Staco Energy UNISTAR SB-NET Manuale utente

003-2594 REV B

UNISTAR SB-NET

120-230V 50/60Hz

800VA to 3kVA

USER MANUAL

Page | ii

No reproduction of any part of this manual, even partial, is permitted without the authorization of Staco

Energy Products Company. The Staco Energy Products Company reserves the right to modify the

product described herein, in order to improve it, at any time and without notice.

301 Gaddis Boulevard • Dayton, Ohio 45403

U.S. Toll Free 866-261-1191

(937) 253-1191 • Fax: (937) 253-1723

Web site: www.stacoenergy.com

Thank you for choosing our product.

Staco Energy is highly specialized in the development and production of uninterruptible power

systems (UPS). The UPS’s of this series are high quality products, carefully designed and

manufactured to ensure optimum performance.

Page | iii

Table of Contents

1. Important Safety Warnings................................................................................................................... 1

1.1 Transportation ................................................................................................................................ 1

1.2 Preparation..................................................................................................................................... 1

1.3 Installation...................................................................................................................................... 1

1.4 Operation ....................................................................................................................................... 1

1.5 Maintenance, Service and Faults.................................................................................................... 2

1.6 WEEE............................................................................................................................................. 3

1.7 FCC (120V Models)........................................................................................................................ 3

1.8 EMC (230V Models) ....................................................................................................................... 3

2. Installation and setup ........................................................................................................................... 4

2.1 120V Models Rear panel view........................................................................................................ 4

2.1.1 800VA/1.1KVA/1.5KVA............................................................................................................. 4

2.1.2 2 kVA....................................................................................................................................... 4

2.1.3 3 kVA....................................................................................................................................... 4

2.2 230V Models Rear panel view........................................................................................................ 5

2.2.1 800VA/1.1KVA/1.5KVA............................................................................................................. 5

2.2.2 2 kVA....................................................................................................................................... 5

2.2.3 3 kVA....................................................................................................................................... 5

2.3 Operating principle ......................................................................................................................... 6

2.4 Install the UPS................................................................................................................................ 6

2.4.1 Rack-mount Installation ........................................................................................................... 7

2.4.2 Tower Installation..................................................................................................................... 7

2.5 Setup the UPS................................................................................................................................ 8

2.6 Battery Replacement.................................................................................................................... 10

2.7 Battery Kit Assembly (option).........................................................................................................11

3. Operation ........................................................................................................................................... 13

3.1 Button operation........................................................................................................................... 13

3.2 LCD Panel.................................................................................................................................... 14

3.3 Audible Alarm ............................................................................................................................... 15

3.4 LCD display wordings index ......................................................................................................... 15

3.5 UPS Settings................................................................................................................................ 16

3.6 Steps for setting programmable outlet.......................................................................................... 18

3.7 Operating Mode Description......................................................................................................... 19

3.8 Faults Reference Code................................................................................................................. 20

3.9 Warning indicator.......................................................................................................................... 20

4. Troubleshooting.................................................................................................................................. 21

5. Storage and Maintenance .................................................................................................................. 22

5.1 Operation ..................................................................................................................................... 22

5.2 Storage......................................................................................................................................... 22

6. UPS Specifications............................................................................................................................. 23

6.1 120V Models .................................................................................................................................... 23

6.2 230V Models .................................................................................................................................... 24

Page | 1

1. Important Safety Warnings

Please complywith all warnings and operating instructions inthis manual strictly. Save this manual properly

and read carefullythe following instructions before installing the unit. Do not operate this unit before reading

through all safety information and operating instructions carefully

1.1 Transportation

Please transport the UPS system only in the original package to protect against shock and impact.

1.2 Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environment. The UPS

system must be absolutely dry before being installed. Please allow at least two hours for the UPS

system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or near heater.

Do not block ventilation holes in the UPS housing.

1.3 Installation

Do not connect appliances or devices which would overload the UPS system (e.g. laser printers) to the

UPS output sockets.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UPS output sockets.

The UPS can be operated by any individuals with no previous experience.

Connect the UPS system only to an earthed shockproof outlet which must be easily accessible and

close to the UPS system.

Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your computer) to

connect the UPS system to the building wiring outlet (shockproof outlet).

Please use only VDE-tested, CE-marked power cables to connect the loads to the UPS system.

When installing the equipment, it should ensure that the sum of the leakage current of the UPS and the

connected devices does not exceed 3.5mA.

Temperature Rating - Units are considered acceptable for use in a maximum ambient of 40°C (104°F).

For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be

easily accessible.

CAUTION: The unit is heavy. Lifting the unit requires a minimum of two people.

Check if there is a protection device against over current and short circuit in the upstream of the UPS

system. The recommended protection spec is 11A for 800VA~1100VA, 15A for1.5KVA, 20A for LV

2KVA and 30A for 2.5~3KVA with a B or C trip curve.

1.4 Operation

Do not disconnect the mains cable on the UPS system or the building wiring outlet (shockproof socket

outlet) during operations since this would cancel the protective earthing of the UPS system and of all

connected loads.

The UPS system features its own, internal current source (batteries). The UPS output sockets or output

terminals block may be electrically live even if the UPS system is not connected to the building wiring

outlet.

In order to fully disconnect the UPS system, first press the OFF/Enter button to disconnect the mains.

Prevent no fluids or other foreign objects from inside of the UPS system.

The EPO, RS-232 and USB circuits are an IEC 60950-1 safety extra low voltage (SELV) circuit. This

circuit must be separated from any hazardous voltage circuits by reinforced insulation.

Page | 2

1.5 Maintenance, Service and Faults

The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified

maintenance personnel.

Caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring

outlet), components inside the UPS system are still connected to the battery and electrically live and

dangerous.

Before carrying out any kind of service and/or maintenance, disconnect the batteries and verify that no

current is present and no hazardous voltage exists in the terminals of high capability capacitor such as

BUS-capacitors.

To avoid electrical shock, turn off the unit and unplug it form the AC power source before servicing the

battery

Only persons who are adequately familiar with batteries and with the required precautionary measures

may replace batteries and supervise operations. Unauthorized persons must be kept well away from

the batteries.

Caution - risk of electric shock. The battery circuit is not isolated from the input voltage. Hazardous

voltages may occur between the battery terminals and the ground. Before touching, please verify that

no voltage is present!

Batteries may cause electric shock and have a high short-circuit current. Please take the precautionary

measures specified below and any other measures necessary when working with batteries:

－remove wristwatches, rings and other metal objects

－use only tools with insulated grips and handles.

When changing batteries, install the same number and same type of batteries.

Do not attempt to dispose of batteries by burning them. This could cause battery explosion.

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and eyes. It may be

toxic.

When replacing batteries, use the same type and number of batteries or battery packs.

Manufacture

Type

Rated

Toplite (Guangzhou) Technology

Battery Co Ltd (MH29104)

NPW45-12

12 V dc, 9.0 Ah

UXW460-12

12 V dc, 9.0 Ah

NPW36-12

12 V dc, 7.2 Ah

UXW360-12

12 V dc, 7.2 Ah

NPW45-12 FR

12 V dc, 7.0 Ah

UXW460-12/FR

12 V dc, 7.0 Ah

NPW36-12 FR

12 V dc, 7.0 Ah

UXW360-12/FR

12 V dc, 7.0 Ah

CSB Battery Co Ltd (MH14533)

UPS 12460 F2

12 V dc, 9.0 Ah

UPS 12360 6

12 V dc, 6.5 Ah

UPS 12360 7

12 V dc, 6.5 Ah

HR 1234W

12 V dc, 8.5 Ah

HR 1234W FR

12 V dc, 8.5 Ah

Yuasa Battery (Guangdong) Co

Ltd (MH29616)

NPW45-12

12 V dc, 8.0 Ah

NPW45-12FR

12 V dc, 8.0 Ah

Page | 3

Do not dismantle the UPS system.

A battery can may cause a risk of electrical shock and high short-circuit current. The

following precautions should be observed when working on batteries:

a) Remove watches, rings, or other metal objects.

b) Use tools with insulated handles.

c) Wear rubber gloves and boots.

d) Do not lay tools or metal parts on top of batteries.

e) Disconnect charging source prior to connecting or disconnecting batteryterminals.

f) Determine if battery is inadvertently grounded. If inadvertently grounded,remove source

from ground. Contact with any part of a grounded battery can resultin electrical shock.

The likelihood of such shock can be reduced if such groundsare removed during

installation and maintenance.

1.6 WEEE

Information for Protection of the Equipment

UPS SERVICING –This UPS and batteries makes use of components dangerous for the enviroment

(electronic cards, electronic components). The components removed must be taken to specialized

collection and disposal centers.

Notice to European Union Customers: Disposal of Old Appliances –This product has been

supplied rom an enviromentally aware manufacturer that complies with Waste Electrical and Electrnic

Equipment (WEEE) Directive 2002/96/CE. The ”crossed-out wheelie bin” symbol at right is placed on this

product to encourage you to recycle wherever possible. Please be environmentally responsible and

recycle this product through your recycling facility at its end of life. Do not dispose of this product as

unsorted municipal waste. Follow locla municipal waste ordinances for proper disposal provisions to

reduce the environmental impact to waste ectrical and electronic equipment (WEEE)

1.7 FCC (120V Models)

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

1.8 EMC (230V Models)

WARNING: This is a category C2 UPS product. In a residential environment, this product may cause

radio interference, in which case the user may be required to take additional measures.

Page | 4

2. Installation and setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.

Please keep the original package in a safe place for future use.

2.1 120V Models Rear panel view

2.1.1 800VA/1.1KVA/1.5KVA

2.1.2 2 kVA

2.1.3 3 kVA

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Network/Fax/Modem surge protection

5. Emergency power off function connector (EPO)

6. USB communication port

7. RS-232 communication port

8. SNMP intelligent slot

9. External battery connector

kVA

Input

Connection

Output

Connection

800VA/1.1KVA/1.5KVA

5-15P

5-15R

2kVA

5-20P

5-20R

3 kVA

L5-30P

5-20R & L5-30R

Table 1 –Input/Output Connections

Page | 5

2.2 230V Models Rear panel view

2.2.1 800VA/1.1KVA/1.5KVA

2.2.2 2 kVA

2.2.3 3 kVA

1. Programmable outlets: connect to non-critical loads.

2.Output receptacles: connect to mission-critical loads.

3.AC input

4.Network/Fax/Modem surge protection

5.Emergency power off function connector (EPO)

6.USB communication port

7.RS-232 communication port

8.SNMP intelligent slot

9.External battery connector

kVA

UPS Input

Connection

UPS Output

Connection

Input Cord

Connector

800VA/1.1KVA/1.5KVA

IEC320-C14

IEC320-C13

C13

2kVA

IEC320-C20

IEC320-C13

C19

3kVA

IEC320-C20

IEC320-C13 & IEC320-C19

C19

Table 2 –Input/Output Connections

Page | 6

2.3 Operating principle

EMI/RFI

Filters

Battery

Charger Battery

DC-to-DC

Converter

Inverter

AVR

Output

The UPS is composed of mains input, EMI/RFI Filters, Inverter, Battery charger, DC-to-DC converter,

battery, AVR TX and UPS output

2.4 Install the UPS

For safety consideration, the UPS is shipped out from factory without connecting battery wires. Before

installing the UPS, please follow the below steps to re-connect battery wire.

Step 1 Step 2 Step 3

Step 1: Remove front panel.

Step 2: Remove battery panel and re-connect battery wire.

Step 3: Put battery panel and cover back to the unit.

This UPS can be either displayed on the desk or mounted in the 19” rack chassis. Please choose proper

installation to position this UPS.

Page | 7

2.4.1 Rack-mount Installation

CAUTION –Do NOT use the mounting brackets to lift the unit. The mounting brackets are only for securing

the unit to the rack.

Install UPS alone

Install UPS and external battery

2.4.2 Tower Installation

Install UPS alone

Install UPS and external battery

NOTE: When installing the UPS or battery pack with feet, keep 2.76in distance from the edge of the unit.

Indice

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente