Stewart Filmscreen Visionary Manuale utente

1 Stewart Filmscreen

Visionary

Retractable, Above Ceiling, Self-Finishing Screen System with Two-Piece Construction

Stewart Filmscreen –Visionary 2

Stewart Filmscreen reserves the right to make changes to the product specified in this document.

Sizes and specifications subject to change without notice at the manufacturer’s discretion. From time to time,

this document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at:

www.StewartFilmscreen.com

Revision 1.01.03

Date: 04/26/2022

Stewart Filmscreen –Visionary 3

Visionary

O W N E R ’ S M A N U A L

Contents

To the Owner...................................................................................................................4

About Visionary ...............................................................................................................5

Preparing the Installation.................................................................................................6

Ceiling Mount ..................................................................................................................8

Electrical........................................................................................................................10

Optional Intelligent Motor Control (IMC).........................................................................12

IMC Wiring Diagram......................................................................................................14

Optional Low Voltage Control (LVC)..............................................................................15

Optional Low Voltage Control with IR ...........................................................................16

LVC Wiring Diagram .....................................................................................................17

Optional High Voltage Wall Switch (HVS)......................................................................18

Optional Video Interface Control System (VICS) ...........................................................19

Installing the Screen Assembly into the Case................................................................20

Operating the Screen ....................................................................................................21

Limit Switch Adjustment.................................................................................................22

Caring for and Cleaning the Screen...............................................................................24

Troubleshooting.............................................................................................................25

One (1) Year Limited Warranty......................................................................................27

Stewart Filmscreen –Visionary 4

TO THE OWNER

Congratulations on purchasing the finest optical viewing screen in the world.

Your handcrafted Visionary projection screen has been carefully inspected to ensure your

optimal viewing experience will last for many years. Please take a moment to review this

manual. It will guide you through the installation and the operation of your screen and will also

provide you with detailed instructions on how to care for your screen’s viewing surface.

From all of us at Stewart Filmscreen, we would like to thank you for choosing Visionary. Should

you have any questions, please don’t hesitate to contact our customer service department at 1

(310) 784-5300, or toll free at 1 (800) 762-4999. We’re here to help.

Salvador Villalvazo

Large Electric Screen Craftsman

Stewart Filmscreen –Visionary 5

ABOUT VISIONARY

The Visionary is designed for ease of installation. The case can be installed separately during

construction, and the screen assembly is then installed once the construction is completed. The

Visionary features a seamless, self-finishing face-plate and drywall stops to accommodate various

ceiling configurations.

IMPORTANT SAFETY INFORMATION

Carefully read the instructions.

This screen must be installed by a qualified electrician.

For supply connections, use wires rated for at least 75 C.

Use copper or aluminum conductors.

For indoor use only.

Do not connect low voltage to line voltage power.

Earth ground terminal connection must be made as shown in wiring diagrams.

Proper short circuit and overload protection must be provided at the circuit breaker distribution

panel. You may use up to a 20 amp maximum circuit breaker with adequate short circuit breaking

capacity for your installation.

USING THIS MANUAL FOR INSTALLATION

If you are using this manual to install the Visionary screen, you should be aware that the factory

advises against installing a concealed or recessed electrical projection screen permanently. You

must be able to access and remove the unit should future service be necessary.

For the instructions related to your specific controls, refer to the appropriate page:

IMC (see Page 12)

LVC (see Page 15)

HVS (see Page 18)

VICS (see Page 19)

⚠

NOTE

This owner’s manual may describe options and features not equipped to the specific

screen you have purchased.

Stewart Filmscreen –Visionary 6

PREPARING THE INSTALLATION

Before proceeding with the installation of this screen, take time to thoroughly read and understand

these installation instructions. Failure to comply with the instructions contained in this manual

may result in voiding your warranty.

SPECIFICATIONS

Specifications regarding the individual screen dimensions, weight, etc., are provided by the

factory when the unit is ordered.

Before beginning the installation

Check the size and weight of the screen to be installed so that you can plan for the number

of people required for installation.

Youwillneed at least two people to mount a small screen. More are needed for larger,

heavier screens.

Read everything before you do anything!

What’s inside the box?

Inside your Visionary unit box, you will find everything needed to get started enjoying your

Stewart screen:

Visionary unit preassembled and prewired

Packing material

Control option

Visionary Quick Start Guide

You will need

A level

A drill

A drop cloth

Tools for tightening fasteners

Ladders for the personnel supporting the screen during the mounting process

Fasteners appropriate for the surface on which the screen is being mounted

Stewart Filmscreen –Visionary 7

PREPARING THE INSTALLATION (CONTINUED)

Note: Bolts and other fasteners for the screen are standard gauges and sizes used in the U.S.,

regardless of the installation country. For this reason, sizes are expressed in inches rather than

metric measurements.

Unpacking

Be sure to unpack carefully in a clean area. Use special care when handling the screen so that it

does not become soiled or damaged. If you plan to repack your screen and hardware for

transportation to another location, you may want to photograph or make a note of how it was

packed. Retain the packing material for future use, if desired.

Remove the outer plastic covering and white

wrapping paper surrounding the screen case.

Do not remove the wrapping paper surrounding the

screen roller. You should remove it only after the

unit is hung and all electrical connections have

been made.

Removing the screen assembly from the case

The unit is shipped with the screen assembly

fastened inside. Prior to mounting the unit, you

must remove the screen assembly from the case.

Using the supplied wrench, loosen the bolts shown

in Figure 1. There is a bolt inside each end of the

screen slot.

⚠

CAUTION

Do not stand on the screen case or store it on its end. This will cause screen damage. If

you are not going to install the screen immediately, make sure it remains horizontal

during storage. Note: Failure to comply with the instructions and guidance

contained in this manual may result in voiding your warranty.

Supplied Wrench

Figure 1. Visionary bottom view,

removing bolt holding screen assembly

Stewart Filmscreen –Visionary 8

CEILING MOUNT

Professional mounting techniques should be used. Stewart Filmscreen cannot be liable for

substandard or faulty installations. Failure to comply with the instructions and guidance

contained in this manual may result in voiding the warranty.

1. Use a magnetic stud finder, or similar appropriate means, to

identify the location of solid ceiling joists. If the joists or

rafters are parallel to the screen case, blocking is required

between structural elements.

2. Mounting hardware must be mounted into solid wood. If no

joists are available then the ceiling must be blocked.

3. Lift the case up to the ceiling and screw the ceiling brackets

into the joists on both ends of the case (see Figure 3) or

suspend the case (see Figure 2).

4. Ensure that all four mounting holes are being utilized to

maximize mounting strength.

5. For the minimum clearance dimensions for ceiling mount,

(see Figure 4).

⚠

CAUTION

During installation, do not place the unit on an unstable cart, stand, table or ladder.

The unit may fall, causing injury to you or others as well as cause possible damage

to the unit.

Do not mount to drywall only. There must be wood joists behind the drywall to

secure the screen.

Figure 2. Visionary unit

suspended from ceiling

Figure 3. Visionary bottom view

fastened to ceiling joints

Stewart Filmscreen –Visionary 9

CEILING MOUNT (CONTINUED)

Figure 4. Ceiling mount detail

with minimum clearance

Stewart Filmscreen –Visionary 10

ELECTRICAL

The Visionary screen system can be controlled through several remote control devices (IR and RF),

keypads, dry contact outputs, internet protocol (IP), and low-voltage trigger outputs.

Note: This manual refers to AC (electrical alternating current) to represent electrical power. Your

location may use 120 V, 220 V, or other electrical power. Screen systems are manufactured using

the electrical power type specified for the location. Use appropriate power sources for your location.

MOTOR WIRING

The Visionary screen system’s motor is prewired at the factory. No additional motor wiring is

required.

The following pages will outline standard and optional control types for Visionary.

Connections

The following Stewart Filmscreen control options are available for Visionary when placing your

order. Please refer to the appropriate section to learn more about each control system.

IMC (Intelligent Motor Control)

LVC (Low Voltage Control)

HVS (High Voltage Wall Switch)

VICS (Video Interface Control System)

⚠

CAUTION

Visionary is to be installed and used within the scope of the appropriate electrical

codes and regulations. Failure to do so may cause malfunctioning or damage to the

screen.

Indice

Altri manuali Stewart Filmscreen Schermo di proiezione

Stewart Filmscreen

Stewart Filmscreen Fixed Frame Screen Manuale utente

Stewart Filmscreen

Stewart Filmscreen C Manuale utente

Stewart Filmscreen

Stewart Filmscreen 4-Way ScreenWall ElectriMask Manuale utente

Stewart Filmscreen

Stewart Filmscreen Cine-W Manuale utente

Stewart Filmscreen

Stewart Filmscreen AT 1.5 Manuale utente

Stewart Filmscreen

Stewart Filmscreen Balon Series Manuale utente

Stewart Filmscreen

Stewart Filmscreen Luxus Manuale utente

Stewart Filmscreen

Stewart Filmscreen RP-1013 Manuale utente

Stewart Filmscreen

Stewart Filmscreen Vertical ES EM Manuale utente

Stewart Filmscreen

Stewart Filmscreen B Manuale utente

Stewart Filmscreen

Stewart Filmscreen Visionary Electriscreen Manuale utente

Stewart Filmscreen

Stewart Filmscreen LCD Rear-Projection TV Manuale utente

Stewart Filmscreen

Stewart Filmscreen AB Electriscree Manuale utente

Stewart Filmscreen

Stewart Filmscreen Balon Series Manuale utente

Stewart Filmscreen

Stewart Filmscreen Visionary Medio Manuale utente

Stewart Filmscreen

Stewart Filmscreen Balon Series Manuale utente

Stewart Filmscreen

Stewart Filmscreen Cima Istruzioni originali

Stewart Filmscreen

Stewart Filmscreen Luxus ScreenWall Series Manuale utente

Stewart Filmscreen

Stewart Filmscreen VistaScope Manuale utente

Stewart Filmscreen

Stewart Filmscreen Luxus Manuale utente

Stewart Filmscreen

Stewart Filmscreen WallScreen 2.5 Manuale utente

Stewart Filmscreen

Stewart Filmscreen A Electriscreen Manuale utente

Stewart Filmscreen

Stewart Filmscreen Cabaret Manuale utente

Stewart Filmscreen

Stewart Filmscreen Stealth Trapdoor Electriscreen Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Da-Lite

Da-Lite ExecutiveElectrol Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

Elite Screens

Elite Screens M85XWS1-SRM Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

Elite Screens

Elite Screens Starling 2 Series Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente