Siemens TBM-2 Manuale utente

P/N 315-093782-9

INTRODUCTION

The Model TBM-2 Termination Block module

from Siemens Industry, Inc., is the central

connection point for audio functions in the

MXLV System (See Figure 1). The ACM-1

Audio Control module communicates with

other modules in the system through the

TBM-2. In addition, the TBM-2 has connections

for the recording of telephone and microphone

messages, and the control connections to

activate recording equipment. Refer to the

CSG-M Manual, P/N 315-090381, to select

the Voice Options for your system.

The TBM-2 has two single pole, double throw

(SPDT) dry contacts, AUX CTRL1 and AUX

CTRL2, that control recording equipment.

When the microphone or telephone is active,

the signal goes to the chosen auxiliary output

and the corresponding control output changes

state. The TBM-2 does not include connectors

or cables for connecting the auxiliary outputs

and auxiliary controls.

The TBM-2 has a connection for an external

signal source. Use the AUX IN input and a

VSM-1 function to connect an external signal

source to the MXLV System. See Figure 4 for

information on input signals.

The TBM-2 provides screw terminal blocks

and connectors that interface the internal

wiring and field wiring (See Table 1).

For additional information on the MXL/MXLV

System, refer to the MXL/MXLV Manual, P/N

315-092036.

INSTALLATION

Remove all system power before installation,

first battery and then AC. (To power up, connect

the AC first and then the battery.)

The TBM-2 mounts on the right side of the

backbox next to the MMB or PSR-1, approxi-

mately one-third of the way down from the top

(Refer to Figure 2).

NOTE: In a Remote Extender enclosure the

TBM-2 mounts below the PS-5N7. Refer

to the PS-5N7 Instructions, P/N 315-092729.

Installation Instructions

Model TBM-2

Termination Block Module

TABLE 1

TBM-2 CONNECTIONS

Connector Connects

TB2 Digital Message Unit audio signal

connection

TB5 Supervised riser signals to System

(Style Y or Z)

TB4 Supervised telephone riser signal

(Style Y)

P1 SPDT contact to start the recorder for

AUX OUT 1

P2, P3 Plug-in cable power connections for

ACM-1

P4 Plug-in cable power connection for

VSM-1/VLM-1/VFM-1

P5 Plug-in cable power connections for

TMM-1

P6 SPDT contact to start the recorder for

AUX OUT 2

J1 AUX IN RCA type jack

J2 AUX OUT 1 RCA type jack

J3 AUX OUT 2 RCA type jack

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

WIRING

Refer to Figures 3 and 4.

All wiring must comply with

national and local codes.

For the audio and telephone risers:

Maximum wire size: 14 AWG twisted

pair, shielded

Minimum wire size: 18 AWG twisted

pair, shielded

Maximum loop resistance: 20 ohms for both

wires

Connect the 24 VDC to TB3 using 14 AWG

single conductor wire. Terminal 1 is for +24

VDC; terminal 2 is for 24 VDC return.

Refer to the CSG-M configuration printout to

determine the wiring style (either Style Y or

Style Z) for terminal block TB5.

For Style Z wiring, make the following connec-

tions:

• Connect terminals 1 and 4 in one cable going

out to Riser 1.

•

Connect terminals 2 and 3 in another cable

coming back from the last destination of

Riser 1.

• The other audio risers connect in a similar

fashion.

For Style Y connections, use only one cable.

Refer to Figure 3 for details.

Figure 1

TBM-2 Termination Block Module

Figure 2

Mounting the TBM-2

NOTE:

In a Remote Extender

enclosure, a PS-5N7 is

mounted above the TBM-2.

1. Before installing the module, mount the

PCB assembly to the mounting bracket

supplied using the four No. 6 screws

provided.

2. Place the TBM-2 assembly face up on the

three threaded studs arranged in a triangle

with TB5, the 15 position terminal block at

the top.

3. Secure the TBM-2 with the three No. 10

nuts provided.

Connect the riser cables to TB5 in the desired style,

using 18-14 AWG twisted, shielded pair. The other

ends of the risers connect to the OCC-1 terminal

block. Refer to the OCC-1 Installation Instructions,

P/N 315-090918, for further details.

For connections to other connectors and terminal

blocks, refer to the appropriate module installa-

tion instructions. (See also Figure 3 or Figure 4,

as appropriate.)

CAUTION: Keep the riser cables away from the AC power lines, the 24 VDC

supply lines, and the wires carrying the amplified audio signals.

Figure 3

TBM-2 Wiring Diagram

(with MMB or PSR)

1234

5678 91011 12 13 14 15

49 50

TB4

TB3

TB1

TB2

DV-100

OR DMC-1

DV-100

OR DMC-1

+-+-

TB5

J2 J3

NC NC

NO NOC C

14 14

TELEPHONE

RISER +

TELEPHONE

RISER -

TELEPHONE

RISER SHIELD

24V DC +

24V DC RETURN

TO ACM-1, P2

50 CONDUCTOR

RIBBON CABLE

TO VSM-1/VLM-1/VFM-1 MODULES

4 WIRE CABLE

TO ACM-1, P3

TO TMM-1, P1

5 WIRE CABLE

4 WIRE CABLE

NO CONNECTIONS

*EOL

CONNECTION AT FIRST OCC-1 TERMINAL BLOCK

CONNECTION AT SECOND OCC-1 TERMINAL BLOCK

CONNECTION AT LAST OCC-1 TERMINAL BLOCK

AUDIO RISER #1 AUDIO RISER #2

AUDIO RISER #3

CONNECTION AT FIRST OCC-1 TERMINAL BLOCK

CONNECTION AT SECOND OCC-1 TERMINAL BLOCK

CONNECTION AT LAST OCC-1 TERMINAL BLOCK INCLUDES EOL

STYLE Y

STYLE Z

NOT USED

TERMINATED

For Style Z connections, the lines

connected to terminals 1 and 4 are

in one cable. The lines connected

to terminals 2 and 3 are in another

cable. Connect the shield from the

cable connected to terminals 1 and 4.

Telephone Riser

Supervisory Voltage:

15 VDC -

With EOL = 5.6K

and no telephones in

off-hook state.

11 VDC -

With EOL = 5.6K

and one telephone

in off-hook state.

*EOL 10K, 5%, 1/2W

P/N 140-820396

14 AWG SINGLE

CONDUCTOR

14 AWG SINGLE

CONDUCTOR

For all Audio and Telephone Risers

Maximum Loop Resistance: 20 OHMS

Minimum Wire Size: 18 AWG twisted pair, shielded

Maximum Wire Size: 14 AWG twisted pair, shielded

NOTE:

24 VDC IS AVAILABLE ON

THE MMB OR PSR-1

24 VDC IS AVAILABLE ON

THE MMB OR PSR-1

ALL WIRING MUST COMPLY WITH

NATIONAL AND LOCAL CODES

ALL WIRING MUST COMPLY WITH

NATIONAL AND LOCAL CODES

AUX

CTRL 1

AUX

CTRL 2

AUX

OUT1

AUX

OUT 2

Refer to Wiring Specification

for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772

revision 6 or higher, for

additional wiring information.

Audio Riser

Supervisory Voltage:

3.65 VDC nominal

1V RMS AC

POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <50K OHMS FOR TERMINALS 1-14.

P/N 315-093782-9

Figure 4

TBM-2 Wiring Diagram

(with PS-5N7 in an Extender Enclosure)

WARNING

The user must comply with AUX IN and AUX OUT

specifications or the MXLV System may not function

properly. Always complete the full system test to

ensure that all applications function completely.

NOTES

1. All wiring must comply with National and Local codes.

2. For all Audio and Telephone Risers:

Maximum Loop Resistance: 20 ohms

Minimum Wire Size: 18 AWG twisted pair,

shielded

Maximum Wire Size: 14 AWG twisted pair,

shielded

3. Input impedance of AUX IN is 3K ohms, 200mV RMS.

4. The signal source must have isolation using a transformer.

5. The load impedance for AUX OUT must not be less than 10K

ohms, 200mV RMS.

6. The load must have isolation using a transformer.

7. SPDT contacts activate when audio is present on AUX OUT

jacks based on the CSG-M selection of microphone or tele-

phone. Contact ratings: 0.3A at 24 VDC

• If AUX OUT 1 is microphone, then AUX OUT 2 is telephone.

• If AUX OUT 1 is telephone, then AUX OUT 2 is microphone.

8. Refer to Wiring Specification for MXL, MXL-IQ and MXLV

Systems, P/N 315-092772 revision 6 or higher, for additional

wiring information.

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcAAm76

tnerruCeludoMCDV42ybdnatSAm06

Altri manuali Siemens Unità di controllo

Siemens

Siemens SIMATIC IM151-1 STANDARD Manuale utente

Siemens

Siemens 3RA2816-0EW20 Manuale utente

Siemens

Siemens Modem Block Manuale utente

Siemens

Siemens VVG44.15-0.4S Manuale del proprietario

Siemens

Siemens FN2006-U1 Guida

Siemens

Siemens FS-TRI-M Manuale utente

Siemens

Siemens acvatix MVS661 N Series Manuale utente

Siemens

Siemens SINUMERIK 840D sl Manuale del proprietario

Siemens

Siemens SIMATIC FM 351 Manuale utente

Siemens

Siemens CB15 Manuale utente

Siemens

Siemens HCP Manuale utente

Siemens

Siemens SITRANS LU SAM Manuale utente

Siemens

Siemens Add 7 AddFEM Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens SIMATIC S7 Manuale utente

Siemens

Siemens RMB795B Manuale dell'operatore

Siemens

Siemens 4AI I 4WIRE HART Manuale

Siemens

Siemens SIRIUS 3RA2916-1A Manuale utente

Siemens

Siemens SINUMERIK 805 Manuale utente

Siemens

Siemens SINUMERIK 802D sl Manuale del proprietario

Siemens

Siemens LME11 series Manuale utente

Siemens

Siemens S7-1500 PROFIBUS Manuale utente

Siemens

Siemens S5-155U Guida utente

Siemens

Siemens SINUMERIK 840C Guida all'installazione

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente