SinoCon KonNaD C2000-A2-SDXA000-AX1 Manuale utente
Last updated: 2020-3-27
C2000-A2-SDXA000-AX1
User Manual
RS485 ← 16DI
Remote I/O Module — RS485 Digital I/O Module
SinoCon Co., Ltd.
2
4
4
4
5
5
5
7
7
8
9
10
11
11
12
12
12
12
12
12
12
13
13
14
14
15
16
18
18
20
21
21
21
22
23
25
26
Catalog
Catalog
1. Getting Started
1.1. Preparation Before Use
1.2. Wiring
1.3. Software Installation & Device Debugging
1.3.1. Software Installation
1.3.2. Device Debug
2. Hardware Description
2.1. Specifications
2.2. Apprearance
2.3. Indicators
2.4. Port Description
2.5. Product Dimensions
2.6. Installation Method
3. Product Features
3.1. DI Data Acquisition
3.1.1. DI Type
3.2. Other Features
3.2.1. DI Pulse Mode
3.2.2. Filter Parameters
3.2.3. Zeroing
4. Software Tools
4.1. Main Screen
4.2. Use Software
4.2.1. Device Settings
4.2.2. View Device Status
4.2.3. Control Device Status
5. Protocol
5.1. Registers
5.1.1. Baud Rate Code
5.2. Examples
5.2.1. Read DI Status (0x02)
5.2.2. Read DI Filter Parameters (0x03)
5.2.3. Write Single DI Filter Parameters (0x06)
5.2.4. Write DI Filter Parameters (0x0F)
6. Package Contents
7. Warranty Policy
C2000-A2-SDXA000-AX1 User Manual
2 / 26
SinoCon Co., Ltd. www.sinoconsys.com
Copyright Notice
©2000 - 2020 SinoCon Co., Ltd. All Rights Reserved.
Trademarks
The KonNaD logo is a registered trademark of SinoCon Co., Ltd. All other trademarks or registered marks in this
manual belong to their respective manufacturers.
Disclaimer
This document only provides information about KonNaD products. No license to any intellectual property rights is
granted by this document, including any intellectual property licenses, expressed or implied, or by any means.
SinoCon assumes no responsibility other than the liability stated by SinoCon in the terms and conditions of sale of
its products and SinoCon makes no warranties regarding the sale or use of KonNaD products, including the
suitability for the specific use of the products, and marketability, and SinoCon doesn't guarantee that it won't
infringe any patent, copyright or other intellectual property rights, etc.
Information in this document is subject to change without notice and does not represent a commitment on the
part of SinoCon.
Contact US
SinoCon Co., Ltd.
Address: 16th Floor, Tower A, Zhongyin Building, Caitian Road, Futian District, Shenzhen, China
Web: www.sinoconsys.com
Tel: +86 0755-88865168
C2000-A2-SDXA000-AX1 User Manual
3 / 26
SinoCon Co., Ltd. www.sinoconsys.com
1. Getting Started
1.1. Preparation Before Use
You will need the following hardware and software to use the C2000-A2-SDXA000-AX1.
• C2000-A2-SDXA000-AX1 module
• A power source that provides 9 to 27 VDC, and several wires
• A PC running a Windows 7 or later versions, and an Ethernet cable
• KonNaD Settings Utility software, Download
1.2. Wiring
Refer to Port Description for the recommended wires.
Check the following items after the device is powered on：
• The PWR is steady red, and the RUN is flashing, which indicates the device is powered normally.
• Connect the device to the host computer through RS485 to USB converter, and you can acquire the value of DI
Value through the software.
Refer to Indicators for the meaning of LED indicators.
C2000-A2-SDXA000-AX1 User Manual
4 / 26
SinoCon Co., Ltd. www.sinoconsys.com
1.3. Software Installation & Device Debugging
1.3.1. Software Installation
Download the software on "Download" above. Unzip the folder and run KonNaD.Setup.exe as administrator. The
setup wizard will pop up to direct you to complete the installation.
1.3.2. Device Debug
Search Devices
Select Search for serial devices and Click Edit button to set the search parameters:
· COM ID: select the correct port for RS485 to USB;
· Baud rate: default 9600;
· Parity: default None;
· Data bit: default 8;
· Stop bit: default 1;
· Address range: range from 1 to 255, default 1 to 10;
· Timeout interval (ms): default 200.
Click Search to find the device through the port for RS485 to USB.
Note: if no device can be found.
C2000-A2-SDXA000-AX1 User Manual
5 / 26
SinoCon Co., Ltd. www.sinoconsys.com
• Check whether to install and run as administrator ;
• Check whether the RS485 to USB converter is correctly connected to the device and whether the converter is
faulty;
• Check whether the search parameters are correct (default value: 9600 None 8 1, and address is 1).
Communication
Select the device that has been searched, click the Refresh button at the bottom right screen and you can see all
the point value of the device.
· DI1 ~ DI16: The value 0 indicates "Open", the value 1 indicates "Short to GND". Use a wire to short the DI1 and
GND, you can see that the DI1 indicator is on.
As shown below:
Note:
Refer to Software Tools for more detailed information.
Refer to Registers for information on "Secondary Development".
C2000-A2-SDXA000-AX1 User Manual
6 / 26
SinoCon Co., Ltd. www.sinoconsys.com
2. Hardware Description
2.1. Specifications
Classification Parameter Specification
Digital Input DI Channels 16
DI Connector Terminal block
Input Type Dry contact
DI Mode Logic level & pulse count
Digital Filtering Time Interval 6 sample periods
Counter Frequency 1kHz
Upstream Serial Port Serial Standrad RS485
No. of Ports 1
Connector Terminal block
Industrial Protocol Standard Modbus RTU Protocol
Power Power Connector Terminal block
Input Voltage 9~27VDC
Current 80mA @ 12VDC
Physical Characteristics Dimensions 75*105*30mm
Installation Din-rail or wall
Environmental Limits Operating Temperature -40℃ ~ 85℃
Storage Temperature -60℃ ~ 125℃
Ambient Relative Humidity 5% ~ 95% RH, non-condensing
C2000-A2-SDXA000-AX1 User Manual
7 / 26
SinoCon Co., Ltd. www.sinoconsys.com
2.3. Indicators
Classification Indicator Description Meaning
Digital Input DIx Digital input
indicators (dry
contact)
Steady on：Short to GND
Off：Open
Downstream
Serial Port
RXD RS485 data receive
indicator
Steady on：RS485 line fault, please check if the positive
and negative poles of 485 line are reversed
Flashing：RS485 receiving data
Off：RS485 no receiving data
TXD RS485 data
transmit indicator
Flashing：RS485 transmitting data
Off：RS485 no transmitting data
Power PWR Power indicator Steady on：Normal power supply
Off：No power or abnormal power supply, please
check if the voltage range is 9~27VDC
RUN RUN Running indicator Steady on：Device exception
Flashing：Flashes every 1 second when the device is
ready
Off：Device exception
C2000-A2-SDXA000-AX1 User Manual
9 / 26
SinoCon Co., Ltd. www.sinoconsys.com
2.4. Port Description
Classification Port Description Recommended
wiring
Digital Input DIx Digital input RVV 2*0.5
GND Dry contact input common RVV 2*0.5
Upstream Serial
Port
485+、
485-
RS485+, RS485- (upstream) RVSP 2*0.5
Power Input V+、V- Power supply input positive, power supply input
negative
RVV 2*1.0
PE Used for reliable grounding of the device, surge
protection
RVV 2*0.5
C2000-A2-SDXA000-AX1 User Manual
10 / 26
SinoCon Co., Ltd. www.sinoconsys.com
Indice
Altri manuali SinoCon Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
