Input Voltage: 120VAC, 60Hz
Maximum Load: 300W at 120AVC
Operating Frequency: 318MHz
Wiring: Neutral, Live, Load (18 AWG)
10. TECHNICAL SPECIFICATIONS
11. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
12. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
http://www.skylinkhome.com
P/N. 101Z699
Patent Pending
©2010 SKYLINK GROUP
6. BRIGHTNESS CONTROL OPERATION
Besides turning on and off the light, you may also control the brightness
of the light if the light bulb is dimmable, i.e. either incandescent light and
designated dimming compact fluorescent light.
To change the brightness, first turn on the light.
Press and hold the programmed button on the transmitter will change its
brightness. Hold onto the button until the desired brightness is reached,
then release the button.
Press and hold the same button again on the transmitter to change the
brightness again in the opposite way (i.e. Dim to brighten or brighten to
dim), until the desired brightness is reached, then release the button.
7. ZONE OPERATION
Zone Operation On / Off (with the TC Series Deluxe Transmitter)
A Zone Command allows you to operate multiple lights at the same time
in the same zone. You may turn On or Off a zone.
Dimmable Receiver
Module
Dimmable Receiver Module
Dimmable Receiver Module
To activate the zone command, simply press “Zone On” or “Zone Off”,
then the zone number.
A zone command must first be programmed to the
. Follow the programming instructions in Section 3 of the manual
and program the zone command under On / Off Mode. For example, if
you would like to assign the to be one of the
devices in zone 1, you should press [Zone On] and [1] during step 5B
under pro-gramming instruction Section 3. So the Zone 1 signal is
programmed to the .
Pressing [Zone On] then [1] will turn on all lights in zone 1.
Pressing [Zone Off] then [3] will turn off all lights in zone 3.
Zone Operation Brightness Control
You can also change the brightness of all the lights in that zone, if the
receiver modules and lights connected are dimmable.
[Zone On] represents increase in brightness level, i.e. Brightening
[Zone Off] represents decrease in brightness level, i.e. Dimming
Press [Zone On] then hold [1] will brighten all lights in zone 1, release
the button at the desired brightness level or it will stop until they are at
the maximum brightness.
Press [Zone Off] then hold [1] will dim all lights in zone 1, release the
button at the desired brightness level or it will stop until they are at the
minimum brightness.
13. ACCESSORIES
9. ERASING TC TRANSMITTERS FROM THE
DIMMABLE RECEIVER MODULE
Note:
When used with Compact Fluorescent Light, if there is flickering when you
switch off the light, it is recommended you replace a different Compact
Fluorescent Light with higher quality.
On / Off Operation - Original Wall Switch
Power On - Light On
There is a function "Power On - Light On" built-in to the receiver module.
This means when the power supply to the receiver module change from
off to on, this will turn the light on. This function allows you to operate the
light with original wall switch.
When the wall switch is in the off position, switching it on will turn on the
light. Once the switch is on, you may use the remote control to operate
the light.
If the wall switch is switched from on to off, the light will be off. At the
same time, the remote control cannot operate the light cause there is no
power supplied to the receiver module.
In case you do not want to operate the light with the original wall switch,
you can disable this Power On - Light On feature and use only remote
control to operate the light. One incident that the light may be turned on
by accident is after a power failure. If you leave the wall switch on, but
turn off the light with a remote control. When power comes back on, the
light will be on. Therefore, there is an option not to turn the lights on when
power is supplied to the receiver module. The way to disable this feature
is to re-program a transmitter (button) that is already programmed to the
receiver module (i.e. program a transmitter twice). This will disable this
feature. You may re-program it again to toggle the setting between
enabling and disabling this feature.
If the Power On - Light On feature is disabled, the light will not be turned
on under most circumstances, i.e. power comes back up after power
failure, or manually turning on the wall switch. However, you can still turn
on the light by the wall switch with a specific power up sequence, that is
to turn on the wall switch twice within 2 seconds. So in case the remote
control is lost, the light can still be turned on.
5. ON / OFF OPERATION (CONT) 8. ZONE OPERATION (CONT)
The Skylink Lighting System consists of many other devices from
multiple button transmitters, Motion Sensor, various receivers such as
Wall Switch Receiver, Plug-in Receiver with Repeater, Outdoor Receiver,
Dimmer Module etc. Please visit Skylink website at www.skylinkhome.com
for more information.
TM
Home
You may erase a TC transmitter from the Dimmable Receiver Module, but
you cannot erase a specific device, you must erase all the wireless
devices, then program the ones you want to keep. Follow the instructions
below to erase programmed TC transmitters.
1. Power off the lighting receiver. (Switch off the wall switch)
2. Press the PROG button on the back of the TC transmitter.
3. Press and hold the programmed button on the TC transmitter for at
least 2 seconds. Do not release this button until step 5.
4. Power up the lighting receiver (Switch off the wall switch), you will hear
beeping and the light will be on.
5. You may release the button on the transmitter.
6. When the button is release, the light attached to the Dimmable Receiver
Module should be off, indicating you have successfully erased all the
devices from the lighting receiver.
To erase other transmitters or sensors, please refer to the instructions of
the transmitters / sensors.
