SIGMA TEK EZ 102 Manuale utente

EZ 102

S-DIAS Digital Output Module

Instruction Manual

Date of creation: 21.07.2015

Version date: 26.07.2023

Article number: 20-051-102-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instruction

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS DIGITAL OUTPUT MODULE EZ 102

26.07.2023 Page 1

S-DIAS Digital Output Module EZ 102

with 10 short-circuit proof outputs

The S-DIAS EZ 102 digital output module has 10 short-circuit proof,

galvanically isolated, digital outputs in 2 groups (+24 V/100 mA). The

power supply for each group is monitored for under voltage.

The EZ 102 is used for the implementation of the Euromap interface.

EZ 102 S-DIAS DIGITAL OUTPUT MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Digital Output Specification.......................................................13 
5.2 Electrical Requirements.............................................................13 
5.3 Voltage Monitor...........................................................................15 
5.4 Miscellaneous .............................................................................15 
5.5 Environmental Conditions.........................................................15 
6Mechanical Dimensions........................................................16 

 S-DIAS DIGITAL OUTPUT MODULE EZ 102 
 
07.2023 Page 3 
7Connector Layout..................................................................17 
1 Status LEDs.................................................................................18 
2 Applicable Connectors...............................................................18 
3 Label Field...................................................................................19 
8Wiring.....................................................................................20 
1 Wiring Example...........................................................................20 
2 Wiring Diagram EUROMAP Interface........................................21 
3 General Information on the Digital Outputs.............................22 
4 Note..............................................................................................23 
9Assembly/Installation ...........................................................24 
1 Check Contents of Delivery.......................................................24 
2 Mounting......................................................................................25 
Addressing.............................................................................27 
Supported Cycle Times ........................................................28 
1 Cycle Times below 1 ms (in µs).................................................28 
2 Cycle Times equal to or higher than 1 ms (in ms)...................28 
Hardware Class EZ102..........................................................29 
1 General Information....................................................................30 
2 Digital Outputs 1-10....................................................................30 
3 Communication Interfaces.........................................................30 
Transport/Storage .................................................................31 

EZ 102 S-DIAS DIGITAL OUTPUT MODULE

Page 4 26.07.2023

14 Storage ...................................................................................31

15 Maintenance...........................................................................32

15.1 Service.........................................................................................32

15.2 Repair...........................................................................................32

16 Disposal..................................................................................32

S-DIAS DIGITAL OUTPUT MODULE EZ 102

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x EZ 102

EZ 102 S-DIAS DIGITAL OUTPUT MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS DIGITAL OUTPUT MODULE EZ 102

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

EZ 102 S-DIAS DIGITAL OUTPUT MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Indice

Altri manuali SIGMA TEK Unità di controllo

SIGMA TEK

SIGMA TEK STO 081 Manuale utente

SIGMA TEK

SIGMA TEK KL 180 Manuale utente

SIGMA TEK

SIGMA TEK CP 101 Manuale utente

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Manuale utente

SIGMA TEK

SIGMA TEK PIM 021 Manuale utente

SIGMA TEK

SIGMA TEK VI 021 Manuale utente

SIGMA TEK

SIGMA TEK SCP 111 Manuale utente

SIGMA TEK

SIGMA TEK DIAS-Drive 2000 Manuale utente

SIGMA TEK

SIGMA TEK SDM 081 Manuale utente

SIGMA TEK

SIGMA TEK PW 022 Manuale utente

SIGMA TEK

SIGMA TEK ST 011 Manuale utente

SIGMA TEK

SIGMA TEK SCP 111-S Manuale utente

SIGMA TEK

SIGMA TEK CCP 531 Manuale utente

SIGMA TEK

SIGMA TEK DC 061-1 Manuale utente

SIGMA TEK

SIGMA TEK MDD 111-2 Manuale utente

SIGMA TEK

SIGMA TEK S-DIAS PS 101 Manuale utente

SIGMA TEK

SIGMA TEK BL 011 Manuale utente

SIGMA TEK

SIGMA TEK TO 161 Manuale utente

SIGMA TEK

SIGMA TEK SRO 021 Manuale utente

SIGMA TEK

SIGMA TEK EZ 101 Manuale utente

SIGMA TEK

SIGMA TEK SDM 081 Manuale utente

SIGMA TEK

SIGMA TEK AO 046 Manuale utente

SIGMA TEK

SIGMA TEK ST 151 Manuale utente

SIGMA TEK

SIGMA TEK DM 167 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente