Siemens SIMATIC ET 200eco PN Documento tecnico
Equipment Manual
I/O device digital outputs
DQ 8x24VDC/0.5A M12-L 8xM12
03/2023Edition
ET 200eco PN M12-L
support.industry.siemens.com
SIMATIC
(6ES7142-6BG00-0BB0)
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E46570894-AD
Ⓟ 03/2023 Subject to change
Copyright © SiemensAG 2020 - 2023.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD
4
Preface
Purpose of the documentation
This equipment manual supplements the ET200ecoPNM12-L Distributed I/O System
(https://support.industry.siemens.com/cs/ww/en/view/109778292) system manual. Functions
that relate in general to the distributed I/O devices ET200ecoPNM12‑L are described in this
system manual.
The MultiFieldbus (https://support.industry.siemens.com/cs/ww/en/view/109773209)
Function Manual describes general MultiFieldbus functions. This equipment manual describes
the specific adaptations for this I/O device.
The information provided in this equipment manual and in the system manual and the
function manuals supports you in commissioning the ET200ecoPNM12‑L distributed I/O
devices.
Changes compared to the previous version
This manual contains the following changes/additions compared to the previous version:
•Supplement to section Parameter data record (Page 63)
•Technical specifications (Page 55) Updated
Conventions
Also observe notes marked as follows:
NOTE
A note contains important information:
• On the product described in the documentation
• On handling the product
• On the part of the documentation to which particular attention is paid
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit (https://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (https://www.siemens.com/cert).
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD 5
Preface
6
1 Guide to ET 200eco PN M12-L............................................................................................................. 8
1.1 Information classes ET 200eco PN M12-L........................................................................... 8
1.2 Basic tools........................................................................................................................ 9
1.3 MultiFieldbus Configuration Tool (MFCT).......................................................................... 11
1.4 SIMATIC Technical Documentation.................................................................................... 12
2 Product overview................................................................................................................................ 14
2.1 Properties ........................................................................................................................ 14
2.2 Operator controls and display elements............................................................................. 16
3 Wiring................................................................................................................................................. 17
3.1 Terminal and block diagram.............................................................................................. 17
3.2 Pin assignment................................................................................................................. 19
4 PROFINET IO........................................................................................................................................ 23
4.1 Parameters/address space................................................................................................. 23
4.1.1 Parameters....................................................................................................................... 23
4.1.2 Explanation of the parameters.......................................................................................... 24
4.1.3 Address space................................................................................................................... 25
4.2 Interrupts/diagnostics alarms............................................................................................ 28
4.2.1 Status and error displays................................................................................................... 28
4.2.2 Interrupts......................................................................................................................... 31
4.2.3 Alarms.............................................................................................................................. 31
4.2.3.1 Diagnostics alarms............................................................................................................ 31
4.2.3.2 Maintenance events.......................................................................................................... 32
5 EtherNet/IP.......................................................................................................................................... 33
5.1 Functions/parameters/address space................................................................................. 33
5.1.1 Supported EtherNet/IP functions....................................................................................... 33
5.1.2 Parameters....................................................................................................................... 34
5.1.3 Explanation of the parameters.......................................................................................... 35
5.1.4 Update time of the I/O data............................................................................................... 35
5.1.5 Address space................................................................................................................... 36
5.2 Diagnostics....................................................................................................................... 41
5.2.1 Status and error displays for EtherNet/IP............................................................................ 41
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD
Table of contents
6 Modbus TCP........................................................................................................................................ 45
6.1 Functions/parameters/address space................................................................................. 45
6.1.1 Supported Modbus TCP functions...................................................................................... 45
6.1.2 Parameters....................................................................................................................... 46
6.1.3 Explanation of the parameters.......................................................................................... 46
6.1.4 Update time of the I/O data............................................................................................... 47
6.1.5 Address space................................................................................................................... 47
6.2 Diagnostics....................................................................................................................... 52
6.2.1 Status and error displays for Modbus TCP.......................................................................... 52
7 Technical specifications...................................................................................................................... 55
A Dimension drawing............................................................................................................................ 62
A.1 Dimension drawing........................................................................................................... 62
B Parameter data record........................................................................................................................ 63
B.1 Dependencies for the configuration.................................................................................. 63
B.2 Structure of data record 128 for I/O device parameter assignment..................................... 63
B.3 Error transferring the data record...................................................................................... 67
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD 7
Table of contents
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD
8
Guide to ET 200eco PN M12-L 1
1.1 Information classes ET 200eco PN M12-L
The documentation for the SIMATIC ET200ecoPNM12-L distributed I/O system is arranged
into three areas.
This arrangement enables you to access the specific content you require.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/de/en/view/109742718).
Basic information
The System Manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATICET200ecoPNM12-L distributed I/O system.
The STEP7 online help supports you in the configuration and programming.
Examples:
•ET200ecoPNM12-L System Manual
•Online help in the TIA Portal
Device information
Equipment manuals contain a compact description of the module-specific information, such
as properties, wiring diagrams, characteristics and technical specifications.
