Sony BVE-700 Manuale utente
EDITING CONTROL UNIT
BVE-700
INSTALLATION MANUAL
1st Edition
Serial No. 10001 and Higher
BVE-700
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
1 (E)
BVE-700
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 2 (E)
Related manuals................................................................................................... 2 (E)
Trademarks .......................................................................................................... 2 (E)
Installation
1-1. Operating Environment .........................................................................1-1 (E)
1-2. Power Supply ........................................................................................1-1 (E)
1-3. Installation Space ..................................................................................1-2 (E)
1-4. Matching Connectors and Cables..........................................................1-4 (E)
1-5. Input/Output Signals of Connectors......................................................1-5 (E)
1-6. Switch Settings on Boards and LED Description .................................1-8 (E)
1-7. Rack Mounting....................................................................................1-11 (E)
1-8. Installing the BKE-701 .......................................................................1-12 (E)
2 (E) BVE-700
Purpose of this manual This manual is the installation manual of Editing Control Unit BVE-700.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the BVE-700.
Related manuals Beside this Installation Manual, the following manuals are available for the unit.
..
..
.User’s Guide (Supplied with BVE-700)
This manual describes the application and operation of the unit.
..
..
.Operation Manual (Supplied with BVE-700)
This manual describes the overview, system connection examples, and specifica-
tions of the unit.
..
..
.BKE-701 Installation Manual (Supplied with BKE-701)
This manual describes the information related to the installation of the unit.
..
..
.BVE-700/BKE-701 Maintenance Manual (Available on request)
This manual describes the information that premise the service of BVE-700/BKE-
701 based on components replaced.
Trademarks Trademarks and registered trademarks used in this manual are follows.
.
Windows is a registered trademark of Microsoft Corporation.
.IBM is a registered trademark of International Business Machine, Inc.
.Ethernet is a registered trademark of Xerox Corporation.
Manual Structure
1-1 (E)
BVE-700
1-1. Operating Environment
Operating guaranteed temperature : +5 dC to +35 dC
Performnace guaranteed temperature : +10 dC to +30 dC
Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC
Mass : 10 kg
Prohibited locations
.Areas where the unit will be exposed to direct sunlight or
any other strong lights.
.Dusty areas
.Areas where it is subject to vibration.
.Areas with strong electric or magnetic fields.
.Areas near heat sources.
.Areas where is subjected to electricity noise.
.Areas where is subjected to static electricity noise.
Ventilation
The inside of the BVE-700 is cooled by a fan (rear and
sides).
The power supply can be damaged if the exhaust vent (rear
panel) and air intake (front panel) are blocked or the fan is
stopped.
Therefore, leave a blank space of more than 10 cm in the
front and back of the BVE-700.
1-2. Power Supply
1. Power specifications
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
Power requirements : AC 100 to 240 V ±10 %
50/60 Hz
Current consumption : Maximum 2.5 A
(with all optional boards installed)
n
As the inrush current at turn-on is the maximum 25 A (at
100 V/50 A (at 200 V), the capacity of the AC power must
be commensurate in it.
If the capacity of the AC power is not the adequately large,
the breaker of the AC power at the supply side will operate
or the unit will abnormally operate.
Installation
2. Recommended Power Cord
w
.The power cord is not supplied with the BVE-700. Be
sure to use the power cord that is applicable to places in
the area.
To avoid a fire or an electric shock, be sure to use the
designated power cord.
.Do not damage the power cord.
Otherwise, a fire or electric shock may result.
Required Parts for the U.S.A. and Canada
1Power cord : !1-551-812-11
Required Parts for Europe
1Power cord : !1-782-929-21
1
AC inlet
1
AC inlet
1-2 (E) BVE-700
1-3. Installation Space
Processor unit
26.5
520
440
465
57.2
375
482
61 380
17.5
132.4
Unit : mm
1-3. Installation Space
1-3 (E)
BVE-700
Control panel unit
Unit : mm
340
315.5
281
277.2
315
16.9
15
1-3. Installation Space
1-4 (E) BVE-700
1-4. Matching Connectors and Cables
Use the following connectors, cables, or equivalents when connecting cables to the unit.
Panel indication Connector name Matching connector and cable
Name Sony part No.
Processor unit
PLAYER-1 D-sub 9-pin, Female D-sub 9-pin, Male
PLAYER-2 Connector 9-pin, Male 1-560-651-00*1
PLAYER-3 Junction Shell 9-pin 1-561-749-00
RECORDER
MIXER
SWER
Processor unit
EDL D-sub 9-pin, Male D-sub 9-pin, Female
Connector 9-pin, Female 1-563-815-21
Junction Shell 9-pin 1-561-749-00
Processor unit
GPI D-sub 15-pin, Female D-sub 15-pin, Male
Connector 15-pin, Male 1-564-600-11*1
Junction Shell 15-pin 1-563-376-11
Processor unit
SDI INPUT BNC, 75 ZBNC, 75 Z
SDI OUTPUT 5C-FB coaxial cable*3
Processor unit
REF VIDEO BNC, 75 ZBNC, 75 Z
5C-2V coaxial cable*4
Processor unit/Control panel unit
PANEL D-sub 25-pin, Female D-sub 25-pin, Male
Connector 25-pin, Male 1-560-904-11*1
Junction Shell 25-pin 1-563-377-11
Processor unit
NETWORK RJ-45 modular jack*2__
*1 : To use plugs, the following crimp contacts are required.
AWG #18 to #22 : 1-566-493-21
AWG #22 to #24 : 1-564-774-11
AWG #24 to #30 : 1-564-775-11
*2 : Conforms to the IEEE 802.3 Ethernet 10BASE-T/100BASE-TX standards.
*3 : It is recommend to use the 5C-FB coaxial cable of Fujikura America Inc. or Fujikura Europe Ltd.
*4 : It is recommend to use the 5C-2V coaxial cable of Fujikura America Inc. or Fujikura Europe Ltd.
1-4. Matching Connectors and Cables
1-5 (E)
BVE-700
1-5. Input/Output Signals of Connectors
The input/output signals of the connectors at the rear panel
are as follows.
.Processor unit
PLAYER-1
PLAYER-2
PLAYER-3
RECORDER
MIXER
SWER : RS-422A (D-sub 9-pin, Female)
Pin No. Signal Function
1 GND Ground
2RX_Received data (_)
3TX+Transmitted data (+)
4 GND Ground
5_No Connection
6 GND Ground
7 RX+ Received data (+)
8TX_Transmitted data (_)
9_No Connection
EDL : RS-232C (D-sub 9-pin, Male)
Pin No. Signal Function
1_No Connection
2 RXD Received data
3 TXD Transmitted data
4_No Connection
5 GND Ground
6_No Connection
7 RTS (Not used at present)
8 CTS (Not used at present)
9_No Connection
_ EXT VIEW _
1
5
69
_ EXT VIEW _
5
1
96
GPI : D-sub 15-pin, Female
Pin No. Signal Function
1 GND Ground
2 OUT-1A Relay output-1A
3 OUT-2A Relay output-2A
4 OUT-3 (TTL) Open collector output-3
5 OUT-4 (TTL) Open collector output-4
6 IN-1 (TTL) Input-1
7 IN-3 (TTL) Input-3
8 GND Ground
9 OUT-1B Relay output-1B
10 OUT-2B Relay output-2B
11 _No Connection
12 _No Connection
13 GND Ground
14 IN-2 (TTL) Input-2
15 IN-4 (TTL) Input-4
EXT VIEW
1
8
9
15
1-5. Input/Output Signals of Connectors
1-6 (E) BVE-700
PANEL : D-sub 25-pin, Female
Pin No. Signal Function
1 GND Ground
2 12 V Panel Power Supply
3RX+Received data (+)
4 GND Ground
5TX_Transmitted data (_)
6 12 V Panel Power Supply
7 12 V Panel Power Supply
8_No Connection
9 GND Ground
10 GND Ground
11 GND Ground
12 GND Ground
13 GND Ground
14 12 V Panel Power Supply
15 12 V Panel Power Supply
16 RX_Received data (_)
17 GND Ground
18 TX+Transmitted data (+)
19 12 V Panel Power Supply
20 GND Ground
21 _No Connection
22 GND Ground
23 12 V Panel Power Supply
24 12 V Panel Power Supply
25 GND Ground
NETWORK : 10BASE-T/100BASE-TX (8-pin, Modular jack)
Pin No. Signal Function
1TX+Transmitted data (+)
2TX_Transmitted data (_)
3RX+Received data (+)
4_No Connection
5_No Connection
6RX_Received data (_)
7_No Connection
8_No Connection
1
13
14
25
EXT VIEW
18
_ EXT VIEW _
1-5. Input/Output Signals of Connectors
Altri manuali per BVE-700
2
Indice
Altri manuali Sony Unità di controllo
Sony
Sony HDCU3100 Manuale utente
Sony
Sony PVE-500 Manuale utente
Sony
Sony DNUR-SY3 Manuale utente
Sony
Sony CCP-6224 CCP-6324 MKS-8010B MKS-8011AMKS-8013A MKS-8014A MKS-8015A MKS-8017AMKS-8018A MKS-8019A MKS-8020A... Manuale utente
Sony
Sony CCP-8000 Series Manuale utente
Sony
Sony PWS-110PR1 Manuale utente
Sony
Sony BKNW-26 Manuale utente
Sony
Sony RM-B170 Manuale utente
Sony
Sony HDCU-1700 Manuale utente
Sony
Sony FCB-IX47 Manuale utente
Sony
Sony HDCU-950 Manuale utente
Sony
Sony BKM-15R Manuale utente
Sony
Sony PDBK-L1500 Manuale utente
Sony
Sony SX-M700 Manuale utente
Sony
Sony HSCU300RF Manuale utente
Sony
Sony HDCU2000 Manuale utente
Sony
Sony DSBK-180 Manuale utente
Sony
Sony IFU-WLM3 Manuale utente
Sony
Sony BKM-35H Manuale utente
Sony
Sony CCU-TX7P Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
