Silicon Laboratories TS3300 Manuale utente

UG188: TS3300 EVB User's Guide

A 0.6–3.0 V IN, 1.8–3.6 V OUT, 3.5 µA, High-Efficiency Boost +

Output Load Switch

The demo board for the TS3300 is a completely assembled and tested circuit board that

can be used for evaluating the TS3300. The TS3300 is a power management product

that combines a high-efficiency boost regulator and an output load switch in one pack-

age.

The TS3300 includes an Anti-crush™ feature to prevent the collapse of the input voltage

to the boost regulator when the input is a weak (high impedance) source. If the input

voltage drops below a pre-determined voltage threshold (settable by a resistor divider),

the boost regulator switching cycles are paused, effectively limiting the minimum input

voltage. A pull-down resistor pad is available in order to set the anti-crush voltage.

The TS3300 boost regulator is set to an output voltage of 3.6 V via a resistor divider cir-

cuit. The TS3300 is fully specified over the –40°C to +85°C temperature range and is

available in a low-profile, thermally-enhanced 16-pin 3×3 mm TQFN package with an ex-

posed back-side paddle. The product data sheet and additional documentation can be

found at www.silabs.com.

KEY FEATURES

• Boost Regulator

• Input Voltage: 0.6 V – 3 V

• Output Voltage: 3.6 V

• Shutdown Control Jumper

• Coilcraft 10 µH Inductor

(LPS4018-103ML)

•Resistor Pad Available for Anti-Crush™

Voltage Setting

TS3300 Demo Board (Top View)

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1

1. Functional Description

Boost Regulator Output Voltage Setting

The TS3300 boost regulator is set to an output voltage of 3 V via a resistor divider circuit, as shown in the figure below.

Figure 1.1. Setting the Boost Output Voltage with a Voltage Divider

The output feedback (BO FB) pin is 505 mV. It is recommended to use large resistor values to minimize additional current draw at the

output. Resistors values less than 8 MΩ are recommended. Boost output voltage can be set by solving for R3 for a given R6 value in

the following equation:

R3 =

(

VBO −0.505

)

0.505

To set a 3 V output voltage with R6 = 1.37 MΩ, R3 is calculated to be 6.77 MΩ. A 1% standard resistor value of 6.81 MΩ is selected.

This results in an output voltage of 3.02 V.

Anti-Crush™ Voltage Setting

To set the anti-crush voltage, a feedback pin (BI FB) in conjunction with a voltage divider circuit can be implemented, as shown in the

figure below. The feedback pin voltage is 392 mV. It is recommended to use large resistor values to minimize additional current draw at

the input.

Figure 1.2. Setting the Anti-Crush Voltage with a Voltage Divider

Using the following equation to solve for R1 for a given R2 value, the output voltage can be set:

R1 =

(

VANTI −CRUSH −0.392

)

0.392

To set a 0.8V output voltage with R2 = 1.37 MΩ, R1 is calculated to be 1.42 MΩ. A 1% standard resistor value of 1.37 MΩ is selected.

This results in an anti-crush voltage of 784 mV. The anti-crush voltage is to be set above the minimum input voltage specification of the

TS3300. Refer to the TS3300 Data Sheet “Applications Information” section for more details.

TS3300 Configurations

The TS3300 can be operated in either a Boost Only Configuration or in a Boost + Output Load Switch Configuration. The TS3300

Demo Board is designed so that both circuit configurations can be evaluated. Two sets of Quick-Start Procedures are provided, detail-

ing how to evaluate each circuit configuration. If the Output Load Switch is not needed, it is recommended to use the Boost Only Con-

figuration, since the lowest quiescent current is achievable this way.

UG188: TS3300 EVB User's Guide

Functional Description

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1 | 1

2. Quick-Start Procedure

2.1 Required Equipment

• TS3300 Demo Board

• 1.2 V Battery or Power Supply

• Two Digital Multimeters

• Oscilloscope

2.2 Boost + Output Load Switch Configuration

To evaluate the Boost + Output Load Switch configuration, the following steps should be performed:

1. Connect Jumper J1 LOW. The pin should be connected to the Lo pin, otherwise PCB ground.

2. Connect the provided Jumper so that the REGIN pin is connected to the BOOST_OUT pin.

3. Connect Jumper J3 LOW. The REGEN pin should be connected to the Lo pin, otherwise PCB ground.

4. Connect the battery positive terminal to the test point labeled BOOST_IN. Connect the negative terminal of the battery to the test

point labeled GND.

5. To monitor the boost regulator output voltage, connect the positive terminal of the voltmeter to the test point labeled BOOST_OUT.

Connect the negative terminal of the voltmeter to the test point labeled GND. Connect the Oscilloscope probe to the test point la-

beled BOOST_OUT to monitor the output ripple. The BOOST_OUT voltage should be regulated at approximately 3.02 V.

6. To monitor the output load switch voltage, VREGOUT, connect the positive terminal of the voltmeter to the test point labeled REG-

OUT. Connect the negative terminal of the voltmeter to the test point labeled GND. The REGOUT voltage should be regulated at

approximately 3.02 V. Connect the Oscilloscope probe to the test point labeled REGOUT to monitor the output load switch.

7. To disable the Output Load Switch, connect Jumper J3 HIGH. The REGEN pin should be connected to the Hi pin, otherwise RE-

GIN. The output load switch voltage, VREGOUT, should drop to 0 V.

8. To enable the Output Load Switch, connect Jumper J3 LOW. The REGEN pin should be connected to the Lo pin, otherwise PCB

ground. The output load switch voltage, VREGOUT, should be approximately equal to VBOOST_OUT.

Table 2.1. Output Load Switch settings for Boost + Output Load Switch Configuration

Output Load Switch Function

REG FB SW EN REG IN REG EN Function

REG FB, SW EN, REGIN should be connected to BO.

High VREGOUT = GND

(OFF State)

Low VREGOUT = VBO

(ON State)

2.3 Boost Only Configuration

To evaluate the Boost Only configuration, the following steps should be performed:

1. Connect Jumper J1 LOW. The BENb pin should be connected to the Lo pin, otherwise PCB ground.

2. Connect the provided Jumper so that the REGIN pin is connected to the GND pin.

3. Connect Jumper J3 LOW. The REGEN pin should be connected to the LO pin, otherwise PCB ground.

4. Connect REGOUT to PCB Ground.

5. Connect the battery positive terminal to the test point labeled BOOST_IN. Connect the negative terminal of the battery to the test

point labeled GND.

6. To monitor the boost regulator output voltage, connect the positive terminal of the voltmeter to the test point labeled BOOST_OUT.

Connect the negative terminal of the voltmeter to the test point labeled GND. Connect the Oscilloscope probe to the test point la-

beled BOOST_OUT to monitor the output ripple. The BOOST_OUT voltage should be regulated at approximately 3.02 V.

7. To shutdown the boost regulator, connect Jumper J1 HIGH. The BENb pin should be connected to the Hi pin, otherwise

BOOST_IN. The boost output voltage, VBOOST_OUT, should drop to 0 V. The input supply current reduces to 0.1 µA.

UG188: TS3300 EVB User's Guide

Quick-Start Procedure

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1 | 2

3. Schematics

Figure 3.1. TS3300 Demo Board Circuit Schematic

UG188: TS3300 EVB User's Guide

Schematics

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1 | 3

Figure 3.2. Top Silkscreen Figure 3.3. Top Layer #1

Figure 3.4. Top Layer #2 Figure 3.5. Top Layer #3

Figure 3.6. Bottom Layer Figure 3.7. Bottom Silkscreen

UG188: TS3300 EVB User's Guide

Schematics

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1 | 4

4. Ordering / Component List

Table 4.1. TS3300 Ordering Information

Ordering Number Description

TS3300DB TS3300 Demo Board

Table 4.2. TS3300 Component List

Designation Quantity Description

L1 1 10 µH ±20% Shielded Inductor (4×4 mm)

LPS4018-103ML

C1, C4 2 22 µF ±10% capacitor

(X5R) (25 V) (1206) GRM31CR61E226KE15L

C2 1 3.3 nF ±10% capacitor (0603), 445-5084-2-ND

R1, R6 2 1.37 MΩ ± 1% (0805), 311-1.37MCRTR-ND

R3 1 6.81 MΩ ± 1% (0805), 311-6.81MCRTR-ND

U1 1 TS3300

BOOST, BOOST_OUT, REG_OUT, GND (2) 5 Test points

J1, J3, REG_IN 3 Jumper

UG188: TS3300 EVB User's Guide

Ordering / Component List

silabs.com | Smart. Connected. Energy-friendly. Rev. 1.1 | 5

http://www.silabs.com

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA

Smart.

Connected.

Energy-Friendly.

Products

www.silabs.com/products

Quality

www.silabs.com/quality

Support and Community

community.silabs.com

Disclaimer

Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using

or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and

"Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to

make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the

included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses

granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent

of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant

personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in

weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.

Trademark Information

Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,

EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,

ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laborato-

ries Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand

names mentioned herein are trademarks of their respective holders.

Indice

Altri manuali Silicon Laboratories Scheda madre

Silicon Laboratories

Silicon Laboratories C8051F064-EK Manuale utente

Silicon Laboratories

Silicon Laboratories UG524 Manuale utente

Silicon Laboratories

Silicon Laboratories Thunderboard EFM32GG12 Manuale utente

Silicon Laboratories

Silicon Laboratories Si5328-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories Si5346-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories Si5372 Manuale utente

Silicon Laboratories

Silicon Laboratories Si2493/57/34/15/04-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories ITO Film-F800 Manuale utente

Silicon Laboratories

Silicon Laboratories Si5041-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories EFM8 Series Istruzioni operative

Silicon Laboratories

Silicon Laboratories C8051F850 BLDC Manuale utente

Silicon Laboratories

Silicon Laboratories CP2112-EK Manuale utente

Silicon Laboratories

Silicon Laboratories CP2110 Manuale utente

Silicon Laboratories

Silicon Laboratories ToolStick-CapTouchSenseDC Manuale utente

Silicon Laboratories

Silicon Laboratories Si4455 Series Guida

Silicon Laboratories

Silicon Laboratories Si8284-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories Si5342-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories M88 Manuale utente

Silicon Laboratories

Silicon Laboratories Si5347-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories Wizard Gecko WGM110 Wi-Fi Wireless Starter... Istruzioni operative e di manutenzione

Silicon Laboratories

Silicon Laboratories Si80xx-EVB Manuale utente

Silicon Laboratories

Silicon Laboratories CP2120 Manuale utente

Silicon Laboratories

Silicon Laboratories Si3454-KIT Manuale utente

Silicon Laboratories

Silicon Laboratories SLWRB4179B Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente