StarTech.com 5port Manuale utente
Installation Manual
5PORT
Ethernet Hub
5 Port 10BaseT Micro Hub
1
Overview
The StarTech.com 5 Port 10BaseT micro hub may be small in size, but it is not small on
value. With 5 UTP/STP ports, and the ability to be daisy chained with up to 4 other
hubs, the 5PORT delivers lots of expandability for the future.
Features
• Fully conforms to IEEE 802.3 10BaseT repeater specifications
• Automatic bad port partitioning isolates problem-causing workstations
• Allows data recovery without signal distortion
• LED indicators provide Link/Activity, Collision, Power status
• Uplink port allows for cascade expansion
• Ultra-compact size minimizes equipment space requirements
• Includes AC power adapter (120V) and wall-mounting screws
• 2-year Warranty
Specifications
Getting Started
This section is designed to help you prepare the 5PORT for installation. Please read
through this section carefully before attempting to install the card.
Unpacking the 5PORT
This package should contain:
1 x 5 Port 10BaseT Micro Hub
1 x External power adapter
Standards
Data Transfer Rate
10Mbps Ports
Uplink Port
LEDs
Power
Dimensions
Weight
Operating Humidity
Certification
IEEE 802.3/10BaseT
10Mbps
(5) RJ-45
(1) RJ-45
(5) Link/Activity, Collision, Power
12V DC 0.5A external power adapter
127 x 83 x 30 mm (5.0 x 3.27 x 1.18 inches)
180g (0.4lb)
10~95% (Noncondensing)
FCC Class B, CE Mark
2
Installation
Physical Description
Operating Environment
This hub must be installed and operated within the limits of the specified operating
temperature and humidity (see Specifications). Do not place objects on top of the unit.
Do not obstruct any vents at the sides of the unit. Do not position the hub near any
heating source such as a heater radiator or in direct exposure to the sun. Prevent water
and moisture from entering into the unit. If necessary, use a dehumidifier to reduce
humidity.
5 Port Ethernet Hub
5PORT
Collision LED
Power LED Link/Activity LED
Power Connector RJ45 Connector Uplink Port
Panel
LED
Power
COL
LNK/ACT
(Link/Activity)
Lit
Off
Lit
Off
Lit
Flash
Off
Power is supplied
No Power
Collision detected
in this segment
No Collision
A valid link is
established
Data packets received
No link is established
One for the whole Hub
One
One for each port
Status Description Number of LED
LED
Connecting Network Devices
1. Connect a Category 5 patch cable to the RJ45 jack on your computer’s network card.
(The RJ45 jack looks like an oversized phone jack)
2. Connect the other end of the cable to port 1, 2, 3, 4 or 5 on the hub (not the uplink
port)
3. Repeat steps 1 and 2 for all the computers you want to network.
Uplink to Another Hub
Use the Uplink port (the first port) to connect to another hub. Connecting cables must
comply with EIA.TIA 568 specifications and Category 3, 5 standards to connect hubs.
Connecting the Power
Connect the power cord to the power socket on the external power adapter. Connect the
DC power jack to the DC power socket on the rear panel of the hub. Connect the power
cord to the power outlet. The Power LED on the front panel should be lit.
Troubleshooting
1. Power LED is not lit
• Check if the power cord is properly connected to the external power adapter and the
power outlet. Make sure the DC power jack is firmly plugged into the power socket
of the hub.
2. Link Status LED is not lit
• Check the power switch of the network devices attached to the hub; make sure they
are turned ON. Check the network cables; make sure they are properly connected to
the hub and network devices.
• Check the network cables; make sure the cables are comply with EIA/TIA 568
specification. Use straight-through Category 3 or 5 cables for connection.
3. The first port’s Link Status LED is not lit when it is uplinked to another hub
• Make sure the cable is connected to the uplink port.
• Check the network cable; make sure it is properly connected to both hubs. One end
of the cable should be connected to the uplink port while the other end of the cable
should be connected to a regular port. Do not connect the cable to both uplink ports.
• Check the network cable; make sure the cable complies with EIA/TIA
568 specifications.
4. Collision LED flashes constantly
• Remove all the network cables; connect the cables back on by one to isolate the
source of collision.
• Check the network cable. Inferior cable quality will result in excessive collision and
error packets.
3
Indice
Altri manuali StarTech.com Interruttore
StarTech.com
StarTech.com DS8105 Manuale del sistema
StarTech.com
StarTech.com IES1G52UPDIN Manuale utente
StarTech.com
StarTech.com SV431DPDDUA2 Manuale utente
StarTech.com
StarTech.com ICUSB2328 Manuale utente
StarTech.com
StarTech.com SV231TDVIUA Manuale utente
StarTech.com
StarTech.com MSTCDP122HD Manuale utente
StarTech.com
StarTech.com SV831DUSBA Manuale utente
StarTech.com
StarTech.com MSTMDP122DP Manuale utente
StarTech.com
StarTech.com DS152M Manuale del sistema
StarTech.com
StarTech.com SV231DPU Manuale utente
StarTech.com
StarTech.com C2-D46-UAC-CBL-KVM Manuale utente
StarTech.com
StarTech.com SV231USBA Manuale utente
StarTech.com
StarTech.com C2-H46-UAC-CBL-KVM Manuale utente
StarTech.com
StarTech.com VS421HDDP Manuale utente
StarTech.com
StarTech.com SV231DPUA Manuale utente
StarTech.com
StarTech.com ST3300GU3B Manuale utente
StarTech.com
StarTech.com HB30C4AIB Manuale utente
StarTech.com
StarTech.com SV231DD2DUA Manuale utente
StarTech.com
StarTech.com MSTMDP123DP Manuale utente
StarTech.com
StarTech.com STARVIEW SV231DDUSB Manuale utente
