SIGLENT TECHNOLOGIES SDS1104X-E Manuale utente

SDS1000X-E User Manual

SDS1000X-E Series

Digital Oscilloscope

User Manual

UM0101E-E03B

SDS1000X-E User Manual

WWW.SIGLENT.COM

Trademark Information

SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.

Declaration

SIGLENT products are protected by patent law in and outside of P.R.C.

SIGLENT reserves the right to modify or change parts of or all the specifications or pricing policies

at company’s sole decision.

Information in this publication replaces all previously corresponding material.

Any way of copying, extracting or translating the contents of this manual is not allowed without the

permission of SIGLENT.

Product Certification

SIGLENT guarantees this product conforms to the national and industrial stands in China and

other international stands conformance certification is in progress.

If you have any problem or requirement when using our products, please contact SIGLENT

TECHNOLOGIES CO., LTD

Add：3//F, Bldg No.4, Antongda Industrial Zone, 3rd Liuxian Road, Bao’an District, Shenzhen,

518101, P.R.China

Tel：400-878-0807

E-mail：sales@siglent.com

http://www.siglent.com

SDS1000X-E User Manual

WWW.SIGLENT.COM

Safety Information

General Safety Summary

Carefully read the following safety precautions to avoid any personal injury or damage to

the instrument and any products connected to it. To avoid potential hazards, please use

the instrument as specified.

Use Proper Power Line

Only the power cord designed for the instrument and authorized by local country could be used.

Ground the Instrument

The instrument is grounded through the protective earth conductor of the power line. To avoid

electric shock, please make sure the instrument is grounded correctly before connecting its input

or output terminals.

Connect the Signal Wire Correctly

The potential of the signal wire is equal to the earth, so do not connect the signal wire to a high

voltage.

Look Over All Terminals’ Ratings

To avoid fire or electric shock, please look over all ratings and sign instruction of the instrument.

Before connecting the instrument, please read the manual carefully to gain more information

about the ratings.

Use Proper Overvoltage Protection

Make sure that no overvoltage (such as that caused by a thunderstorm) can reach the product, or

else the operator might expose to danger of electrical shock.

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid damages induced by

static discharge. Always ground both the internal and external conductors of the cable to release

static before connecting.

Keep Well Ventilation

Inadequate ventilation may cause increasing of temperature, which will eventually damage the

instrument. So keep well ventilation and inspect the intake and fan regularly.

Avoid Circuit or Components Exposed

Do not touch exposed contacts or components when the power is on.

Use proper Fuse

Use only the specified fuse.

Do Not Operate Without Covers

Do not operate the instrument with covers or panels removed.

Do Not Operate With Suspected Failures.

If you suspect damage occurs to the instrument, have it inspected by qualified service personnel

before further operations. Any maintenance, adjustment or replacement especially to circuits or

accessories must be performed by SIGLENT authorized personnel.

SDS1000X-E User Manual

III

WWW.SIGLENT.COM

Do Not Operate in Wet Conditions.

In order to avoid short circuiting to the interior of the device or electric shock, please do not

operate in a humid environment.

Do Not Operate in an Explosive Atmosphere.

In order to avoid damages to the device or personal injuries, it is important to operate the device

away from an explosive atmosphere.

Keep Product Surfaces Clean and Dry.

To avoid the influence of dust and/or moisture in air, please keep the surface of device clean and

dry.

Handling Safety

Please handle with care during transportation to avoid damages to buttons, knob interfaces and

other parts on the panels.

Only probe assemblies which meet the manufacturer’s specifications shall be used.

When use 2X/…/10000X probe assemblies, the probe assemblies shall be insulated from the

measured circuits by double or reinforced insulation.

All probe assemblies should meet the requirements of UL 61010-031 and CAN/CSA-C22.2 No.

61010-031-07.

Not to position the equipment so that it is difficult to operate the disconnecting device (detachable

plug).

If the equipment is used in a manner not specified by the manufacturer, the protection provided by

the equipment may be impaired

SDS1000X-E User Manual

WWW.SIGLENT.COM

Safety Terms and Symbols

Terms in this Manual. These terms may appear in this manual:

WARNING

Warning statements indicate the conditions or practices that could

result in injury or loss of life.

CAUTION

Caution statements indicate the conditions or practices that could

result in damage to this product or other property.

Terms on the product. These terms may appear on the product:

DANGER Indicates direct injuries or hazards that may happen.

WARNING Indicates potential injuries or hazards that may happen.

CAUTION Indicates potential damages to the instrument or other property that may happen.

Symbols on the product. These symbols may appear on the product:

Hazardous protective Earth Warning Test Power Switch

Voltage Terminal Ground

If find such symbols on the product, consult the manual to find out the nature of the potential

hazard and the actions which have to be taken

SDS1000X-E User Manual

WWW.SIGLENT.COM

Measurement Category

Measurement Categories

This oscilloscope can make measurements in other circuits that are not directly connected to

mains.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Not to use the product for measurements within other measurement

categories, such as CAT II, CAT III, CAT IV.

Not to use the equipment for measurements on mains circuits

Measurement Category Definitions

Measurement category II is for measurements performed on circuits directly connected to the low

voltage installation. Examples are measurements on household appliances, portable tools and

similar equipment.

Measurement category III is for measurements performed in the building installation. Examples

are measurements on distribution boards, circuit-breakers, wiring, including cables, bus-bars,

junction boxes, switches, socket-outlets in the fixed installation, and equipment for industrial use

and some other equipment, for example. Stationary motors with permanent connection to the

fixed installation.

Measurement category IV is for measurements performed at the source of the low-voltage

installation. Examples are electricity meters and measurements on primary over current

protection devices and ripple control units.

SDS1000X-E User Manual

WWW.SIGLENT.COM

Working Environment

Temperature

Operating: 10℃to +40℃

Non-operation:-20℃to +70℃

Humidity

Under +35℃:≤90% relative humidity

+35℃to +40℃: ≤60% relative humidity

WARNING

To avoid short circuit inside the instrument or electric shock, please do not operate in

humid environment.

Altitude

Operating: less than 3 Km

Non-operation: less than 15 Km

Degree of protection

IP20

Installation (overvoltage) Category

This product is powered by mains conforming to installation (overvoltage) category II.

WARNING

Make sure that no overvoltage (such as that caused by thunderbolt) can reach the

product, or else the operator might expose to danger of electric shock.

Installation (overvoltage) Category Definitions

Installation (overvoltage) category I refers to signal level which is applicable to equipment

measurement terminals connected to the source circuit. In these terminals, precautions are done

to limit the transient voltage to the corresponding low level.

Installation (overvoltage) category II refers to the local power distribution level which is applicable

to equipment connected to the AC line (AC power).

Ventilation Requirement

This oscilloscope uses fan to force cooling. Please make sure that the air intake and exhaust

areas are free from obstructions and have free air. When using the oscilloscope in a bench-top or

rack setting, provide at least 10 cm clearance beside, above and behind the instrument for

adequate ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would damage the

instrument. So please keep the instrument well ventilated during operation and

inspect the intake and fan regularly.

SDS1000X-E User Manual

VII

WWW.SIGLENT.COM

General Care and Cleaning

Care

Do not store or leave the instrument in direct sunshine for long periods of time.

WARNING

To avoid damages to the instrument or probe, please do not leave them in fog, liquid,

or solvent.

Cleaning

Please perform the following steps to clean the instrument and probe regularly according to its

operating conditions.

1. Disconnect the instrument from all power sources, and then clean it with a soft wet cloth.

2. Clean the loose dust on the outside of the instrument and probe with a soft cloth. When

cleaning the LCD, take care to avoid scarifying it.

WARNING

To avoid damages to the surface of the instrument and probe, please do not use any

corrosive liquid or chemical cleanser.

WARNING

Make sure that the instrument is completely dry before restarting it to avoid short

circuits or personal injuries.

SDS1000X-E User Manual

VIII

WWW.SIGLENT.COM

L'information de sûreté

Résumégénéral de sûreté

Lisez soigneusement les mesures de sécuritésuivantes pour éviter n'importe quelles blessures

ou les dommages àl'instrument et àtous les produits se sont reliés àeux. Pour éviter des risques,

utilisez svp l'instrument comme indiqué.

Employez la ligne àhaute tension appropriée

Seulement le cordon de secteur conçu pour l'instrument et autorisépar le pays local a pu être

employé.

A rectifiél'instrument.

L'instrument est fondu par le conducteur protecteur de terra de la ligne àhaute tension. Pour

éviter la décharge électrique, le conducteur moulu doit être reliéàla terre. Assurez-vous que

l'instrument est fondu correctement avant de relier ses bornes d'entrée ou de rendement.

Reliez le fil de signal correctement.

Le potentiel de l'au sol de fil de signal est égal àla terre, ainsi ne relie pas le fil de signal àune

tension.

Regardez estimations au-dessus de toutes les bornes des'

Pour éviter le feu ou la décharge électrique, regardez svp au-dessus de toutes les estimations et

instruction de signe de l'instrument. Avant de relier l'instrument, lisez svp le manuel

soigneusement pour obtenir plus d'informations sur les estimations.

Employez la protection appropriée de surtension

Assurez-vous qu'aucune surtension (comme cela provoquépar un orage) ne peut atteindre le

produit, ou bien l'opérateur pourrait exposer au danger du choc électrique.

Empêchement électrostatique

Fonctionnez dans un environnement protecteur de secteur de décharge électrostatique pour

éviter des dommages induits par décharge statique. A toujours rectifiéles conducteurs internes et

externes du câble pour libérer la charge statique avant de se relier.

La ventilation insatisfaisante de ventilation

bonne de subsistance peut causer l'augmentation de la température, qui endommagera par la

suite l'instrument. Gardez ainsi la ventilation bonne et inspectez la prise et éventez régulièrement.

Évitez le circuit ou les composants exposés

ne touchent pas les contacts ou les composants exposés quand le courant passe.

Employez l'utilisation appropriée

de fusible seulement le fusible indiqué.

Ne fonctionnez pas sans couvertures

n'actionnent pas l'instrument des couvertures ou des panneaux étant coupés.

Ne fonctionnez pas avec des échecs suspectés.

Si vous suspectez les dommages se produisent àl'instrument, l'ont inspectépar le personnel de

SDS1000X-E User Manual

WWW.SIGLENT.COM

service qualifiéavant d'autres opérations. N'importe quel entretien, ajustement ou remplacement

particulièrement aux circuits ou aux accessoires doivent être exécutés par le personnel autorisé

par SIGLENT.

Ne fonctionnez pas en conditions humides.

Afin d'éviter de court-circuiter àl'intérieur du dispositif ou de la décharge électrique, svp ne

fonctionnez pas dans un environnement humide.

Do Not Operate in an Explosive Atmosphere.

Ne fonctionnez pas dans une atmosphère explosive.

Afin d'éviter d'endommager le dispositif ou les blessures, il est important d'utiliser le dispositif loin

àpartir d'une atmosphère explosive.

Maintenez les surfaces de produit propres et sèches.

Pour éviter l'influence de la poussière et/ou de l'humiditéen air, maintenez svp la surface du

dispositif propre et sèche.

En manipulant la sûreté

manipulez svp avec soin pendant le transport pour éviter d'endommager des boutons, des

interfaces de bouton et d'autres parties sur les panneaux.

Sondez seulement les ensembles qui répondent aux caractéristiques du fabricant seront

employés.

Quand des sondes de l'utilisation 5X/10X/50X/100X/500X/1000X, les sondes seront isolées des

circuits mesurés par le double ou l'isolation renforcée.

Toutes les sondes devraient répondre aux exigences de l'UL 61010-031 et du CAN/CS A-C22.2

No. 61010-031-07

Le corps ou l'opérateur responsable devrait se référer au manuel d'instruction pour préserver la

protection se permettent par l'équipement. Si l'équipement est utilisé en quelque sorte non

indiquépar le fabricant, la protection fournie par l'équipement peut être altérée.

On ne permet à aucune pièce du dispositif et de ses accessoires d'être changéou remplacé,

autre qu'autorisépar le fabricant ou son agent.

Pas placez l'équipement de sorte qu'il soit difficile d'utiliser le dispositif débranchant (prise

détachable).

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SIGLENT TECHNOLOGIES Apparecchiature di prova

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS3000X HD Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SHS800 Series QS03008-E01 Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SHS800 Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS2000X HD Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1202X-E Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000CFL Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000 Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6204A Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS2000X-E Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6000A Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS5000X Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000DL Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS6000A Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000X-E Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SAP2500D Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS800X HD Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS5000X Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS1000X Series Manuale utente

SIGLENT TECHNOLOGIES

SIGLENT TECHNOLOGIES SDS2000 Series Manuale dell'operatore

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente