Sunny CCU12V-30 Series Manuale utente
Test
Central Battery Control Unit CCU12V-30 Series
Test
LED AC Indicate that the unit is receiving power.
LED Charge/Full Gives information on battery charging.
LED ON Indicate the unit is ready for operation.
Switch ON Press to turn on the lamp (while the unit is not plugged in).
Switch OFF Press to turn o the lamp (while the unit is not plugged in).
Switch Test For testing the device’s availability. (during normal circumstance)
1. Controlled by a highly intelligent 8-bit micro controller.
2. The unit uses high quality LEDs providing bright and constant illimitation throughout
its operation with a lifetime of over 50,000 hours (when used in conjunction with
our recommended equipment).
3. The fully sealed “SUNNY” lead-acid battery is totally maintenance-free throughout
its operational life.
4. The unit’s case is made out of 1mm thick Electro-Galvanized metal sheets coated
with epoxy powder and stove enamel and is highly resistance to rust.
USER MANUAL
Status Indicators and Testing Buttons
Features
1. Check to make sure that the power socket of the home or building is providing
a 220 VAC current. If not please resolve the issue first before installing the unit.
2. Install the unit properly at the location where emergency light is needed. Check to
make sure the unit is properly secured to prevent possible accidents.
3. Check that the load electrical wire is in good working order. If so, connect it to the
Terminal Output and screw tightly to prevent any electrical sparks that could cause
fire.
4. Press the “ON” switch and hold down for about 3 seconds. The unit will then provide
power to the emergency lamp and the “LED ON” will turn on.
5. Plug the unit into a socket that provides a 220VAC power supply.
6. The AC LED light will show if the unit is receiving power from the power socket.
The Charge/Full LED will blink if the battery is charging and will remain on when the
battery if fully charged.
7. During operation press the TEST button to perform an operational test.
The emergency light should turn on for 5 seconds and then turn o automatically.
1. Always press the “ON” switch every time after installation to turn on the unit.
2. When the unit is not in use always turn it o by pressing the “OFF” switch.
3. The unit should be installed indoors away from direct sunlight and rain or moisture.
4. The unit should be stored in temperatures under 25 Degree Celsius and the battery
should be charged every 3 months to maintain its operational life
Installation and Operation
Important Note on Using the Unit
SIDE VIEWBACK VIEWFRONT VIEW
220Vac
W 80
061H
203
L 290
0
61H
L 290
061H
Test
Dimension (mm)
- Power not getting to the unit
after plugging in.
The LED AC light does not
turn on.
- The power socket might not have
any power.
- The plug or socket is loose.
- The AC.220V fuse is blown.
- Check the 220VAC power supply.
- Check the plug and socket.
- Contact customer service.
- Emergency light does not
turn on after the power went
out.
- Emergency light only turns
on for a short time after the
power went out.
- The battery is not fully charged.
- The battery has degraded.
- Fully charge the battery.
- Contact customer service to
replace the battery
ProblemCause What to do
- The unit is not plugged in.
- The battery terminals are not
connected.
- The lamp is faulty.
- The load wiring is loose.
- The DC fuse has blown
- Check the unit’s power socket.
- Connect the battery terminals.
- Contact our customer support
department.
- Check the load wiring.
- Contact our customer support
department.
Initial Trouble Shooting
For any further questions about your product
please feel free to contact SUNNY’s customer
service department.
Tel. (+66) 02-948-4450-2
E-mail: [email protected]
1. The product will only be under warranty if the customer fills in the “warranty card”
and return the “return part” to the company within 7 days of purchasing the product.
If this is not done within the specified time then the warranty will be considered void.
2. The warranty only covers the unit’s internal parts for the duration specified by the
company counting from the date of purchase.
3. Please show the warranty card every time when contacting our service department
or the dealer you purchased the unit from.
4. The warranty will be considered void in the following cases.
The unit has been used outside of its intended use specified in the manual.
The unit has been used with equipment that does not meet the specifications
specified within the manual.
The unit has been damaged from impact, for example parts are dented, scratched
missing or distorted.
The unit has been modified or repaired by people not ocially certified by our
company.
The Sticker Warranty Void has been removed or torn.
The unit is damaged from negligence or incompetent use, for example, the
battery is swollen, the batter has been overcharged, the battery has been
damaged from quick charging, the battery has been short-circuited, the battery’s
charged has been completely drained.
The unit has been stored improperly, for example, it was exposed to moisture
causing rust and damage to the internal circuitry.
Damaged was caused by a malfunction in the AC power supply.
Damage from natural disaster such as fire, moisture, submersion in liquids,
chemical damage or from unavoidable circumstances.
Damage from animals or insects.
Note : Please read the manual carefully before installation and operation to understand
how to properly operate the unit.
Terms for Warranty and Service
IsOn Import-Export Co., Ltd.
2915-2917 Ladprao Road, Klongjan,
Bangkapi, Bangkok 10240
Altri manuali Sunny Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
