SIIG JU-H42B22-S2 Manuale utente

Introducing the USB 2.0 4-Port Bay Hub

The USB 2.0 4-Port Bay Hub is designed to support USB

2.0 equipped PC computers. This USB 2.0 hub expands

USB connectivity to your computer.

Features and Benefits

• Compliant with USB Specifications, Revision 2.0

• Drive bay design adds ports to the front of your

computer for convenient device connection

• Fitsintoeither3.5"or5.25"(withincludedmounting

rack) drive bay

• Provides 4 downstream ports for USB device

connections

• Supports high-speed (480Mbps), full-speed

(12Mbps), and low-speed (1.5Mbps) data transfer

modes

• Per port over-current detection and protection

• Supports simultaneous operation of multiple

high-speed USB 2.0 and USB 1.1 devices

• Hot-swappingfeature allows youto attach/detach

USB devices without powering your computer off

Note: USB 1.1 devices are limited to USB 1.1

speeds even when they are connected to a USB 2.0

host adapter or USB 2.0 hub.

USB 2.0 4-Port Bay Hub

Quick Installation Guide

04-0252C

System Requirements

• PC computer with one available internal USB 2.0

port

• One empty 3.5" or 5.25" drive bay

• Windows98SE/ME/2000/XP (32-/64-bit)/Server

2003 (32-/64-bit)/Vista (32-64-bit)

PackageContents

•USB 2.0 4-Port Bay Hub

• "Y" split power cable

• USB 2.0 cable

• 5.25" mounting rack

• Bag assorted holding screws

• Quick installation guide

Hub Layout

Important: The bay hub is shown in white in this

manual. However, it is available in either black or white

depending on the model purchased.

Figure 1. Hub layout

Downstream Ports

Upstream Port

(Root Port)

Power

Connector

5.25" Mounting Rack Assembly

Important: Use the Mounting Rack Assembly only

when installing the hub into a 5.25" drive bay.

Figure 2. 5.25" Mounting Rack Assembly

USB Cable Connectors

Figure 3. USB Cable Connectors

Type A connector Type B connector

Installing the USB 2.0 4-Port Bay Hub

Important: In order for the USB 2.0 4-Port Bay Hub to

work properly, the driver of your existing USB 2.0 host

adapter has to have support for USB 2.0 hubs.

1. Turn OFF the power to your computer and all

connected peripheral devices.

2. Unplug the power cord from the back of the

computer.

3. Remove the computer cover.

4. Select an available 3.5" or 5.25" drive bay for the

USB 2.0 4-Port Bay Hub, remove the cover plate

from the selected drive bay.

Note: When installing the USB 2.0 4-Port Bay Hub

into a 5.25" drive bay install the hub into the 5.25"

mounting rack before mounting into the drive bay

and follow the same assembly instructions. Refer

to 5.25" Mounting Rack Assembly on page 3.

5. Use the included "Y" split power cable and plug in

the mini power connector (same type of power

connector used for the floppy drive) to the USB 2.0

4-Port Bay Hub power connector.

Figure 4. Connecting the Power Connector Cable

6. Connect the Type B connector of USB cable into the

upstream port (root port) of the USB 2.0 4-Port Bay

Hub.

Figure 5. Connecting the USB 2.0 Cable

7. Carefully thread the two cables through the drive

bay opening then push the hub assembly into the

drive bay. Align the hub's screw holes with the

appropriate holes in the drive bay, then carefully

attach the hub to the case using the included

mounting screws. Be careful not to overtighten the

mounting screws.

Mounting

Screw

Figure 6. Mounting the Hub Assembly

8. Connect the Type A connector of the USB cable to

the internal USB 2.0 port in your system.

USB 2.0 Port

Figure 7. Internal USB connection

9. Connect the power connector of the "Y" split power

cable to the system power supply.

10. Replace the computer cover and reconnect the

power cord, then turn the system on.

11. When Windows boots up, the USB 2.0 4-Port Bay

Hub automatically gets detected and installed.

The hub is now ready for device connection.

12. Connect the Type A connector of your USB

device(s) into any of the downstream ports on the

USB 2.0 4-Port Bay Hub.

Technical Support and Warranty

QUESTIONS? SIIG’sOnline Support hasanswers! Simply visitour

web site at www.siig.com and click Support. Our online support

database is updated daily with new drivers and solutions. Answers

toyour questionscould bejust a fewclicks away. Youcan alsosubmit

questions online and a technical support analysts will promptly

respond.

SIIGoffersa lifetime manufacturerwarrantywiththis product. Please

see our web site for more warranty details. If you encounter any

problems with this product, please follow the procedures below.

A) If it is within the store's return policy period, please return the

product to the store where you purchased from.

B) Ifyour purchasehas passedthe store'sreturn policyperiod, please

follow these steps to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, click Support, then RMA to submit a

request to SIIG RMA. If the product is determined to be

defective, an RMA number will be issued. SIIG RMA department

can also be reached at (510) 413-5333.

Step 2: After obtaining an RMA number, ship the product.

•Properly pack the product for shipping. All software, cable(s)

and any other accessories that came with the original package

must be included.

•Clearly write your RMA number on the top of the returned

package. SIIG will refuse to accept any shipping package, and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

•You are responsible for the cost of shipping. Ship the product

to the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

RMA #:

•SIIG will ship the repaired or replaced product via Ground

in the U.S. and International Economy outside of the U.S. at

no cost to the customer.

USB2.04-PortBayHubisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarks

ofSIIG,Inc. MicrosoftandWindowsareregisteredtrademarksofMicrosoftCorporation. Pentium

is a registered trademark of Intel Corporation. Other names used in this publication are for

identificationonly and maybetrademarksof their respectivecompanies.

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading computer upgrade

manufacturer of I/O connectivity products, including PCI & ISA

serial and parallel ports, USB, Serial ATA & UltraATA controllers,

FireWire(1394a/b),networking, sound cards,andotheraccessories.

SIIG is the premier one-stop source of upgrades.

SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly

features, and are backed by an extensive manufacturer warranty.

High-quality control standards are evident by the overall ease of

installation and compatibility of our products, as well as one of the

lowest defective return rates in the industry. SIIG products can be

found in computer retail stores, mail order catalogs, through major

distributors, system integrators, and VARs in the Americas and the

UK, and through e-commerce sites.

PRODUCT NAME

USB 2.0 4-port Bay Hub

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538-3152, USA

Indice

Altri manuali SIIG Interruttore

SIIG

SIIG USB 2.0 Switch Manuale utente

SIIG

SIIG JU-SW2212-S1 Manuale utente

SIIG

SIIG CE-CM0011-S1 Manuale utente

SIIG

SIIG USB 3.0 Manuale utente

SIIG

SIIG AV-GM09Q3-S1 Manuale utente

SIIG

SIIG AV-GM09G3-S1 Manuale utente

SIIG

SIIG AV-GM04P3-S1 Manuale utente

SIIG

SIIG DisplayPort 2-Port KVM Switch Manuale utente

SIIG

SIIG USB Over IP Manuale utente

SIIG

SIIG Hi-Speed USB 4-Port Bay Hub Manuale utente

SIIG

SIIG JU-SC0111-S1 Manuale utente

SIIG

SIIG AV-GM09V3-S1E Manuale utente

SIIG

SIIG USB 3.0 Manuale utente

SIIG

SIIG CE-H24H11-S1 Manuale utente

SIIG

SIIG JU-H70411-S2 Manuale utente

SIIG

SIIG ID-SC0511-S1 Manuale utente

SIIG

SIIG CE-000012-S1 Manuale utente

SIIG

SIIG JU-SC0211-S1 Manuale utente

SIIG

SIIG PC Switch 6000 Manuale utente

SIIG

SIIG USB 2.0 4-Port Bay Hub Manuale utente

SIIG

SIIG JU-SW4112 Manuale utente

SIIG

SIIG USB 2.0+1394 6-Port Bay Hub Manuale utente

SIIG

SIIG CE-KV0011-S2 Manuale utente

SIIG

SIIG CE-KV0612-S1 Scheda informativa del prodotto

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente