SOLINTEG Integ R Series Manuale utente
User Manual
Integ R series DuoCOM module
1
User Manual
ENGLISH VERSION
Integ series
DuoCOM Module
R
User Manual
Integ R series DuoCOM module
2
Product Description
1
※1.1.Product Introduction
DuoCOM module supports both WiFi and LAN connection. At
the same time, it supports both remote and local communication.
phone
Router
LAN
WiFi
When WiFi and LAN are connected at the same time, the communication method
will be prioritized to LAN. if you need to change the communication method to
WiFi, please unplug the network cable, restart DuoCOM or wait for 5 minutes.
If WiFi communication has been configured and used individually beforehand, and
you connect to the LAN again, WiFi communication will still be used at this time. If
you need to change the communication method, restart DuoCOM.
phone
Router
phone
Figure 1-1 Remote server communication
DuoCOM can be used for WiFi or LAN communication alone, or connected both
at the same time. When connected simultaneously, DuoCOM will automatically
switch to another communication method after 5 minutes if the communication
method being used fails.
WiFi
LAN
Figure 1-2 Local configuration app communication
Hybrid inverter software version 01 (18) and above adaptable,
Grid-connected PV inverter software version 00 (05) and above adaptable.
User Manual
Integ R series DuoCOM module
3
※1.2 Product Appearance
Indicator
Button
Figure 1-3 DuoCOM
※1.3 Indicator and Button
Press 1 second : Reset device,the indicator goes off for 2 seconds, then
flashes normally.
Press 5 second : Restore factory default settings, the indicator goes off for 2
seconds, then flashes once every 2 seconds, until the factory
restore is completed.
OFF Connection abnormal
Slowly ashing The DuoCOM is not connected to the router.
Quickly ashing The DuoCOM is connected to the router but not
connected to the seer.
Always on The DuoCOM is normal working.
The device be malfunctioning, if the indicator has been O for more
than 5 minutes.
NOTE
User Manual
Integ R series DuoCOM module
4
Conguration
2
Figure 2-1
※2.1 Install The Network Cable
Plastic NUT
Sealing Ring
RJ45 Plug Ethernet Po(inside)
Step1: Remove the “Plastic Nut” and “Sealing Ring” in turn.
Step2: Pass the network cable plug through the“Plastic Nut” and “Sealing Ring”
(with opening) in the direction as shown in the gure 2-1.
Step3: Fully embed the “Sealing Ring” into the“Plastic Nut”.
Step4: Connect the “RJ45 Plug” to the Ethernet Po(inside) and tighten the
“Plastic Nut” for better waterproong.
Step5: Connect the “DuoCOM” to the “COM1” as shown in the gure 2-2.
Figure 2-2
User Manual
Integ R series DuoCOM module
5
Due to limited space, only RJ45 plug without protective cap can be
used.
The network cable is required to be circular or oval, and the diameter
of the network cable needs to be greater more than 5.5mm and less
than 6.5mm in order to be properly sealed.
NOTE
If you want to remove the network cable, unscrew the plastic case and seal-
ing ring, and use a one-piece screwdriver to press in the way shown below,
then pull out the cable.
Press
Protection cap
Pull
User Manual
Integ R series DuoCOM module
6
※ 2.2LANConguration
If DHCP is enabled on the router, the DuoCOM does not need to be con-
gured. Otherwise, the DuoCOM will need to be congured on inveer
screen.
① Find the “General Settings” by sho pressing the button on the inve-
er screen.
② Enter the “General Settings” by long pressing the button on the inve-
er screen.
③ Find “DHCP set” by short pressing the button, then turn off DHCP
function by sho pressing and long pressing the button on the inveer
screen.
④ Then set the “IP Address”, “Gateway Address”, “Subnet Mask” and “DNS
Address”. Sho press to change the number, long press to conrm the
number and jump to the next number.
User Manual
Integ R series DuoCOM module
7
※ 2.3WIFIConguration
User Manual
Integ R series DuoCOM module
8
7
Wireless operating frequency is only supported from 2.412-2.484
（GHz）.
NOTE
"Connection succeeded" wil
l
displayed if connected
successfully.The indicator of
the WiFi module will be
steady on.
User Manual
Integ R series DuoCOM module
9
※ 2.4LocalcongurationApp
DuoCOM also suppos local congured App.Local conguration App is
designed for quick configuration of hybrid inverters, offering features
such as safety code, batte brand and type, work modes, and o-grid
application settings through WiFi direct connection, etc.
There are two connection modes, WiFi direct connection and router connection.
Connection steps:
① -a. Refer to “WiFi module conguration
guide step1~2” to connect the
smartphone to the WiFi module. If it is
connected, skip this step.
② Open “Setup APP”，tap“Scan”，a list of inveer WiFi-AP names pop up.
③ Click and select the inveer WiFi-AP which you want to connect.
④ Select the login role.
⑤ Input the password(123456)，tap“Login In”.
⑥ If connected and logined, the Setup APP main inteace will be displayed.
① -b. Refer to “WiFi module
configuration guide” or “LAN module
configuration guide” to connect the
DuoCOM to the router. Then connect
smartphone to the same router. If it is
connected, skip this step.
Smartphone connects WIFI monitoring
device directly.
Smaphone and the monitoring device
are connected to the router together.
phone
Router
LAN
phone
User Manual
Integ R series DuoCOM module
10
Should you have any question about this product, please contact us.
We need the following information to provide you the best assistance:
• Model of the device
• Serial number of the device
• Brief description of the problem
China (HQ)
Solinteg Power Co., Ltd.
Address: Building H1-1001, No. 6 Jingxian Road, Xinwu District, 214135
Wuxi, Jiangsu Province, China
Website: www.solinteg.com
Seice Mail: seice@solinteg.com
3 Contact Information
Indice
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
