.

2. All IDC zones are supervised and power

limited per NFPA 70, Article 760.

3. Each IDC zone must use at least 18

AWG, 300V insulation, color-coded wire

for low voltage circuits where local

codes require conduit. Where local

codes permit, use limited energy

shielded cable rated at 300V.

4. Each IDC zone supports one initiating

device in alarm.

5. Maximum line capacitance is 10uF per

zone.

Figure 1

Mounting the SZE-4X Module

OPEN COLLECTOR

ELECTRICAL RATING TABLE

50mA (max) at 26.4 VDC (max)

Resistive Only

FORM C

RELAY ELECTRICAL RATINGS

2A at 30 VDC

200mA at 120 VAC Resistive Only

Altri manuali Siemens Unità di controllo

Siemens

Siemens SCALANCE W788C-2 Manuale utente

Siemens

Siemens 3VL92 Series Manuale utente

Siemens

Siemens SIRIUS ACT 3SU14 Manuale utente

Siemens

Siemens AP 641 Manuale di servizio

Siemens

Siemens MICROMASTER 420 Manuale utente

Siemens

Siemens SIMOCODE pro 3UF7400-1AA00-0 Manuale utente

Siemens

Siemens LVM Manuale utente

Siemens

Siemens 7SA513BB Series Istruzioni per l'uso e l'installazione

Siemens

Siemens DMS8000 MP4 Series Istruzioni operative e di manutenzione

Siemens

Siemens QAA73.210 Manuale utente

Siemens

Siemens SED2-MODBUS2 Manuale del proprietario

Siemens

Siemens SIRIUS 3RA2712-.A Series Manuale utente

Siemens

Siemens SINAMICS G120 Manuale utente

Siemens

Siemens SIMATIC Panel PC 677 Manuale utente

Siemens

Siemens SIMADYN D T400 Manuale elenco delle parti

Siemens

Siemens ZU-35 Manuale utente

Siemens

Siemens SIMATIC TI505 Manuale utente

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 Manuale utente

Siemens

Siemens CZM-4 Manuale utente

Siemens

Siemens SIRIUS 3SF5811 A Series Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens FS-TRI-M Manuale utente

Siemens

Siemens SIMATIC TI505 386/ATM Manuale utente

Siemens

Siemens MXG461B Series Manuale del proprietario

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente