SIGLENT SDS2000X-E Series Manuale utente

SDS2000X-E Series

Super Phosphor

Oscilloscope

Quick Start

SDS2000X-E Series Digital Oscilloscope -I

Declaration

SIGLENT products are protected by patent law in and outside of P.R.C.

SIGLENT reserves the right to modify or change parts of or all the specications or pricing policies at company’s sole decision.

Information in this publication replaces all previously corresponding material.

Any way of copying, extracting or translating the contents of this manual is not allowed without the permission of SIGLENT.

Note: SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.

Information

SIGLENT TECHNOLOGIES CO., LTD.

Address: Blog No.4 & No.5, Antongda Industrial Zone, 3rd Liuxian Road, Bao'an District, Shenzhen, 518101, China.

Tel:+86-755-36615186

E-mail:[email protected]

Http://www.siglent.com

II- SDS2000X-E Series Digital Oscilloscope

Carefully read the following safety precautions to avoid any personal injury

or damage to the instrument and any products connected to it. To avoid

potential hazards, please use the instrument as specied.

Use Proper Power Cord

Only the power cord designed for the instrument and authorized by local

country could be used.

Ground the Instrument

The instrument is grounded through the protective earth conductor of the

power cord. To avoid electric shock, please make sure the instrument is

grounded correctly before connecting its input or output terminals.

Connect the Signal Wire Correctly

The potential of the signal wire ground is equal to the earth, so do not

connect the signal wire to a high voltage.

Look Over All Terminals’ Ratings

To avoid re or electric shock, please look over all ratings and sign instruction

of the instrument. Before connecting the instrument, please read the manual

carefully to gain more information about the ratings.

Use Proper Overvoltage Protection

Make sure that no overvoltage (such as that caused by a thunderstorm) can

reach the product, or else the operator might expose to danger of electrical

shock.

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid

damages induced by static discharge. Always ground both the internal and

external conductors of the cable to release static before connecting.

Keep Well Ventilation

Inadequate ventilation may cause increasing of temperature, which may

eventually damage the instrument. So keep well ventilation and inspect the

intake and fan regularly.

Avoid Circuit or Components Exposed

Do not touch exposed contacts or components when the power is on.

Use Only the Specied Fuse

Do Not Operate Without Covers

Do not operate the instrument with covers or panels removed.

General

Safety

Summary

SDS2000X-E Series Digital Oscilloscope -III

Warning Hazardous

Voltage

Protective

Earth Ground

Earth

Ground

Chassis

Ground

Symbols on the product. These symbols may appear on the product:

Safety Terms and Symbols

Terms on the product. These terms may appear on the product:

DANGER

WARNING

CAUTION

General Care and Cleaning

Care

Do not store or leave the instrument in direct sunshine for long periods of

time.

Notice:

To avoid damages to the instrument or probe, please do not leave them in

fog, liquid, or solvent.

Cleaning

Please perform the following steps to clean the instrument and probe

regularly according to its operating conditions.

1. Disconnect the instrument from all power sources, and then clean it with

a soft wet cloth.

2. Clean the loose dust on the outside of the instrument and probe with a

soft cloth. When cleaning the LCD, take care to avoid scratching it.

Notice:

To avoid damages to the surface of the instrument and probe, please do not

use any corrosive liquid or chemical cleanser.

Make sure that the instrument is completely dry before restarting it to avoid

short circuits or personal injuries.

Indicates direct injuries or hazards that may happen.

Indicates potential injuries or hazards that may happen.

Indicates potential damages to the instrument or other property

that may happen.

1- SDS2000X-E Series Digital Oscilloscope

Contents

Copyright Information............................................................................................................................................

General Safety Summary........................................................................................................................................

Quick start............................................................................................................................................................

The Front Panel ....................................................................................................................................................

The Rear Panel......................................................................................................................................................

Front Panel Overview.............................................................................................................................................

User Interface.......................................................................................................................................................

Using Security Lock................................................................................................................................................

Troubleshooting.....................................................................................................................................................

Contact SIGLENT...................................................................................................................................................

SDS2000X-E Series Digital Oscilloscope -2

Quick Start

General Inspection

1. Inspect the shipping container

Keep the damaged shipping container or

cushioning material until the contents of the

shipment have been completely checked and

the instrument has passed both electrical and

mechanical tests.

The consigner or carrier will be responsible

for damages to the instrument resulting from

shipment. SIGLENT would not provide free

maintenance or replacement if the instrument

has been damaged in shipment.

2. Inspect the instrument

If there are instruments found damaged,

defective or failure in electrical and mechanical

tests, please contact SIGLENT.

3. Check the accessories

Please check the accessories according to the

packing list. If the accessories are incomplete

or damaged, please contact your SIGLENT sales

representative.

Scope Front View

Scope Top View

3- SDS2000X-E Series Digital Oscilloscope

Quick Start

Adjust the Supporting Legs

Adjust the supporting legs properly to use them as stands to tilt the

oscilloscope upwards for stable placement as well as easier operation and

observation of the instrument.

Connect to AC Power Supply

The oscilloscope accept 100-240V, 50/60/440Hz AC power supply. Please

use the power cord provided as accessories to connect the instrument to the

power source as shown in the gure below.

Note: If at any time the fuse requires replacement, please replace only

with a fuse of the same rating as the original. If there are questions, please

contact Siglent directly.

Before adjusting After adjusting To Connect to Power Supply

Power

Socket

SDS2000X-E Series Digital Oscilloscope -4

Power-on Inspection

When the scope is energized, turn on the power switch at the lower left corner on the front panel. During the start-up

process, the instrument performs a series of self-test items and you can hear the sound of relay switching. After the

self-test completed, the User Interface displays immediately.

Connect the Probe

SIGLENT provides passive probe for the SDS2000X-E series oscilloscope. Please refer to corresponding Probe User

Manual for detailed technical information.

Connect the probe:

1.Connect the BNC terminal of the probe to one of the channel BNC connector of the front panel.

2.Connect the probe tip to the circuit point to test and the ground alligator clip of the probe to the ground terminal of

the circuit.

Functional Inspection

1. Press to reset the oscilloscope to its factory default setup.

2. Connect the ground alligator clip of the probe to the Ground Terminal on the front panel.

3. Use the probe to connect the CH1 Input Terminal and the Compensation Signal Output Terminal on the front

panel.

4. Press

5. Observe the waveform on the screen. In normal condition, the display should be a square waveform as shown

in the photo to the right.

6. Test the other channels in the same method. If the actual square waveforms does not match that in the photo

shown, please perform “Probe Compensation”.

Note: To avoid electric shock when using the probe, rst please make certain that the insulated wire of the probe

is in good condition, and do not touch the metallic part of the probe when it is connected to a high voltage.

Quick Start

Compensation Signal

Output Terminal

Ground

Terminal

5- SDS2000X-E Series Digital Oscilloscope

Probe Compensation

You should properly compensate the probe at rst use of it. Non-compensated or inadequate compensated probe may cause inaccurate measurement. The

following steps are about probe compensation:

1. Perform step 1, 2 , 3 and 4 of “Functional Inspection”.

2. Check the displayed waveforms and compare them with the following gure.

3. Use a nonmetallic driver to adjust the low-frequency compensation adjustment hole on the probe until the waveform changes to be correct as the gure above.

Quick Start

Under

Compensated

Correctly

Over

Compensated

SDS2000X-E Series Digital Oscilloscope -6

Scope Front

Panel

①WARNING: Non-standard HDMI interface, Siglent device ONLY, or you will damage your devices.

16 17

18 19 21

1. LCD Display

2. Universal Knob

3. Common Function Menus

4. Clear Sweeps

5. Run/Stop

6. Decode

7. Auto Setup

8. Navigate

9. History

10. Default

11. Vertical Control, Math, REF and Digital

12. Horizontal Control

13. Trigger Control

14. Menu on/off

15. Menu Softkey

16. One- Button shortcut for Save

17. Analog Channel

18. Power Button

19. USB Host

20. SBUS Digital Inputs ①

21. Probe Compensation/ Ground Terminal

Altri manuali per SDS2000X-E Series

Indice

Altri manuali SIGLENT Apparecchiature di prova

SIGLENT

SIGLENT SDS1000X+ Series Manuale utente

SIGLENT

SIGLENT SDS2000X Series Manuale utente

SIGLENT

SIGLENT SDS5052X Manuale utente

SIGLENT

SIGLENT SDS1000CFL Series Manuale utente

SIGLENT

SIGLENT SDS2000 Series Manuale utente

SIGLENT

SIGLENT SDS7000A Series Manuale utente

SIGLENT

SIGLENT SHS800X Series Manuale utente

SIGLENT

SIGLENT SDS1000X Series Manuale utente

SIGLENT

SIGLENT SDS1000CFL Series Manuale utente

SIGLENT

SIGLENT SHS800 series Manuale utente

SIGLENT

SIGLENT SDS1102X Manuale utente

SIGLENT

SIGLENT SDS1000X-E Series Manuale utente

SIGLENT

SIGLENT SDS5000X Series Manuale utente

SIGLENT

SIGLENT SDL1000X Manuale utente

SIGLENT

SIGLENT SDS5000X Series Manuale utente

SIGLENT

SIGLENT SDS2000X Plus Series Manuale utente

SIGLENT

SIGLENT SDS5000X Series Manuale utente

SIGLENT

SIGLENT SDS1000X-E Series Manuale utente

SIGLENT

SIGLENT SDS1004X-E Series Manuale utente

SIGLENT

SIGLENT SDS2304X Manuale utente

SIGLENT

SIGLENT SDG Series Istruzioni operative

SIGLENT

SIGLENT SDS1000 Series Manuale utente

SIGLENT

SIGLENT SDS2354X HD Manuale utente

SIGLENT

SIGLENT SDS1022DL Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente