Simplex 4100 Series Manuale utente

4100/4120-6014 NIC

and 4100/4120-Series Media Modules

Installation Instructions

2001, Simplex Time Recorder Co., Westminster, MA 01441-0001 USA

All specifications and other information shown were current as of publication, and are subject to change without notice.

579-182

Rev. A

This publication describes the installation procedure for the 4100/4120-6014 Network Interface

Card (NIC) and the following media modules:

• 4100/4120-0142 Wired Media Card

• 4100/4120-0143 Fiber Media Card

• 4100/4120-0144 Modem Media Card

Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If

damage is apparent, immediately file a claim with the carrier and notify Simplex.

• 4100 Field Wiring Diagrams 841-731 (power-limited) or 841-995 (non power-limited)

• 4100U System Installation Guide (574-848)

This publication discusses the following topics:

Topic See Page

Cautions, Warnings, and Regulatory Information 2

Introduction to the 4100 Network Interface Card (NIC) 3

Jumper Settings 9

Setting the NIC Daughter Card Address 10

Mounting Media Cards to the NIC 12

Installing Motherboards into 2975-91xx Back Boxes (4100) 13

Installing Motherboards into 2975-94xx Back Boxes (4100U) 14

Installing the Daughter Card 15

Wiring 16

Checkout Procedure 25

Introduction

Inspecting Contents

of Shipment

Documentation

In this Publication

firealarmresources.com

READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation

manual. These instructions must be followed to avoid damage to this product and associated

equipment. Product operation and reliability depends upon proper installation.

ELECTRICAL HAZARD -Disconnect electrical field power when making any internal

adjustments or repairs. Servicing should be performed by qualified Simplex Representatives.

STATIC HAZARD - Static electricity can damage components. Therefore, handle as follows:

• Ground yourself before opening or installing components (use the 553-484 Static Control

Kit).

• Prior to installation, keep components wrapped in anti-static material at all times.

The user is cautioned that any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

In the event of equipment malfunction, all repair should be performed by Simplex Time Recorder

or an authorized agent. It is the responsibility of users requiring service to report the need for

service to our Company or to one of our authorized agents. Service can be facilitated through our

office at:

Simplex Time Recorder

Westminster, MA 01441

Telephone: (978) 731-2500

Cautions, Warnings, and Regulatory Information

Caution to the User

Service

Requirements

firealarmresources.com

The Network Interface Card (NIC) is a slave card that uses the standard 4100 serial bus to

communicate with the master. The NIC connects FACPs in a network, allowing for

communication between each panel via fiber, modem, or twisted shielded pair wire in a Style 7

wiring configuration.

The NIC is designed to be connected in a point-to-point arrangement, so that one wire fault does

not cause the entire system to fail. The point-to-point arrangement provides the most secure and

fault-tolerant wiring possible.

Three types of media boards can be used with the NIC card.

• The Fiber-Optic Media Card can be used for electrically noisy environments or for

connecting externally to other buildings.

• The Modem Media Card is typically used when a large transmission distance is required.

• The Wired Media Card is used in all other types of applications.

Up to two media boards can be plugged into each NIC. The same NIC can use any combination of

two types of media boards. For example, a NIC may have a modem media board connected to port

1 and a fiber-optic media board connected to port 2.

Continued on next page

Introduction to the 4100 Network Interface Card (NIC)

Overview

firealarmresources.com

Figure 1 depicts the 4100-6014 Network Interface Card.

Figure 1. 4100-6014 Network Interface Card

. Continued on next page

Introduction to the 4100 Network Interface Card (NIC), Continued

Illustration

DATA TRANSMIT/

RECEIVE LEDs

(LED2 THROUGH

LED5)

MEDIA CARD

40-PIN

CONNECTORS

(P5, P6)

DATA RATE JUMPER

PORT (P3)

DAT

PROTOCOL

JUMPER POR

(P3)

ADDRESS DIP

SWITCH (SW2)

DIAL-UP

SERVICE

MODEM

CONNECTOR

(

)

RESET SWITCH

(SW1)

MOTHERBOARD

CONNECTOR (P4)

YELLOW LED

(LED1)

firealarmresources.com

The 4100-6014 NIC module has the following LEDs:

LED1 (yellow). Illuminates when

• The host 4100 requests it to illuminate

• A transmission fails

• It is off-line with the 4100 host

• It needs to be configured

LED2 (red). Illuminates when a data ‘0’ is received at the right port.

LED3 (green). Illuminates when a data ‘0’ is transmitted at the right port.

LED4 (red). Illuminates when a data ‘0’ is received at the left port.

LED5 (green). Illuminates when a data ‘0’ is transmitted at the left port.

The following motherboards can be used with the 4100 NIC. All of them use two daughter

cards—the CPU or master controller, and the NIC—except where noted.

• 575-274 Master Motherboard

• 575-275 Class B Motherboard (holds the 4100 NIC by itself)

• 565-161 U.T. Motherboard

• 565-213 U.T. Motherboard with City Connection

• 566-227 CPU Motherboard

Continued on next page

Introduction to the 4100 Network Interface Card (NIC), Continued

NIC Card LED

Indications

Motherboards

firealarmresources.com

There are three modules that can be plugged into the 4100-6014 NIC:

• 4100/4120-0144 Modem Media Card

• 4100/4120-0143 Fiber-Optic Media Card

• 4100/4120-0142 Wired Media Card

Each module is shown below.

Figure 2. The 4100/4120-0144 Modem Media Card

Continued on next page

Introduction to the 4100 Network Interface Card (NIC), Continued

Media Module

Illustrations

RJ-11

CONNECTOR

(P3)

RS232

CONNECTOR

(P1) (USED FOR

PHYSICAL

BRIDGE)

DATA

TRANSMISSION

JUMPER PORT

(P4)

MODEM TYPE

JUMPER PORT

(P5)

STATUS LEDs (LED1, LED2)

40-PIN NETWORK

INTERFACE CARD

CONNECTOR (J1)

firealarmresources.com

Figure 3. The 4100/4120-0143 Fiber-Optic Media Card

RESERVED (TB1)

Figure 4. The 4100/4120-0142 Wired Media Card

Continued on next page

Introduction to the 4100 Network Interface Card (NIC), Continued

Media Module

Illustrations

(continued)

40-PIN NETWORK

INTERFACE CARD

CONNECTOR (J1)

FIBER-OPTIC DATA:

TRANSMIT (U1),

RECEIVE (U2)

40-PIN NETWORK

INTERFACE CARD

CONNECTOR (P1)

firealarmresources.com

The Modem Media Card has the following LEDs:

LED1. Illuminates when the modem goes off-hook in order to connect to the transmission lines.

LED2. Illuminates when the modem receives an external call during dial-up mode.

Refer to Table 1 for electrical and environmental requirements for the 4100 NIC and media cards.

Table 1. Electrical and Environmental Specifications

Electrical Specifications

Network

Interface Card Startup, no media cards: 8 VDC @ 110 mA

Nominal, no media cards: 20 to 32 VDC @ 0 mA

Fiber

Media Card Using 24V power supply: 20 VDC @ 140 mA max.

Using 5V power supply (GCC/NPU): 5 VDC @ 130 mA max.

Modem

Media Card 5 VDC @ 150 mA max.

Wired

Media Card 4.75 to 5.25 VDC @ 170 mA max.

Environmental Specifications

Operating

Temperature 32°to 120°F (0°to 49°C)

Humidity 10% to 93% relative humidity at 90°F (32°C)

Introduction to the 4100 Network Interface Card (NIC), Continued

Modem Media Card

LED Indications

Specifications

firealarmresources.com

The NIC card, along with the fiber, modem, and wired media cards, all have jumpers that must be

set.

There are two shunt jumper ports on the NIC card that need to be set: P3 and P4.

Jumper port P3 on the NIC card determines the data transmission rate, 57.6 kbits/second or 9600

bits/second, that the NIC card is using.

• The 57.6 kbits/second rate is selected when pins 1 and 2 (the right two pins) are

jumpered, or when none of the three pins are jumpered.

• The 9600 bits/second rate is selected when pins 2 and 3 (the left two pins) are jumpered.

Jumper port P4 on the NIC card determines the data protocol, 8-bit or 9-bit, that the NIC card is

using.

• The 9-bit protocol is selected when pins 1 and 2 (the right two pins) are jumpered, or

when none of the three pins are jumpered.

• The 8-bit protocol is selected when pins 2 and 3 (the left two pins) are jumpered.

All settings are labeled on the card.

Jumper port P2 on the wired media card tells the system which wire type is to be used.

• Jumper pins 1 and 2, 5 and 6, and 7 and 8 to specify 18 AWG shielded, twisted pair

wiring.

• Remove all jumpers to specify 24 AWG twisted pair telephone cable wiring.

Jumper ports P4 and P5 on the modem media card tells the system how the card is being used.

On port P4, jumper pins 1 and 2. This sets the card up as a network media card, as opposed to a

stand-alone modem.

On port P5, jumper pins 1 and 2. This specifies that the transmission data comes from the 40-pin

connector (J1) or the 10-pin RS-232 connector (P1).

Jumper Settings

Overview

NIC Card

Jumper Settings

Wired Media Card

Jumper Setting

Modem Media Card

Jumper Settings

firealarmresources.com

Switch SW2 on the 4100 NIC is a bank of eight dip switches. From left to right (see Figure 5,

below) these switches are designated as SW2-1 through SW2-8. The function of these switches is

as follows:

• SW2-1. This switch sets the baud rate for the internal 4100 communications line running

between the card and the 4100 CPU. Set this switch to ON.

• SW2-2 through SW2-8. These switches set the card’s address within the 4100 FACP.

Refer to Table 5 for a complete list of the switch settings for all of the possible card addresses.

Note: You must set these switches to the value assigned to the card by the 4100

Programmer.

18765432

Figure 5. DIP Switch SW2

Continued on next page

Setting the NIC Daughter Card Address

Overview

OFF

Dip Switches SW1-2 through

SW2-8 set the Card Address.

Figure shows an Address of 3.

4100 Comm. Baud Rate.

Switch (SW2-1)

Must Be Set to ON

firealarmresources.com

Altri manuali per 4100 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Simplex Unità di controllo

Simplex

Simplex 4100-5101 Manuale utente

Simplex

Simplex MINIPLEX 4100ES Series Manuale utente

Simplex

Simplex 2050 Manuale utente

Simplex

Simplex 4001-9810 Manuale utente

Simplex

Simplex Foundation Series Manuale utente

Simplex

Simplex 4090-9116 Manuale utente

Simplex

Simplex 4100-6069 Manuale utente

Simplex

Simplex TYCO 4905-9835 Manuale utente

Simplex

Simplex 2004 Series Manuale utente

Simplex

Simplex 4100-6065 Manuale utente

Simplex

Simplex 4100 Series Manuale utente

Simplex

Simplex 2008 Series Manuale utente

Simplex

Simplex 2004 Series Manuale utente

Simplex

Simplex 2050 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente