Steelcase Avenir Manuale utente
Page 1 of 3
939501454 Rev A
Avenir®Cable Connect Box
®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2004 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
FACEPLATE (AT&T)
FACEPLATE (AMP)
BOX HALF
WINDOW
BOX HALF ASSEMBLY
DOUBLE FACED TAPE
COVER PLATE
HANGER BRACKET
LH SHOWN - RH TYPICAL
HANGER BRACKET
ELECTIVE ELEMENTS
BASE
5/32” Bit
Page 2 of 3
939501454 Rev A
1a.
1b.
HANGER BRACKET
LH SHOWN - RH TYPICAL
BOX HALF ASSEMBLY
ELECTIVE
ELEMENTS
BRACKET
(NON HANDED)
PANEL ASSEMBLY
SERIES 9000
VALENCIA
AVENIR
ELECTIVE
ELEMENTS
BLUNT NOSE SELF TAPPING SCREWS
DOUBLE FACED TAPE
WORKSURFACE
Cable connect box assembled onto
structural panels
1a. Select the proper style bracket, either a right
or left hand hanger bracket for Series 9000,
Valencia and Movable Walls panels or the (non-
handed) Elective Elements hanger bracket.
Secure bracket to the back side of box half with (2) self
tapping screws. Hook assembly onto panel
assembly. Proceed to Step 2.
Cable connect box assembled onto the
top of a desk or worksurface
1b. Secure rear cover plate to box half assembly
with (2) screws. Remove protective paper form
one side of double faced tape and apply onto side
of box half assembly. Remove remaining
protective paper from tape and adhere box half
assembly onto a desk or worksurface in desired
location. Proceed to Step 2.
REAR
COVER
PLATE
8-32 X 3/8” BLUNT NOSE
SELF TAPPING SCREW
Page 3 of 3
939501454 Rev A
2.
1c.
BOX HALF ASSEMBLY
BASE
FACEPLATE (AT&T)
FACEPLATE (AMP)
BOX HALF
WINDOW
TO BE INSERTED IN UNUSED
OPENING AS REQUIRED
BOX HALF
ASSEMBLY
Cable connect box assembled under
bottom of desk or worksurface
1c. Secure base to back side of box half
assembly with (2) screws. Locate box half
assembly to a desired location and use as template
to drill (2) 5/32” dia. holes 3/4” deep into the bottom
of worksurface. Attach with (2) screws. Proceed to
Step 2.
NOTE: For steel worksurfaces, drill holes into hat
section braces.
2. Install cable windows as required. (windows
may be broken in half for a smaller dia. cable
passage). Position box half and desired face plate
and secure with required screws.
NOTE: Some prewiring may be required!
SCREW 10 X 7/8”
WORKSURFACE HOLES
5/32” X 3/4” DEEP
NOTE: MARK OR TAPE
DRILL FOR 3/4” DEPTH
8-32 X 3/8” BLUNT
NOSE SELF
TAPPING SCREW
Altri manuali Steelcase Decoder via cavo
Manuali Decoder via cavo popolari di altre marche
StarTech.com
StarTech.com BOX4CABLE Manuale utente
Commercial Electric
Commercial Electric 5053-WH Manuale utente
Motorola
Motorola DCT6412 DUAL-TUNER DVR AND HD SET-TOP - MICROSOFT... Istruzioni per il montaggio
Renkforce
Renkforce 1395556 Manuale utente
Huawei
Huawei FAT9102SD-32G Manuale utente
VISSEM Electronics
VISSEM Electronics Opticube VSOF-OTB-E Manuale utente
