StarTech.com SAT32M225 Manuale utente

User Manual of Product 1:

StarTech.com USB 3.1 (10Gbps) Hard Drive Duplicator Dock

for 2.5" & 3.5" SATA SSD HDD + 4Kn - USB/ USB-C

Thunderbolt 3 Compatible Cloner (SDOCK2U313R)

User Manual of Product 2:

StarTech.com M.2 SSD to 2.5in SATA Adapter Converter with

Open Frame Housing and 7mm Height (SAT32M225), Green

Manual Revision: 10/23/2015

For the latest information, technical specications, and support for

this product, please visit www.startech.com/SDOCK2U313R.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

SDOCK2U313R

USB 3.1 (10Gbps) Standalone Duplicator

Dock for 2.5” and 3.5” SATA Drives

*actual product may vary from photos

Quick start guide

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Quick start guide

Table of Contents

Introduction............................................................................................1

Packaging contents.................................................................................................................................. 1

System requirements............................................................................................................................... 1

Product diagram ....................................................................................2

Front view .................................................................................................................................................... 2

Rear view...................................................................................................................................................... 3

Installation ..............................................................................................4

Connect the duplicator dock................................................................................................................ 4

Install a drive............................................................................................................................................... 4

Prepare a drive for use............................................................................................................................. 4

Using the duplicator dock ....................................................................6

Duplicate a drive ....................................................................................................................................... 6

Remove a drive from your computer................................................................................................. 6

About the LED indicators......................................................................7

Technical support...................................................................................8

Warranty information............................................................................8

Quick start guide

Introduction

Packaging contents

• 1 x USB 3.1 duplicator docking station

• 1 x universal power adapter (NA/EU/UK/AU)

• 1 x USB C to B cable

• 1 x USB A to B cable

• 1 x quick start guide

System requirements

• Computer system with a USB port

• Up to two 2.5 in. or 3.5 in. SATA hard drives (HDD) or solid-state drives (SSD)

The SDOCK2U313R is OS independent and doesn’t require any additional drivers or

software.

Note: To obtain the maximum USB throughput, you must use a computer with a USB

3.1 Gen 2 (10Gbps) port.

System requirements are subject to change. For the latest requirements, please visit

www.startech.com/SDOCK2U313R.

Quick start guide

Product diagram

Front view

Drive eject

buttons

POWER button

and LED

PC/COPY mode button

and LED

START duplication button

Drive LEDs

Duplication

progress LED

Drive #1 slot (destination for

duplication)

Drive #2 slot (source for

duplication)

Quick start guide

Rear view

USB 3.1 Gen 2 port Power adapter port

Quick start guide

Installation

Connect the duplicator dock

Warning! Drives and storage enclosures should be handled carefully, especially when

they’re transported. If you’re not careful with your drives, you may lose data as a result.

Always handle storage devices with caution.

1. Connect the external power adapter from the duplicator dock to a power outlet.

2. Connect one of the included USB 3.1 cables from the duplicator dock to a USB port

on your computer system. Your computer can either be turned on or turned o

when you connect the USB cable.

3. Press the POWER button on the top of the duplicator dock. The LED indicators

should light up to indicate that the dock is turned on.

Install a drive

1. Carefully align a 2.5 in. or 3.5 in. SATA drive with a drive slot on the duplicator dock,

so that the SATA power and data connectors on the drive are aligned with the

corresponding connectors that are inside of the drive slot.

2. Insert the 2.5 in. or 3.5 in. SATA drive into one of the drive slots.

Note: If you’re connecting drives for duplication, place the drive containing the data

that you intend to copy from in the drive #2 slot, and place the drive that you intend to

copy the data to in the drive #1 slot.

3. Press the POWER button to turn on the duplicator dock.

After the drive is installed and the duplicator dock is turned on, your computer

automatically recognizes the drive and it’s accessible as though the drive is installed

internally in the system. If your computer doesn’t automatically recognize the drive,

your drive probably wasn’t initialized or was formatted incorrectly.

Note: When you have two drives installed in the duplicator dock and you remove one

of the drives, the other drive temporarily disconnects as well.

Prepare a drive for use

If you install a drive that already has data on it, after you plug in the drive, it appears

under My Computer or Computer with a drive letter assigned to it.

If you install a brand-new drive that doesn’t contain any data, you must prepare the

drive for use.

If you use a computer that’s running a version of Windows®, do the following:

1. On the taskbar, click the Windows icon.

2. In the Search eld, type disk management.

3. In the search results, click Disk Management.

Quick start guide

4. A dialog window appears and asks you to initialize the drive. Depending on the

version of Windows that you’re running, you have the option to create either an

MBR or a GPT disk.

Note: GPT (GUID partition) is required for drives larger than 2 TB but GPT isn’t

compatible with some earlier versions of operating systems. MBR is supported by both

earlier and later versions of operating systems.

5. Locate the disk that is labeled Unallocated. To conrm that the drive is the correct

one, check the drive capacity.

6. Right-click the section of the window that says Unallocated and click New Partition.

7. To initialize the drive in the format of your choice, complete the on-screen

instructions.

When the drive is successfully installed, it appears under My Computer or Computer

with a drive letter assigned to it.

Quick start guide

Remove a drive from your computer

Note: Make sure that the drive that you want to remove isn’t being accessed by the

computer before you proceed.

1. To remove the drive from your operating system, do one of the following:

• On computers running a version of Windows, in your System tray, click Safely

Remove Device.

• On computers running a version of Mac OS, on your desktop, drag the drive to the

trash can icon.

2. Press the POWER button on the top of the duplicator dock and wait for the dock to

nish shutting o.

3. To release the drive, press the Drive eject button on the top of the duplicator dock.

4. Pull the drive from the drive slot.

Warning! Don’t remove your drive from the duplicator dock if the POWER button LED

is blinking, as doing so could damage your drive and result in data loss.

Using the duplicator dock

Duplicate a drive

1. Install the source and destination drives as per the instructions in the Install a drive

topic.

Note: If you’re connecting drives for duplication, place the drive containing the data

that you intend to copy from in the drive #2 slot, and place the drive that you intend to

copy the data to in the drive #1 slot.

2. Turn on the docking station.

3. Press the PC/Copy mode button for 3 seconds until the PC/COPY mode LED is

illuminated red.

4. Wait for the Drive LEDs for each drive to be illuminated blue before proceeding to

step 5.

Note: It may take up to 10 seconds for the LEDs to illuminate.

5. Press the START duplication button to begin duplicating.

The Duplication progress LED indicates how much of the process is complete. When

the drive is duplicated, the entire LED bar will be illuminated.

If the destination drive is smaller than the source drive, the LED for the drive that you’re

duplicating data to will blink red to indicate an error.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali StarTech.com Hardware per computer

StarTech.com

StarTech.com PEX2MPEX Manuale utente

StarTech.com

StarTech.com SM22BU31C3R Manuale utente

StarTech.com

StarTech.com PEX1S552LP Manuale

StarTech.com

StarTech.com UE1205CB Manuale

StarTech.com

StarTech.com PEXUSB311AC2 Manuale utente

StarTech.com

StarTech.com PCI1S950DV Manuale utente

StarTech.com

StarTech.com S32M2NGFFPEX Manuale utente

StarTech.com

StarTech.com PEX16S550LP Manuale utente

StarTech.com

StarTech.com CBUSB220 Manuale utente

StarTech.com

StarTech.com SATSASBAY3BK Manuale utente

StarTech.com

StarTech.com SATSASTRX25 Manuale utente

StarTech.com

StarTech.com PEX4S552B Manuale utente

StarTech.com

StarTech.com PCI1PEX1 Manuale utente

StarTech.com

StarTech.com ECESAT32 Manuale utente

StarTech.com

StarTech.com CARDBUS CB420USB Manuale utente

StarTech.com

StarTech.com EC1U2F Manuale utente

StarTech.com

StarTech.com ECESATA22 Manuale utente

StarTech.com

StarTech.com USBPS2PLATE Manuale utente

StarTech.com

StarTech.com SDOCK1EU3P22 Manuale utente

StarTech.com

StarTech.com CABSHELF22V Manuale utente

StarTech.com

StarTech.com EC230USB Manuale utente

StarTech.com

StarTech.com PCI1PEX1 Manuale utente

StarTech.com

StarTech.com ECUSB3S1 Manuale utente

StarTech.com

StarTech.com ST10GPEXNDPI Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente