STC Clear View Manuale utente
7
S
t
r
u
c
t
u
r
e
10
6’ x 8’ Greenhouse
Clear ViewTM
Assembly Instructions
Systems Trading Corporation
450 7th Avenue Suite 2809, New York, NY 10123
P
C
S
H
E
L
L
Introduction
Before Starting Assembly:
5. Make sure you have the proper tools:
After choosing a location, proper preparation of the site is essential. The site must be level. If the site is
not level, create a base slightly larger than the outside dimensions of the greenhouse making a frame of
two by fours lled with either soil, sod or gravel. Make sure the base is square by measuring the diagonals
from both sides to ensure they are equal. The greenhouse is secured from the inside with included pegs.
See step15 for details.
If you decide to have a concrete base, it is best to hire a reliable contractor to build it to ensure it is at and
level. Make sure you have checked with your local authorities regarding any required building permits.
When selecting a site for your greenhouse, a at level area is essential and if possible, with proper water
drainage and easy access to power and water necessary for greenhouse gardening.
Choose a sunny, level position away from overhanging trees and power lines and protected from the
wind as much as possible. The location should be away from structures that could cause snow to drift
on or around the greenhouse.
Locate underground pipes or cables before preparing the site or anchoring the greenhouse.
NOTE: You may assemble the greenhouse on a hard level surface and move it to its nal position when
nished. Make sure there are no obstacles between the assembly area and the nal position.
Thank you for purchasing the 6x8 Clear ViewTM Greenhouse. This greenhouse combines clear window shaped
panels for the sides with the functionality of twin panel polycarbonate panels to help maintain consistent
temperature. Properly assembled and maintained, this greenhouse will provide many years of enjoymen
t.
The List of Parts has the corresponding step number referenced to each part. We recommend that while
you go through the list, make staging areas for each step and place the parts necessary for each step in
these areas. This will save you time and eort during assembly
2. Lay out the parts in separate staging areas:
3. Select a Location:
4. Prepare a Foundation:
1. Make sure you have all the necessary parts:
Compare the contents of the two cartons to the List of Parts. If any parts are missing or damaged or you
have any questions, please contact customer service by phone at (877) 407-9100 ext. 2 or by email at
NOTE: A cordless drill with Phillips head bit is highly recommended.
Tape Measure
Work Gloves
Safety Goggles
Phillips Screwdriver
Spirit Level
Small Step Ladder
Wooden Mallet
Liquid Soap or WD40 Lubricant
Scissors
Hex Key (included)
t
t
t
t
t
t
t
t
t
t
1 of 50
www.stcny.com
Our patented greenhouse has been designed to be easily assembled. All but one step can be completed by
one person. You will need assistance from another person to attach the roof. Although the greenhouse can
be assembled in six to eight hours, we recommend you take your time and make it a weekend project.
These instructions include helpful hints and important information needed to safely assemble and properly
maintain the greenhouse. Please read these instructions completely before you begin.
CAREFULLY READ ALL INSTRUCTIONS BEFORE YOU BEGIN.
FOLLOW THE STEPS IN THE ORDER THEY ARE PRESENTED.
For composting tips, please visit www.ecomposter.net.
2 of 50
www.stcny.com
General Order of Assembly
Step 1: Assemble Back
Step 2: Assemble Door
Step 3: Assemble Front
Step 4: Assemble Sides
Step 5: Prepare Shelves
Step 6: Connect Sides to Back
Step 7: Connect Sides to Front
Step 8: Assemble Roof Vent
Step 9: Assemble and Connect Gables and Roof Vent
Step 10: Brace Sides
Step 11: Install Circular Vent
Step 12: Install Side and Roof Panels
Step 13: Install Trim Plates
Step 14: Hang Door
Step 15: Secure to Ground
Step 16: Install Trays and Bin Holder
Introduction .........................................
Safety Advice .......................................
General Order of Assembly ............
List of Parts ...........................................
Assemble Back ....................................
Assemble Door ...................................
Assemble Front ..................................
Assemble Sides ...................................
Prepare Shelves ..................................
Connect Sides to Back ......................
Connect Sides to Front .....................
Assemble Roof Vent .............................
Assemble and Connect Gables ......
Install Roof Vent ..................................
Brace Sides ............................................
Install Circular Vent ...........................
Install Side and Roof Panels ............
Install Trim Plates ................................
Hang Door ..............................................
Secure to Ground ................................
Install Trays and Bin Holder .............
1
3
4
9
5
8
13
12
14
16
17
10
6
7
11
2
15
Safety Advice
The greenhouse must be positioned and xed on a at level
surface.
Dispose of all plastic bags safely. Keep them out of the reach of
small children.
Keep children and pets away from the assembly area until the
work is completed.
Always wear shoes, gloves and safety goggles when working.
In manufacturing all sharp edges and burs have been removed
but caution should still be taken when handling metal parts.
Do not lean against or push the greenhouse during assembly.
Take special care not to touch overhead power lines with the
aluminium proles.
Do not attempt to assemble the greenhouse in windy or wet
conditions.
Do not position your greenhouse in an area exposed to excessive
wind.
If using power tools or a step ladder always follow the
manufacturers safety instructions.
Hot items such as recently used grills, blowtorches etc. must not
be stored in the greenhouse.
Store the polycarbonate panels in a cool dark place like a garage
until you are ready to use them.
Make sure the greenhouse complies with local building codes.
Table of Contents
1
2
2
3
6
14
17
25
30
31
33
36
37
39
43
44
45
46
48
49
50
G14A
G14C
G14D
2
2
2
Step 5
G14B 2 Step 5
G17A 1 Step 3
G17B 1 Step 3
G17C 1 Step 1
G17D 1 Step 1
Step 5
Step 5
G05D
G05D
G05E
1
1
1
Step 1
Step 9
Step 2
G05B
G06A
G06C 1
1 Step 3
G10A 1 Step 8
G11A 1 Step 8
G12A 2 Step 8
G06B 1 Step 3
G07A 2 Step 4
G07B 2 Step 4
Step 3
Prole QTY
G01A
G02A
G02C
G02D
G02E
G02F
G02G
1
1
2
1
1
1
1
1
4
Step 3
Step 3
Step 3
Steps 1,3
G02B 2 Steps 1,3
Step 1
Step 1
Step 1
Step 9
G02M 1 Step 9
G03A
G03C
G03D
G03F
G03E
G03G
1
2
1
1
3
1
Step 9
Step 9
Step 4
G03B 4 Step 4
Step 1
Step 1
G04C
G04D
G04E
2
2
2 Step 16
G04B 2 Step 4
Step 4
Step 4
Step 9
G03H 1 Step 9
Step 4
G01B
G01C
Prole QTY
G13A 2
1
1
Step 2
Step 2
Step 2
G13B
G13C
3 of 50
www.stcny.com
List of Parts
!
The greenhouse is shipped in two cartons. These cartons are heavy. Be careful when lifting them.
Wear proper safety gear including work shoes, gloves and goggles.
The parts are identied by removable stickers.
Place all the parts for each step in staging areas, checking that you have all parts as you go.
If any parts are missing or damaged, contact STC customer service before beginning assembly:
Clear Panel QTY
1 Step 3
2 Step 1
GY1
1 Step 1GY7
GY2
1 Step 1
GY3
1 Step 3GY5
1 Step 3GY6
1 Step 1GY8
1 Step 3GY9
1 Step 1GY4
Clear Panel QTY
1 Step 2GY10
1 Step 2GY11
4 Step 12GY12
4 Step 12GY13
1 Step 3GY15
4 Step 12Y11
3 Step 12Y12
1 Step 12Y13
1 Step 10Y27
Twin Panel QTY
4 of 50
www.stcny.com
circular vent
vent frame
plastic nut 4
1 Step 11
1 Step 11
Step 11
#S42 screw 4 Step 11
Circular Vent QTY
Steps 1,3,10
Hex Key
S06
S07
S16
G15A
S23
4
1
1
24 Steps 1,3,10
Steps 1,3
8
3 Step 9
Step 10
Step 2
Bracing Parts QTY
1S25 Step 8
Roof Vent Handle QTY
Door Handle QTY
S29
S30
S31
S32
S33
2
1 Step 2
Step 2
Step 2
Step 2
Step 2
1
1
1
5 of 50
www.stcny.com
Connector QTY
16
6
2
Steps 1,4
Step 1
1
Step 3
Step 3
1
Steps 1,3,4
S11
S17L
S17R
S08
S01
12 Steps 5,15S37
2 Step 9
4 Step 4
S22
S20
Connector QTY
4
2
2
Steps 1,3
Steps 1,3
2 Steps 1,3
2 Steps 1,3
Step 4
S05
S09
S10
S04
S03
2 Step 4S19
2 Step 4S39
1 Step 9S21
1
6 Steps 2,3
Step 3
1 Step 1
S28
S18
S12
G09A 2 Step 13
G09B 2 Step 13
J02L 2 Step 13
J02R 2 Step 13
J03 2 Step 13
J04 1 Step 13
Trim Plate QTY
20
J05 Step 16
Shelf Trays QTY
6
6
S34
S35
Step 15
Step 15
Anchor Clip and Peg QTY
Connector QTY
124
7
7
Steps 1,2,9
Steps 1,2,9
Step 8
4 Step 16
Steps 1,2,3,4,8
S13
2
S14
S24
Step 91S42
Step 84S26
S36
S02
Assemble Back
1.1A
1.2A
Secure with S02 screws.
1.1B
Secure each S01 connector
with two S02 screws.
1.2B
26”
(600 mm)
G02B
G02A
S01
QTY
4
6
#S01
#S02
QTY
1
1
1
1#G03C
#G03D
Prole Connector
QTY
Prole
#G02A
#G02B
Line up bottom hole on short side of
connectors S01 with hole on side of
proles G03C and G03D.
Slide short side of connector S01 into channels of proles G02A and G02B.
Line up last hole on connector S01 with hole in each prole.
26”
(600 mm)
G03C G03D
S01
S02
S02
!
Lay out all the parts for the back face in a staging area.
Make sure the pieces are in the correct positions before assembling.
Carefully follow the order of assembly to ensure an easy installation.
Wear proper safety gear including work shoes, gloves and goggles.
!The back is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE.
IMPORTANT: The holes are not at the midpoint of the prole.
Arrange prole so the 26” portion will be the bottom when standing.
6 of 50
www.stcny.com
NOTE: ALL VIEWS ARE FROM INSIDE.
1.3A
1.3B
Secure with four S02 screws.
G02B
G03D
G03C
G03C G03D
G02A
G17D
G17C
G02A
G02B
Attach proles G02B and G03C to prole G17C by sliding the long sides of connector S01
into channels lining up last hole in S01 with holes in prole G17C. Attach proles G03D
and G02A to prole G17D by sliding the long side of connector S01 into prole
channels lining up last hole of S01 with holes in G17D.
7 of 50
www.stcny.com
NOTE: ALL VIEWS ARE FROM INSIDE.
QTY
QTY
1#G17D
1#G17C
Prole Screw
4#S02
G17C
G17D
G17C
Slide connectors S08 into channels of proles G03C and G03D.
1.4A
1.5
1#S05#S04
QTY
QTY
1
Connector Connector
QTY
1#G01B
Prole
QTY
4
2
#S02
#S08
Connector
S05
S04
G01B
S04
G01B
S05
G01B
Slide connectors S04 and S05 into prole G01B until they securely click into place.
Secure with four S02 screws.
1.4B
8 of 50
www.stcny.com
G02B G03C
S08
S08
S08
S02
G03D
G02A
NOTE: ALL VIEWS ARE FROM INSIDE.
Connectors S04 and S05 CLICK into place.
There is only one way to properly fasten connectors into proles. Line up parts
rst to ensure correct placement. Slide connectors until they CLICK securely into
prole. Use WD40 or liquid soap if pieces do not easily slide together. Wear gloves.
!
Altri manuali per Clear View
3
Indice
Altri manuali STC Kit serra
