Spacerails Level 9 Manuale utente
LEVEL 9
PRODUCT AND CONSUMER WARNING
CHOKING HAZARD: This product contains small parts and is not intended for children under 3.
• This product is intended for users 8 years of age and older.
• To avoid choking, keep small parts away from children.
• Use caution—this product contains parts with sharp edges.
• To avoid potential damage to the product, only insert the included marbles into the elevator.
Page 2 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
PARTS INCLUDED
RECOMMENDED ITEMS (NOT INCLUDED)
Wire Cutters or Utility Scissors
Pen or Marker
6 AA Batteries (newer models) or 2 C Batteries
Ruler (in Centimeters)
ELEVATOR COMPONENTS
Power Box
x 2
Elevator Helix
x 38
Elevator Ring
x 9
Elevator Cover
x 4
Elevator Guard
x 11
Power Box Stand
x 2
Shaft Clip
x 1
Pendulum
x 1
Marble Catch
x 1
Counterweight
x 1
Pendulum Tray
x 1
Rail Splitter
x 3
STUNT COMPONENTS
SHAFT COMPONENTS
600mm
x 9
391mm
x 8
300mm
x 20
200mm
x 7
159mm
x 19
65mm
x 8
Shaft Cap
x 2
ARM COMPONENTS
Arm Clip
x 147
Arm Sheath
x 168
Arm Holder A
x108
Arm Holder B
x 265
Arm Lock
x 375
See-Saw Arm
x 2
Rail Coupling
x 15
Rail
76,000 mm
Rail Clip
x 300
Marble
x 12
RAIL COMPONENTS
BASE COMPONENTS
Base
x 13
Double Sided Base
x 1
Base Holder A
x 13
Base Holder B
x 10
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 3
1PREPARE ARMS
Attach one Arm Holder B on each side
of the Arm Sheath.
Attach one Arm Holder B on each side
of the Arm Sheath. When assembling
shafts F, BC, and BD, slide one
ArmHolder B on shaft and insert one
ArmClip and add the Arm Lock.
BARM B QTY: 56
ARM D QTY: 3
AARM A QTY: 107
Slide Arm Holder B onto
shaft. Insert Arm Lock
through ArmHolder B and
Rail Clip. Turn the Arm Lock
counter-clockwise to secure
the Rail Clip in place. These will
be assembled during the shaft
assembly step to shafts D, E, F,
G, BC and BD.
ARM C QTY: 36
Step 1: Attach one Arm Holder A and one
Arm Holder B with one Arm Sheath. Insert
one Arm Clip into Arm Holder A.
Step 3: Turn the Arm Lock
counter-clockwise to secure
the Arm Clip in place.
Step 2: Insert Arm Lock through
Arm Holder A and Arm Clip.
To avoid damaging parts, do not move or adjust the Rail Clip while locked in the arm. To move the Rail Clip, release
Arm Lock by turning clockwise, position Rail Clip as desired, then secure Arm Lock again.
C
D
Cut two 7.5 cm lengths of rail and insert
into See-Saw as shown using a Rail Clip
to support the ends of the rail.
Attach Arm Holder B to the square receiver side of Arm Sheath
to create the arm. Attach the arm to the shaft and the shaft
to the base prior to attaching the round receiver side of the
ArmSheath to the See-Saw Arm.
SEE-SAW ARM QTY: 1 LEFT & 1 RIGHT
Page 4 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
Step 1: Interlock all
Base block tabs as
shown above.
Step 2: Press Base Holder A and
Base Holder B pieces into the Base
blocks for a more secure hold.
NOTE:
Please see the included
full size drawings for the
next several steps. This will
simplify the positioning of
base, arms, shafts, and the
rail cut lengths.
Step 3: Assemble base blocks as shown in the
Illustration of completed base with all tabs
locked and Base Holders installed. Approximately
20% of actual size.
BASE ORIENTATION
BACK OF BASE
FRONT OF BASE
LEFT
OF BASE
RIGHT
OF BASE
2BASE ASSEMBLY
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 5
ELEVATOR A
Step 3: Once the corkscrew
is built, attach three 300 mm
support shafts to the Power Box.
Step 1: Place a 300 mm shaft in
the white hole on the Power Box.
Step 2: Connect Elevator Helix
pieces together with the male part
facing up to ll the shaft.
NOTE:
Install the rst Elevator
Helix piece male side
up and rotate it until
it slides in place and
engages with driver at
the base of Power Box.
Step 6: Attach Rail Clips to
each Elevator Ring as shown.
Step 4: Slide each Elevator Ring
into position on the support
shafts right-side up.
Step 5: Place the Elevator
Cover onto the top of the
elevator assembly.
NOTE:
Elevator Rings are
right side up when
tabs in red are on
the top.
240 mm
40 mm
0 mm
3ELEVATOR ASSEMBLY
Page 6 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
ELEVATOR B
Step 3: Once the corkscrew
is built, attach three 391 mm
support shafts to the Power Box.
Step 1: Place a 391 mm shaft in
the white hole on the Power Box.
Step 2: Connect Elevator Helix
pieces together with the male part
facing up to ll the shaft.
NOTE:
Install the rst Elevator
Helix piece male side
up and rotate it until
it slides in place and
engages with driver at
the base of Power Box.
Step 6: Attach Rail Clips to
each Elevator Ring as shown.
Step 5: Place the Elevator Cover
onto the top of the elevator
assembly.
Step 4: Slide each Elevator Ring
into position on the support
shafts right-side up.
335 mm
30 mm
0 mm
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 7
ELEVATOR C
Step 3: Once the
corkscrew is built,
attach three 300 mm
support shafts to the
Elevator Cover.
Step 1: Insert a 300 mm
shaft rst into a Shaft Cap
and then into the center
hole of an Elevator Cover.
Add the Shaft Clip 2 cm up
from the base.
Step 2: Connect
Elevator Helix pieces
together with the
male part facing up
to ll the shaft.
Step 6: Attach Rail
Clips to each Elevator
Ring as shown.
Step 5: Place the Elevator
Cover onto the top of the
elevator assembly.
2 cm
Step 4: Slide each
Elevator Ring into
position on the
support shafts
right-side up.
NOTE:
The Marble may
fall out of the
elevator if it
enters too fast.
Add Elevator Guards to the right of each
Rail Clip installed to the bottom two
Elevator Rings.
ADDING GUARDS: Repeat this step for all
three elevators that have been built.
75 mm
185 mm
0 mm
Page 8 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
4PREPARE PENDULUM STUNT
Attach the Marble Catch to a 200 mm shaft. Insert
other end of shaft to the left side of the Pendulum.
Next attach an Arm Holder B to a 65 mm shaft with
an Arm Lock and add the Counterweight to the post
of Arm Holder B. Finally, attach the 65 mm shaft to
the right hand side of the Pendulum.
NOTE:
The Counterweight is adjustable, if the
pendulum stunt is not working, try
moving the weight to dierent positions.
NOTE:
The shafts listed below contain no arms and are not included in the drawings.
Shafts: I, J, L, M, N, O, W, X, Y, Z, AX, AY, and AZ
Step 1: Slide Arm Holder B of each arm on to a shaft and lock in
place with Arm Lock. Refer to the next pages for orientation and
location of each arm.
Step 2: Attach each arm as shown in step 1 with the orientation
and location shown on the following pages. In later steps the letter
of each shaft and number of each arm will guide in the installation
of the rails. For example Arm A-3 is 104 mm from the base.
Shaft illustrations are approximately 37% of actual size. All shaft
measurements are in Millimeters.
Arm A
Arm B
Arm C
Arm D
See-Saw Arm
ARM TYPE REFERENCE
5SHAFT ASSEMBLY
Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com Page 9
Shaft A Shaft C Shaft D Shaft F
10
600
44
54
104
168
185
242
267
315
335
448
500
563
578
310
355
Shaft B
600
44
54
185
340
524
595
300
46
100
129
158
187
216
245
286
Shaft E
300
46
112
141
170
198
228
257
286
300
100
40
130
160
190
224
291
10
Shaft G
300
105
135
165
195
225
291
285
TOP
BASE
FRONT
OF BASE
BACK
OF BASE
SHAFT TO BASE ORIENTATION
Page 10 Seaich Corporation, LLC. All rights reserved. www.seaich.com |Spacerails, LLC. www.spacerails.com
Shaft H
44
54
186
200
Shaft K
44
55
95
186
168
200
Shaft P
50
173
200
Shaft Q
105
155
200
TOP
BASE
FRONT
OF BASE
BACK
OF BASE
SHAFT TO BASE ORIENTATION
Shaft R Shaft S
600 600
194
217 222
278 284
357
436
480
490
558 550
Shaft T
Shaft U
300
3
3
17
18
36
46
78
88
119
131
163
172
214
279
290
300
278
255
295
Indice
Altri manuali Spacerails Giocattolo
Spacerails
Spacerails Level 2 Manuale utente
Spacerails
Spacerails LEVEL 6 Manuale utente
Spacerails
Spacerails Level 8 Manuale utente
Spacerails
Spacerails LEVEL 4 Manuale utente
Spacerails
Spacerails Level 1 Manuale utente
Spacerails
Spacerails Level 3 Manuale utente
Spacerails
Spacerails Level 5 Manuale utente
Spacerails
Spacerails Level 7 Manuale utente
