Spacerails Level 5 Manuale utente
LEVEL 5
PRODUCT AND CONSUMER WARNING
CHOKING HAZARD: This product contains small parts and is not intended for children under 3.
• This product is intended for users 8 years of age and older.
• To avoid choking, keep small parts away from children.
• Use caution – this product contains parts with sharp edges.
• To avoid potential damage to the product, only insert the included marbles into the elevator.
Page 2 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
FRONT
BACK
LEFT RIGHT
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 3
Keep parts together to avoid misplacing them.
ELEVATOR COMPONENTS
Arm Clip
x80
Arm Sheath
x80
Arm Holder A
x80
Arm Holder B
x85
Arm Lock
x165
Base
x12
Base Holder A
x6
Base Holder B
x4
PARTS INCLUDED
ARM COMPONENTSBASE COMPONENTS
Power Box
x1
Shaft (391mm)
x11
Elevator Helix
x16
Elevator Ring
x3
Elevator Cover
x1
Elevator Guard
x5
Power Box Stand
x1
Shaft (300mm)
x10
Shaft (200mm)
x2
Shaft Connector
(176mm) x1
Shaft Connector
(154mm) x3
Shaft Connector
(90mm) x2
SHAFT COMPONENTS SPLITTER COMPONENTS
ROTATION BLOCK COMPONENTS
Shaft (159mm)
x1
Shaft (65mm)
x1
Pendulum
x1
Marble Catch
x1
Counterweight
x1
START BLOCK COMPONENTS
Start Block
x1
Start Block
Cover x1
Wire Cutters or Utility Scissors
Pen or Marker
3 AA Batteries (newer models) or 1 C Battery
Ruler (in Centimeters)
REQUIRED TOOLS AND ITEMS NOT INCLUDED
Rail Splitter
x2
See-Saw Arm
x2
RAIL COMPONENTS
Pendulum Tray
x1
Steel Marble
x5
Rail Clip
x90
Rail Coupling
x10 Rail
Rail
34,000mm
Page 4 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
Step 1: Attach one Arm Holder A and one
ArmHolderB into one Arm Sheath. Insert one
Arm Clip into Arm Holder A.
Step 2: Insert Arm Lock through ArmHolderA
and Rail Clip. Carefully turn the Arm Lock
counter-clockwise to secure it in place.
PREPARE THE COASTER COMPONENTS
A
1
ARM ASSEMBLY QTY: 80
Arm Holder B
Arm Holder A
Arm Clip
Arm Sheath
Step 1: Cut two rails, each 55mm in length. Insert them
into the See-Saw Arm and the Rail Clip as shown above.
Step 2: Repeat for second See-Saw assembly.
BSEESAW ASSEMBLY QTY: 2
See-Saw
55mm Rails (2)
Rail Clip
Completed
See-Saw
assembly
Arm Holder B
Step 3: Attach one Arm Holder B into one Arm Sheath.
Insert the completed See-Saw assembly into the
ArmSheath.
Step 4: Repeat for second See-Saw assembly, installing
the Arm Holder B on the opposite side.
Note: The Arm Sheath
has two dierent holes:
Arm Holder B goes in
the squarish hole; all
other devices go in the
round hole.
Completed
See-Saw
assembly
Arm Sheath
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 5
CBASE ASSEMBLY
To avoid damaging parts, do not move or adjust parts while Arm Locks are engaged. To move the parts, release the
Arm Lock by turning clockwise, position the part as desired, then secure the Arm Lock again.
Step 1: Interlock Base block tabs as shown below.
Base Holder A
Base Holder B
Step 2: Press Base Holder A and Base Holder B pieces
into the Base blocks for a more secure hold.
Base Holder A
Base Holder B
Page 6 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
Step 3: Once the corkscrew is built,
attach three 391mm support shafts
to the Power Box.
DELEVATOR ASSEMBLY
Step 2: Connect 15 more Elevator
Helix pieces together with the male
part facing up to ll the shaft.
NOTE:
Install the rst Elevator
Helix piece male side
up and rotate it until
it slides in place and
engages with driver at
the base of Power Box.
Step 1: Place a 391mm Shaft
in the white hole on the
Power Box.
Step 4: Place the Elevator
Cover onto the top of the
elevator assembly.
Step 6: Place the
three Elevator Rings
over the three shafts.
Step 5: Connect Rail Clips to
each Elevator Ring as shown.
(Note that the middle ring
only gets two Rail Clips.)
Install Elevator Rings with tabs
facing up, as shown above.
Entry 1
Entry 2
Entry 3
Entry 4
Entry 5
Exit 1 Exit 2
Exit 3
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 7
ROTATION ASSEMBLY
F
300mm Shaft
Arm Holder B
Arm
Lock
Arm Lock
Arm Holder B
Counterweight
Arm Lock
Rotation Gear
Marble Catcher
159mm Shaft
65mm Shaft
Step 1: Assemble
parts as illustrated.
Counterweight: If the rotation
is not functioning properly,
adjust the position of the
Counterweight until it does so.
ERAIL SPLITTER
Prepare Rail Splitter:
Attach one Rail Clip to each
of the Rail Splitter posts.
Step 8: Attach Power Box to
the Power Box Stand.
Insert into
holes on base
Power Box
Power Box Stand
Step 7: Attach
an Elevator
Guard to each
of the Elevator
Rings, then to
the right side of
the Rail Clip.
NOTE:
The Marble may fall out of the
elevator if it enters too fast.
Page 8 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
GSTART BLOCK ASSEMBLY
Step 1: Assemble parts as illustrated.
Step 2: Snap the Start Block Cover
on the Start Engine as shown.
Step 3: When positioning the Start Block on the
300mm Shafts, tilt the right (narrower) side up
slightly to encourage smoother operation.
300mm Shaft Rail Clip
Start Block
Start Block Cover
Arm Holder B
Arm Holder B
Rail Clip
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 9
FRONT BACK
Rotation
Assembly Start Block
Assembly
Elevator
Assembly
Shaft Connector
(90mm)
Shaft Connector
(154mm)
Shaft Connector
(176mm)
D
B
A
C
E
H
G F
IJ
KL
M
N
OP
Q
R
S
CONSTRUCTING THE COASTER
AINSTALL THE COASTER
SHAFTS, ROTATION ASSEMBLY
AND ELEVATOR
2
Page 10 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
Illustration of shafts are 1:64, or approximately 60% of scale
NOTE:
Arm Holder B
Arm Assembly
See-Saw Assembly (back)
See-Saw Assembly (front)
Each rail connection to the Arm Clips is
labeled according to their shaft letter and
placement on the shaft from the bottom up.
Shaft (391mm)
Shaft (300mm)
19mm
29mm
35mm
41mm
43mm
55mm
75mm
99mm
127mm
150mm
244mm 246mm
248mm
289mm
296mm
318mm
322mm
361mm
372mm
DB
AC E
A-1
A-2
B-1
B-2
B-3
C-1
C-2
D-1
D-2
D-3
D-4
E-1
E-2
E-3
D-5
D-6
E-4
E-5
E-6
BSHAFT ASSEMBLY
FRONTBACK
BOTTOM
TOP
Shaft
letter
Order placement
from bottom
A-1
35mm
Placement
on shaft
Indice
Altri manuali Spacerails Giocattolo
Spacerails
Spacerails LEVEL 6 Manuale utente
Spacerails
Spacerails Level 1 Manuale utente
Spacerails
Spacerails Level 3 Manuale utente
Spacerails
Spacerails Level 8 Manuale utente
Spacerails
Spacerails Level 9 Manuale utente
Spacerails
Spacerails LEVEL 4 Manuale utente
Spacerails
Spacerails Level 7 Manuale utente
Spacerails
Spacerails Level 2 Manuale utente
