SteelMax D1PRO Manuale utente
Steelmax Tools LLC
112 Inverness Circle East, Englewood, CO. 80112
1-87STEELMAX Fax 303-690-9172
www.steelmax.com
e-mail:
sales@steelmax.com
SAFETY INSTRUCTIONS
AND OPERATORS MANUAL
FOR
DRILLING MACHINE
D
D1
1P
PR
RO
O
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 2 -
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 3 -
CONTENT
1. GENERAL INFORMATION ...................................................................................................... - 4 -
2. GENERAL SAFETY ADVICE ................................................................................................... - 5 -
3. STANDARD EQUIPMENT ....................................................................................................... - 7 -
4. START UP AND OPERATION ................................................................................................. - 8 -
5. TECHNICAL DATA ................................................................................................................ - 19 -
6. MAINTENANCE AND SERVICE ............................................................................................ - 22 -
7. PARTS LIST AND EXPLODED PARTS DRAWINGS............. .............................................- 23 -
8. ELECTRICAL DIAGRAM ....................................................................................................... - 33 -
9. CE DECLARATION OF CONFORMITY................................................................................. - 34 -
10 MACHINE TEST CERTIFICATE ............................................................................................ - 35 -
11. WARRANTY CARD................................................................................................................ - 36 -
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 4 -
BEFORE YOU START WORK WITH THE MACHINE,
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND USE ALL RECOMMENDATIONS.
1. GENERAL INFORMATION
Portable drilling machines with electromagnetic bases are fast becoming very
universal power tools not only at steel fabricating workshops or steel building sites
but also at every factory maintenance workshop, truck manufacture & repair
company, military equipment service, onboard ship maintenance shop etc.
But full advantages of electromagnetic drilling machines can be achieved only
with optimal tooling. Milling cutters are designed and manufactured specifically for
use with these machines and offer a whole range of advantages such as 3 inch
diameter holes through more than 2 inch steel, in one pass and with precision not
otherwise attainable without heavy stationary equipment.
The D1 PRO machine is capable of milling 40 mm (1-9/16") holes trough 2
inch plate what is totally unique for an electromagnetic drill of this size and weight.
The D1 PRO is equipped with a powerful verified for many years of exploitation drive
and electromagnet with field control system.
Before you start work with the machine, please read these instructions
carefully. Take special note of safety recommendations.
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 5 -
2. GENERAL SAFETY ADVICE
Drilling machine must not be used when:
1. The operator has not read the Operator’s Manual.
2. The work to be done is not in agreement with these recommendations.
3. Drilling machine is not complete or has been repaired with non-original parts.
4. Power supply parameters do not conform to those stated on the motor’s plate.
5. Machines operator has not checked condition of the drilling machine, condition of
power cable, control panel or cutter.
6. Power supply socket is not equipped with a protection circuit.
7. Machine is not secured with safety chain as a protection from dropping from
power loss especially when used at heights or in vertical or upside-down
positions.
8. Bystanders are present in the immediate vicinity of machine.
Warning!
Read and save all instruction for future reference!
Important rules of safe use of drilling machine
1) Before attempting to work with the machine check condition of electrics
including power cord and plug.
2) The drilling machine should be connected to an installation equipped with
protection circuit (neutral or ground) and protected with a 16 A fuse for 220V
and 32 A fuse for 120V.
When used on building sites, it must be supplied
through a separation transformer made in the second class of protection
3) Machine can be used outdoors, but is not weatherproof. Do not expose to rain,
snow or frost.
4) Machine should not be used on: rusty surfaces, steel plates covered with thick
paint, uneven surfaces or next to a welding machine. When the machine is
attached to any metal surface, that surface should not be welded. Remove the
drill from the steel before beginning welding. This can cause damage to the
machine and will void the warranty
.
5) In all cases always use a safety chain/strap (see drawing 1). The safety chain
mustn't be loose! To avoid this situation the safety chain should be wrapped
around the element it is hooked to.
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 6 -
Safety chain can also secure the drill through
the handle.
6) Do not use the machine in explosion hazard zones.
7) Do not start work if the machine has excessive play on guide slides.
8) Always wear safety goggles and ear protection.
9) Do not remove metal chips with bare hands.
10) Do not touch the spindle and the cutter during work.
11) Tools must be fastened firmly. When a milling cutter is used, check before start
of work if tool holding screws are fastened tightly.
12) Do not use dull or damaged cutters.
13) Do not use milling cutter without pilots, and arbors without ejection spring.
Do not touch or replace the tool with power source on – while
electromagnetic base is being used.
14) Use tools recommended in Operator’s Manual only.
15) After use, always clean metal chips and coolant from drilling machine.
16) Always unplug machine from power supply during any work on the machine.
17) Before each use the machine should be checked for the presence of damage
and the proper and consistent use. Check whether any of the parts are broken
and that all the parts are fastened properly.
Drawing 1.
E
x
am
p
les how
s
a
f
et
y
chain
s
hould be
f
astened..
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 7 -
18) If the machine falls on a hard surface, from a height, is wet or is subjected to
other unfortunate events that could affect its technical state - work should be
terminated immediately and the machine should be sent to service for
inspection as soon as possible.
The drill should not be used on steel thinner than (less than 3/8” (10
mm)). On thin steel (less than 3/8” (10 mm)) the magnet’s adhesive power
would be significantly reduced which can cause machine failure or
individuals injury. The machine should be located on the work piece with
the entire surface of the electromagnetic base! It is recommended that each
time, before positioning the machine the electromagnetic base should be
cleaned with a rag or sanded down with abrasive paper!
Please keep all recommendations.
3. STANDARD EQUIPMENT
D1 PRO comes in a standard equipment set which consists of:
metal box - 1 pc
drilling machine - 1 pc
cooling system - 1 pc
2.5 Allen Key - 1 pc
3 Allen Key - 1 pc
4 Allen Key - 1 pc
8 mm flat wrench - 1 pc
spoke handles - 3 pcs
safety chain with snap hook - 1 pc
operator’s manual - 1 pc
plastic box - 1 pc
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 8 -
4. START UP AND OPERATION
4.1 Cutters and optional equipment features.
This drilling machine’s spindle has a Weldon Shank type socket 3/4” or
19.05 mm and is specifically designed for use with milling cutters.
Milling cutter (2) is located inside arbor body (1) and is fastened with screws
(3). While fastening the cutter in the socket, be aware that screws should be screwed
tight so that they do not come loose. It is important to position the cutter in relation to
the socket in such a way that the flats on the cutter shank are positioned under the
fixing screws (3). Both fastening screws(3) should be used to secure the cutter. Pilot
(5) is located inside the cutter. It makes it easier to position milling cutter over the
center of a planned hole. During drilling as the cutter goes deep into steel, the pilot
moves back into the arbor body and tightens discharge spring (4). That spring ejects
slug which is a by-product of milling a hole with a center free cutter. The pilot also
allows cutting fluid to cool and lubricate the cutter from the inside.
Basically milling cutters are designed to make through holes. On occasions when
there is a need for an overlapping hole the pilot should not be used.
Drawing 2.
Principle of milling cutter’s work
Drawing 3.
A few types of holes that can be done with a milling cutter
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 9 -
4.1.1 Installing and uninstalling the arbor
The arbor installation and removal should be carried out when the
machine is turned off and disconnected from the power grid!
Installing the arbor:
a) Raise the drive and the slide (1) up using the lever (3);
b) Raise the guard,
c) Clean the spindle (2) using a cotton cloth,
d) Before mounting, clean off the lubricant from the new arbor (4),
e) Place the arbor on the spindle, so that the flat sides of the spindle are under the screws
(5)
f) Tighten the screws securely (5)
Uninstalling the arbor:
a) Raise the drive and the slide (1) up using the lever (3);
b) Raise the guard in order to attain access to the arbor (4) screws (5).
c) Loosen the screws (5);
d) Remove the arbor (4).
D1PRO
D1 PRO 11-2011 Operators manual for D1 PRO Drilling Machine - 10 -
4.1.2 Installing and uninstalling the milling cutter
Milling cutter installation and uninstallation should be carried out when the
machine is turned off and disconnected from the power grid!
Installing the milling cutter:
1. Raise the drive and the slide (1) up using the lever (2);
2. Raise the guard in order to attain access to the arbor (4) screws (3);
3. Insert the appropriate type of pilot (5) into the milling cutter (6);
4. Position the milling cutter (6) with the cutter facing up, so that the flat sides of the
milling cutter are under the screws (3)
5. Put the milling cutter (6) into the arbor socket (4);
6. Tighten the screws securely (3).
Uninstalling the milling cutter:
1. Raise the drive and the slide (1) up using the lever (2);
2. Raise the guard in order to attain access to the arbor (4) screws (3).
3. Loosen the screws (3);
4. Remove the milling cutter (6) and the pilot (5) from the arbor socket (4).
Altri manuali per D1PRO
1
Indice
Altri manuali SteelMax Trapano
SteelMax
SteelMax D3X RS Manuale utente
SteelMax
SteelMax SM-D1 Manuale utente
SteelMax
SteelMax D200XT Manuale utente
SteelMax
SteelMax D3X R Manuale utente
SteelMax
SteelMax D2X Manuale utente
SteelMax
SteelMax D300XT Manuale utente
SteelMax
SteelMax D1 AUTO Manuale utente
SteelMax
SteelMax D4X Manuale utente
SteelMax
SteelMax D2X Manuale utente
SteelMax
SteelMax SM-D1 Manuale utente
SteelMax
SteelMax D1 Pro-X Manuale utente
SteelMax
SteelMax D1 AUTO Manuale utente
SteelMax
SteelMax SM-D2 Manuale utente
SteelMax
SteelMax D250X Manuale utente
SteelMax
SteelMax SM-D1 Manuale utente
SteelMax
SteelMax D1 AUTO Manuale utente
SteelMax
SteelMax D4X Manuale utente
SteelMax
SteelMax D1PRO Manuale utente