Examples:
•I/O Device Digital Inputs Equipment Manuals
•I/O Device Digital Inputs Equipment Manuals
•I/O Device Digital Inputs/Outputs Equipment Manuals
•IO-LinkMaster I/O Device Communication Module Equipment Manual
•I/O Device Analog Inputs Equipment Manual
General information
The function manuals contain detailed descriptions on general topics relating to the
SIMATICET200ecoPNM12-L distributed I/O system.
Examples:
•Function Manual Diagnostics
•Function Manual Communication
•PROFINET Function Manual
•Function Manual Designing Interference-free Controllers
•IO-Link System Function Manual
•MultiFieldbus Function Manual
1.2 Basic tools
The tools described below support you in all steps: from planning, over commissioning, all
the way to analysis of your system.
TIA Selection Tool
The TIA Selection Tool tool supports you in the selection, configuration, and ordering of
devices for Totally Integrated Automation (TIA).
As successor of the SIMATIC Selection Tools , the TIA Selection Tool assembles the already
known configurators for automation technology into a single tool.
With the TIA Selection Tool , you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/109767888)
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to perform commissioning and maintenance
activities on various SIMATIC S7 stations as bulk operations independent of TIA Portal.
The SIMATIC Automation Tool offers a wide range of functions:
•Scanning of a PROFINET/Ethernet system network and identification of all connected CPUs
•Assignment of addresses (IP, subnet, Gateway) and device name (PROFINET device) to a
CPU
•Transfer of the date and the programming device/PC time converted to UTC time to the
module
•Program download to CPU
•RUN/STOP mode switchover
•CPU localization through LED flashing
•Reading out of CPU error information
•Reading the CPU diagnostic buffer
•Reset to factory settings
•Firmware update of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet.
(https://support.industry.siemens.com/cs/ww/en/view/98161300)
9
Guide to ET 200eco PN M12-L
1.2 Basic tools
I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD
PRONETA
SIEMENS PRONETA (PROFINET network analysis) is a commissioning and diagnostic tool for
PROFINET networks. PRONETA Basic has two core functions:
•In the network analysis, you get an overview of the PROFINET topology. Compare a real
configuration with a reference installation or make simple parameter changes, e.g. to the
names and IP addresses of the devices.
•The "IO test" is a simple and rapid test of the wiring and the module configuration of a
plant, including documentation of the test results.
You can find SIEMENS PRONETA Basic on the Internet:
(https://support.industry.siemens.com/cs/ww/en/view/67460624)
SIEMENS PRONETA Professional is a licensed product that offers you additional functions. It
offers you simple asset management in PROFINET networks and supports operators of
automation systems in automatic data collection/acquisition of the components used through
various functions:
•The user interface (API) offers an access point to the automation cell to automate the scan
functions using MQTT or a command line.
•With PROFIenergy diagnostics, you can quickly detect the current pause mode or the
readiness for operation of devices that support PROFIenergy and change these as needed.
•The data record wizard supports PROFINET developers in reading and writing acyclic
PROFINET data records quickly and easily without PLC and engineering.
You can find SIEMENS PRONETA Professional on the Internet.
(https://www.siemens.com/proneta-professional)
SINETPLAN
SINETPLAN, the Siemens Network Planner, supports you in planning automation systems and
networks based on PROFINET. The tool facilitates professional and predictive dimensioning of
your PROFINET installation as early as in the planning stage. In addition, SINETPLAN supports
you during network optimization and helps you to exploit network resources optimally and to
plan reserves. This helps to prevent problems in commissioning or failures during productive
operation even in advance of a planned operation. This increases the availability of the
production plant and helps improve operational safety.
The advantages at a glance
•Network optimization thanks to port-specific calculation of the network load
•Increased production availability thanks to online scan and verification of existing systems
•Transparency before commissioning through importing and simulation of existing STEP 7
projects
•Efficiency through securing existing investments in the long term and the optimal use of
resources
You can find SINETPLAN on the Internet
(https://new.siemens.com/global/en/products/automation/industrial-
communication/profinet/sinetplan.html).
10 I/O device digital outputs DQ 8x24VDC/0.5A M12-L 8xM12 (6ES7142-6BG00-0BB0)
Equipment Manual, 03/2023, A5E46570894-AD
Guide to ET 200eco PN M12-L
1.2 Basic tools
Altri manuali per SIMATIC ET 200eco PN
12
Indice
Altri manuali Siemens Sistema I/O
Siemens
Siemens SIMATIC SM 335 Manuale utente
Siemens
Siemens SIMATIC ET 200eco PN Documento tecnico
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens Simantic ET 200S Manuale utente
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens SIMATIC ET 200AL Guida utente
Siemens
Siemens SIMATIC ET 200eco PN Manuale utente
Siemens
Siemens simatic ET 200MP Manuale utente
Siemens
Siemens Simatic S7-300 Manuale utente
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens SIMATIC ET 200M Manuale utente
Siemens
Siemens SIMATIC ET 200S Manuale utente
Siemens
Siemens Simatic ET200pro Manuale utente
Siemens
Siemens SIMATIC ET 200S Manuale utente
Siemens
Siemens SIMATIC ET 200SP HA Manuale utente
Siemens
Siemens SIMATIC ET 200eco PN Guida utente
Siemens
Siemens SICAM AI Manuale utente
Siemens
Siemens SIMATIC ET 200S Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
