SOMFY Sonesse 30 rts Manuale di installazione

Sonesse 30 RTS Programming Instrucons

Power Supply 24V DC

Frequency bands 433.42 MHz

Torque 2 Nm

Speed 6—28 RPM (Adjustable)

Safety level III

Operang Temperature 32F—140F

Protecve rang IP 30 (For indoor use only)

FCC Compliance

This device complies with Part 15 of the FCC rules. Operang is subject to the following two

condions

[1] This device may not cause harmful interface, and

[2] This device must accept any interference received, including interference that may cause

undesired operaon.

Stripe = Posive

White = Negave

18-2204-SRF

Installaon notes

Make sure that the program buon on the motor head is posioned in the instal-

laon brackets so it is easily accessible. Ideally on an open roll installaon, the

motor head buon should be facing downwards towards the oor so you can see

it. If it is in a cassee then Lafayee will already have the motor installed in the

cassee to make it easy for you to get to. You will be required to press/hold this

buon during the programming sequence or to reset the motor.

Transmier informaon

STOP

DOWN

STOP

DOWN

LED

Indicator

Light

Single Channel

Ver-

LED Lights

Channel

Selector

Five Channel

Version

Back View

Programming

Buon

LED

Indicator

Program

Buon

LED

Indicator

Channel

Selector

Buon(s)

Channel

Selector

Buon(s)

STOP Buon

UP Buon

DOWN

Buon

A) Remotes

B) Wireless

Wall Switch

STOP

DOWN

LED

Indicator

Light

STOP

DOWN

LED Lights

Channel

Selector

DOWN

LED Lights

Channel

Selector

STOP Programming

Buon

Scroll Wheel

Programming (Follow steps 1—5)

[1] Inial setup

A) Connect your proper power source. If you are powering the motor via

a transformer or hardwiring, connect the wires according to your state and local

wires codes.

B) Your motor has been programmed with limits. You will need to pair your motor to your remote.

Please go to secon [6] Pairing.

[2] Pair motor to transmier (only aer full reset)

If you have a mul-channel remote, please select the

appropriate channel you are wanng this shade to be on. Then

press and hold the UP and DOWN buon for a jog then release.

Proceed to step [3] if you get a jog. If the shade does not jog

check your power. Try step [2] again. If you sll don’t get any

response please proceed to step [6].

[3] Checking motor direcon

Press the UP buon on your controller

a) If the shade goes up then proceed to step [4]

b1) if the shade starts to go down then press and hold

The MY buon unl the shade starts to jog.

b2) conrm direcon is correct

Proceed to step [4]

Programming (Connued)

[5] Finalize programming

Press and release the program buon on your transmier with a

small pped utensil and your shade should jog.

Lafayee dealer technical support call: 877-548-0612

[4] Seng limits

1) Move the shade to your desired upper limit. You must hold a

direcon in order for your shade to move right now.

2) Press both MY and DOWN at the same me unl the shade

starts to lower then release both buons.

3) Stop the shade with the MY buon once your shade has

reached your desired lower limit (adjust as needed. The shade

will only move while you HOLD a direcon. Press the UP or

DOWN buon to adjust to your desired lower limit).

4) Press both MY and UP at the same me unl the shade starts

to raise then release both buons.

5) The shade will stop by itself at the top. Once the shade has

stopped hold the MY unl the shade starts to jog then release.

Pairing

[6] Pairing motor informaon to a transmier

a) Hold the white motor head buon for 1 jog then release.

b) Press and release the program buon on your transmier for a jog.

Test your limits and ensure limits are properly set. If you need to adjust

please go to step [7—8].

c) If the shade will only move when you hold a direcon proceed to step

[3]

*** There is no automac ALL channel. You must repeat this step every me you are adding the motor to an

addional channel ***

Erasing motor sengs

[9] Erase all motor sengs

*** Doing this will delete all motor limits and any remotes that

was programmed to this motor ***

Press and hold the white motor head buon for 3 connuous jogs.

You will now need to go to step [2].

Lafayee dealer technical support call: 877-548-0612

Adjusng end limits

[7] Adjusng UPPER limit

1) Press and release UP. Let the shade go to its CURRENT upper

limit and stop.

2) Hold both UP and DOWN at the same me for a jog.

3) Adjust the shade with the UP or DOWN buon to your new limit.

The shade will only move when you HOLD a direcon.

4) Hold the MY buon for a jog.

[8] Adjusng LOWER limit

1) Press and release DOWN. Let the shade go to its CURRENT lower

limit.

2) Hold UP and DOWN at the same me for a jog.

3) Adjust the shade with the UP or DOWN buon to your new limit.

The shade will only move when you HOLD a direcon.

4) Hold the MY buon for a jog.

Favorite posion

[10] Seng your favorite posion

1) Move shade to your desired favorite posion

2) Hold the MY buon

To go to your favorite posion just press and release the MY buon

Troubleshoong Secon

What is happening Possible x

Motor does not respond Reverse the wiring on the motor.

Shade is skipping / clicking while it travels 1) The motor drive is not put into the tube correctly. Remove

the motor and ensure the drive is put in the correct orienta-

on

2) The shade is too ght in the brackets. Ensure you have a free

gap on the idler end.

3) You need a new crown/drive kit

Shade is making a vibrang sound You need to adjust/shim your installaon brackets for the shade

Shade squeaks while it travels Lubricate the idler end plug.

Shade will only move while I hold a direcon 1) If you were adjusng a limit from user mode, you just need

to conrm your new limits. Move the shade to where you

wanted the new limit and then press and HOLD the MY

buon for a jog

2) The motor is sll in programming mode. Please go back to

step [3] under Programming.

3) If none of those opons work, reset the motor and start

over. Go to step [9] Erasing Motor Sengs

Motor keeps loosing its limits This will happen if the motor was not nalized during the

programming process. Completely reset the motor. Go Erasing

Motor Sengs step [9].

Altri manuali per sonesse 30 rts

Indice

Altri manuali SOMFY Motore

SOMFY

SOMFY GOME MOTION Roll Up 28 WT Manuale utente

SOMFY

SOMFY Sonesse 30 PoE Manuale utente

SOMFY

SOMFY BAT-R Manuale di installazione

SOMFY

SOMFY RDO 50 CSI Manuale utente

SOMFY

SOMFY Tilt & Lift 25 RTS Central Manuale utente

SOMFY

SOMFY Sonesse 30 PoE Istruzioni operative

SOMFY

SOMFY PHOENIX PH 30/14 Manuale utente

SOMFY

SOMFY RDO 50 CSI Manuale utente

SOMFY

SOMFY SUNEA CSI RTS Manuale utente

SOMFY

SOMFY Oximo io Manuale utente

SOMFY

SOMFY Oximo Series Istruzioni per il montaggio

SOMFY

SOMFY ILMO WT Manuale operativo

SOMFY

SOMFY Maestria 50 RTS Istruzioni operative

SOMFY

SOMFY LS 40 Manuale utente

SOMFY

SOMFY Altus RTS 120 V Istruzioni operative

SOMFY

SOMFY WireFree RTS Istruzioni operative

SOMFY

SOMFY Roll Up 28 RTS Manuale utente

SOMFY

SOMFY Tilt Only 50 WF RTS Manuale utente

SOMFY

SOMFY sonesse 30 rts Manuale di installazione

SOMFY

SOMFY Glydea ULTRA DIGITAL NETWORK Istruzioni operative

SOMFY

SOMFY Pergola io Istruzioni per il montaggio

SOMFY

SOMFY Maestria WT Manuale utente

SOMFY

SOMFY J4 RTS Istruzioni per il montaggio

SOMFY

SOMFY Sonesse ULTRA 30 WF Zigbee Li-ion Manuale utente

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente