Spectra Precision Trimble UL 633N Guida all'installazione
UL633N
Hands-On training
11.07.17
UL633N Components
a
b
c
e
d
f
i
g
h
l
j
k
i
a - Keypad/LCD-Display
b - Handle
c - Rotor with fan beam lens
d - Sunshade
e - Axes Alignment Marks
f - Sighting Guides/Scope Mounts
g - Battery door
h - Rubber Cover/Recharge Jack
i - 5/8” x 11 Tripod Mounts
j - Rubber Feet
k -Turnable Legs
l - Plus and Minus Battery
Diagrams
Powering the UL633N
1 –UL is shipped with a rechargeable NiMH
battery pack (Q104667), alkaline batteries
can be used as a backup.
2 –The rechargeable battery pack can be
charged inside as well as outside of the
unit
3 –The charger (Q104781) can be used as a
power supply when used Indoors
4 –Alkaline batteries can be used as a backup
5 –An external power cable (Q104802) can be
used
6 –Plus and minus symbols indicate
how to put the alkalines into the
battery compartment
Powering the RC603N
1. Open the battery door using a coin or similar pry
device to release the battery door tab on the RC603N.
RC603N will be shipped with alkaline batteries.
Rechargeable batteries can be used optional but need
to be charged externally
2. Insert two AA batteries noting the plus (+) and minus (-)
diagrams inside the battery housing.
3. Close the battery door. Push down until it “clicks”
into the locked position.
Battery status laser Battery Status Remote Control
Mask selection Status Radio Connectivity
Rotation speed/Scan angle
HI alert function is activated
Fan Beam is activated
Standard Display
The remote control mirrors the functionality of the UL keypad.
Button 1: Quickly press and release starts
the MENU entry.
Button 2: Quickly press and release starts
the grade entering mode.
Button 3: Quickly press and release
activates/deactivates the manual mode.
Button 4: Quickly press and release to
toggle through the pre-selected rotation
speeds.
Press and hold for three seconds changes
the unit into scan mode. When in scan mode,
quickly press and release button 4 toggles
through the pre-selected scan sizes.
Button 5, 8: up/down arrow buttons.
Button 6, 7: left/right arrow buttons.
Button 9:ON/OFF button - press for 1
second to turn on the unit; press and hold for
2 seconds to turn off the unit.
Leveling/Standby –LED (green/red)
Turning On/Off the laser
Press the power button to turn On/Off the laser.
–Depending on the setup (horizontal or vertical) and if a grade value has been dialed in, the
unit starts the temperature/reference check while the thermometer symbol is flashing.
–If there occur additional vibrations at the jobsite during the
reference check, the leveling time can be increased.
When the temperature/reference check has been finished, the standard display appears and the
bubble symbols flash until self-leveling has been completed.
Don’t start a menu function before the reference check has been finished.
If the self-leveling can’t be finished based on the selected sensitivity, an error message appears
Abubble symbol helps to adjust the unit at the cross axis when
set up vertical for automatic Spot Align or in vertical manual mode.
Turning On/Off the Laser
X-Y-Z-grade entering
Step and Go mode
Quickly press and release button 2starts the grade entering mode.
Both grade values will be shown.
Press/release button 1grade reverse Y
Press/release button 2grade reverse X
Press/release button 3return to the standard display.
Quickly press and release button 4to confirm the selected grade
value and return to the standard display
Press and hold button 6 or 7 (left/right) to change X- axis grade value
after the comma; press and hold buttons 6 + 7 simultaneously starts X-axis quick change mode
where the grade value in front of the comma will be set to 0% and then starts changing in 1%
increments.
Press and hold button 5 or 8 (up/down) for changing Y/Z -axis grade value; press and hold buttons 5
+ 8 simultaneously starts Y/Z - axis quick change mode where the grade value in front of the comma
will be set to 0% and then starts changing in 1% increments
Note: When the grade value for either axis reaches its highest amount, the grade value switches to the
lowest value for that axis. For example, the value switches from +25%to -25%.
The laser will self-level to the required grade position after confirming the grade change with button 4.
Note: The bubble symbols at the laser’s LCD will flash until the laser has been
self-leveled to the requested grade position.
Standard Display
Standard Features
X-Y-Z-grade entering
Digit Select mode
Quickly press and release button 2 starts the grade entering mode.
Both grade values will be shown.
Press/release button 1quick set to 0%
Press/release button 2change the sign of the grade value
Press/release button 3return to the standard display.
Quickly press and release button 4to confirm the selected grade value
and return to the standard display
Press and release button 5 or 8(down or up) to move the cursor to
the X- or Y-axis (not used in Z- mode).
Pressing and releasing button 6 or 7 (right or left) moves the cursor
to the right/left.
Use button 1 or 2(Plus or Minus) to set the desired digit.
The laser will self-level to the required grade position after confirming
the grade change with button 4.
Note: The bubble symbols at the laser’s LCD will flash until the laser has been self-leveled to the requested
grade position.
Standard Display
Standard Features
Using the Rotation mode
Repeatedly pressing the button 4 toggles through 0, 80,200,600,750 rpm regardless if the unit is in
automatic or manual mode. At 0 rpm, the beam stops automatically close to the +Y- axis center position.
In automatic mode, using buttons 5/8 increases/decreases rotor speed from 0 to 80 and then up to 750 rpm
continuously in 10 rpm increments.
Pointing mode
At 0 rpm, buttons 6/7 move the beam to the left/right side. When set up vertically at 0 rpm, button 5/8 move the
beam clockwise/counterclockwise.
Note: Press and hold button 4 for three seconds to change the unit from rotation mode (default) into scan mode.
Using the Scan mode
Press and hold button 4 at the Standard Display for three seconds to change the unit into scan mode.
Quickly press and release button 4 to toggle between the pre-selected scan sizes 5, 15,45,90,180 degrees
and 0; regardless if the unit is in automatic or manual mode.
When working in horizontal automatic mode, press and hold button 5/8 to increase/decrease the line size
in 5 degrees increments. Press and hold button 6/7 moves the scan line to the right/left direction.
When used in automatic vertical mode, pressing and holding button 5/8 moves the scan line
counterclockwise/clockwise.
When set up vertical, pressing and holding button 6/7 moves the scan line into the right/left direction
regardless if in automatic or manual mode.
Note: Press and hold button 4 for three seconds to change the unit back to rotation
mode (default) mode.
Standard Features
Manual mode
Pressing and releasing button 3 at the Standard Display activates/deactivates the manual mode
regardless if set up horizontal or vertical.
Manual mode is indicated by horizontal lines next to the axes symbols. An additional bubble helps to adjust
the laser on the cross axis when set up vertical.
In Manual mode (horizontal), the Y-axis can be sloped by pressing the Up-(5) and Down-(8)- Arrow
buttons on the laser‘s keypad or the remote control. Additionally, the X-axis can be sloped by pressing
the Left-(6) and Right-(7) Arrow-buttons on the laser or remote control.
In vertical mode, the up and down arrow buttons adjust the Z-axis slope, and the left and right arrow
buttons align the laser beam to the right/left side.
To resume automatic self-leveling mode, press the manual button 3 again.
Standard Features
Altri manuali per Trimble UL 633N
1
Indice
Altri manuali Spectra Precision Livello laser
Spectra Precision
Spectra Precision LL100N Istruzioni per il montaggio
Spectra Precision
Spectra Precision LL300S Manuale di istruzioni
Spectra Precision
Spectra Precision LL300S Manuale utente
Spectra Precision
Spectra Precision 1452GC Manuale utente
Spectra Precision
Spectra Precision LL300 Manuale utente
Spectra Precision
Spectra Precision LL300S Manuale utente
Spectra Precision
Spectra Precision GL6X2N Guida all'installazione
Spectra Precision
Spectra Precision HV302 Manuale utente
Spectra Precision
Spectra Precision LL300S Guida all'installazione
Spectra Precision
Spectra Precision AL28M Manuale utente
