Sunrise telecom HTT Manuale utente

1HTT

SUNRISE TELECOM

HT T

Home Test Toolkit

www.sunrisetelecom.com

User’s Manual

SA976

HTT

PASS/FAIL

BLUETOOTH

POWER

BATTERY

F1 F2 F3 F4

AUTO ESC

SIGNAL

2 SA976

WARNING

Using the supplied equipment in a manner not speciﬁed by Sunrise Telecom may impair

the protection provided by the equipment.

End of Life Recycling and Disposal Information

DO NOT dispose of Waste Electrical and Electronic Equipment (WEEE) as unsorted

municipal waste. For proper disposal return the product to Sunrise Telecom. Please

contact our local ofﬁces or service centers for information on how to arrange the return

and recycling of any of our products.

• America: SUNRISE TELECOM INCORPORATED

302 Enzo Drive, San Jose, CA 95138, USA

Tel: +1-800-701-5208, +1-408-360-2200 Fax: +1-408-363-8313

Email: support@sunrisetelecom.com

• Germany: SUNRISE TELECOM GERMANY GmbH

Buchenstr. 10, D-72810 Gomaringen, GERMANY

Tel: +49-7072-9289-50 Fax: +49-7072-9289-55

Email: inf[email protected]

• Europe: SUNRISE TELECOM PROTEL

Via Jacopo Peri, 41/c, 41100 Modena - ITALY

Tel: +39-059-403711 Fax: +39-059-403715

Email: europe.service@sunrisetelecom.it

• Asia: TAIWAN SUNRISE TELECOM Company Limited

21, Wu Chuan 3rd Road, Wu-Ku Hsiang, Taipei County, 248, Taiwan, R.O.C.

Tel: +886 2 2298 2598 Fax: +886 2 2298 2575

Email: support@sunrisetelecom.com

EC Directive on Waste Electrical and Electronic Equipment (WEEE)

The Waste Electrical and Electronic Equipment Directive aims to minimize the

impact of the disposal of electrical and electronic equipment on the environ-

ment. It encourages and sets criteria for the collection, treatment, recycling,

recovery, and disposal of waste electrical and electronic equipment.

MAN-22461-001 Rev B00

This device uses software either developed by Sunrise or licensed by Sunrise from third

parties. The software is conﬁdential and proprietary. The software is protected by copy-

right and contains trade secrets of Sunrise or Sunrise’s licensors. The purchaser of this

device agrees that it has received a license solely to use the software as embedded in the

device, and the purchaser is prohibited from copying, reverse engineering, decompiling,

or disassembling the software.

3HTT

HTT

Introduction.................................................................... 5

Getting Around ...................................................................................5

1 Physical Description ................................................ 7

1.1 Front View ...................................................................................7

1.2 Top Side Panel ...........................................................................8

1.3 Right Side Panel .........................................................................9

1.4 Bottom Side Panel .....................................................................9

1.5 Back Side ...................................................................................9

1.5.1 Battery Replacement ...............................................................9

1.5.2 Battery Care and Storage ......................................................10

2 Auto Key.................................................................. 13

3 Expert Mode Menu ................................................. 15

3.1 VDSL VTU-R .............................................................................16

3.1.1 Current Status .......................................................................17

3.1.2 Tone Table .............................................................................19

3.1.2.1 Bits/Tone ............................................................................19

3.1.2.2 SNR/Tone ...........................................................................21

3.1.3 Link Measurement .................................................................22

3.1.4 Modem Setup ........................................................................24

3.2 POTS/DC/OHM ........................................................................25

3.2.1 POTS .....................................................................................26

3.2.2 DC Voltage ............................................................................27

3.2.3 Ohm .......................................................................................28

3.3 Cable Testing ............................................................................29

3.3.1 Coaxial Cable Loss ...............................................................31

3.3.2 RJ Cable Loss .......................................................................32

3.3.3 Wiremap ................................................................................33

3.3.4 Cable ID .................................................................................34

3.3.5 Tone Generation ....................................................................35

3.4 HPNA Analysis .........................................................................36

3.5 Wireless (802.11) ......................................................................39

3.6 SLM ..........................................................................................39

4SA976

3.7 Ethernet ....................................................................................40

3.8 PC Access ................................................................................41

3.9 Measurement Setup .................................................................41

3.10 System Setup .........................................................................42

3.10.1 Clock ...................................................................................42

3.10.2 Backlight ..............................................................................43

3.10.3 Auto Off ...............................................................................43

3.10.4 Battery .................................................................................44

3.10.5 Project .................................................................................44

3.10.6 Prole ..................................................................................45

3.10.7 View Store ...........................................................................45

3.10.8 System Information .............................................................45

4 General Information ............................................... 47

4.1 Customer Service .....................................................................47

4.2 Testing and Calibration Statement ...........................................47

4.3 Express Limited Warranty ........................................................48

Index ............................................................................. 51

5HTT

Introduction

Welcome to the HTT.

This User’s Manual describes the general structure of the HTT along

with it’s functions.

Contained within the shipping box are the following items:

HTT Test Set, Carrying Case, AC Charger, and User’s Manual: The

charger can simultaneously charge the battery and run the test set.

Cable ID Devices: These are used to identify coax or RJ runs into

each wall jack in the residence.

Wiremap Probe: Used primarily for Cable Loss and Wiremap test-

ing.

Cable Testing Cable: This is an RJ-45 to RJ-11/Coax connection cable

used for Cable Loss, and Cable ID testing. The single RJ-45 connects

to the HTT, and other ends connect to the circuit under test.

RJ-11 to clips Cable: Used for VDSL and POTS/DC testing.

RJ-11 to Coax Cable: Used for VDSL testing on Coax.

Coax Cable: Used for SLM or HPNA testing.

RJ-11 to RJ-11 Cable: Used for POTS/DC, VDSL, or HPNA testing

via an RJ-11 jack.

F-type Snap On Connector: Used on Coax cables to facilitate con-

nection.

F-type to F-type Barrel Adapter Coupler: Used to connect two ends

of male Coax cables together.

Headset: Used for POTS talk/listen applications.

Getting Around

The test set uses a hierarchical menu structure. From the test set’s

startup menu, make selections by pressing the appropriate part of

to move the cursor (

CURSOR SAMPLE 01:11:2006

). Once the selection has

been made, press or an indicated key.

Throughout this User’s Manual, the following shorthand is used to

indicate how to get to a particular menu function, such as: “SYSTEM

SETUP > CLOCK”, where the “>” means to press . To return to the

previous screen, press ESC.

6 SA976

FCC ID: UEBHTT01

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE:This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful in-

terference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his

own expense.

Any changes or modiﬁcations not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate the

equipment.

Caution: Exposure to Radio Frequency Radiation.

To comply with FCC RF exposure compliance requirements, this device

must not be co-located or operating in conjunction with any other antenna

or transmitter.

7HTT

1 Physical Description

1.1 Front View

HTT

PASS/FAIL

BLUETOOTH

POWER

BATTERY

F1 F2 F3 F4

AUTO ESC

Slide this cover to access the main port panel.

SIGNAL

Figure 1 HTT Front View

Figure 1 shows the front view of the HTT. The major components

shown in this view are:

Display: This is an 8 line by 21 column LCD screen. Details of the

screen are show in Figure 2:

F1 F2 F3 F4

The scroll bar

indicates

additional

screens. Use

Pg Dn and Pg

Up to access.

EXPERT MODE MENU

VDSL VTU-R

POTS/DC/OHM

CABLE TESTING

HPNA ANALYSIS

WIRELESS (802.11)

VDSL POTS HPNA CABLE

EXPERT MODE MENU

SLM

ETHERNET

PC ACCESS

MEASUREMENT SETUP

SYSTEM SETUP

VDSL POTS HPNA CABLE

In this instance,

these F-keys

act as shortcuts

to a function.

The battery

indicates battery

life, in this case it

is about 1/2 full.

Press Pg Up or Pg Dn to access screens.

Figure 2 HTT Screen

LEDs:

PASS/FAIL: Indicates pass (green) or fail (red) results for a test.

SIGNAL: Indicates various signals specic to menu selection, such as

link up (green) and link down (red).

POWER: When the HTT is on, it is green.

BLUETOOTH: Indicates the presence of a Bluetooth network.

BATTERY: When the battery is low, it is red and the on-screen battery

indicator displays 1/4. It is green when charging.

8SA976

Keypad

: Used to page up or page down through screens. Look for Pg

Up and Pg Dn in this manual.

: Use to power up/down the HTT. To turn on, press and hold for

3 seconds and the POWER LED illuminates green. To turn off, press

and hold for 5 seconds and the POWER LED will turn off. Look for

in this manual.

F1 F2 F3 F4

: These are used to perform selections shown on the

bottom of the screen as in Figure 2. Look for F1, F2, F3, F4, or F-keys

in this manual.

AUTO

: Starts a programed Auto Test sequence with on screen prompts.

Look for AUTO

in this manual.

: Use to display the EXPERT MODE MENU. Look for MENU in this

manual.

: Use to move the cursor in the indicated direction. Look for

in this manual.

ESC

: Use to move 1 step back in the menu. Look for ESC in this manual.

: Use to invoke a selection or action. Look for in this manual.

1.2 Top Side Panel

As shown in Figure 1, slide the transparent cover to access the main

port panel shown in Figure 3:

SLM

CABLE TEST

VDSL/

POTS/DC/OHM

ETHERNET

Figure 3 Main Port Panel

This panel contains:

SLM: Signal Level Meter Coax port used to test the quality of the signal

on the back of the STB (Set Top Box).

ETHERNET: Use this Ethernet port for basic Ethernet testing.

CABLE TEST: RJ-45 port used for Cable ID, Wiremap, Cable Loss

(over both twisted pair and Coax), and Diplexer testing.

VDSL/POTS/DC/OHM: RJ-11 port is used to test VDSL, POTS, and

check for DCV and OHM.

9HTT

1.3 Right Side Panel

HEADSET HPNA HPNA

Figure 4 Right Side Panel

Pull at the bottom part of the plastic protective cover to reveal the

panel shown in Figure 4.

Note: Do not try to remove the cover as it will be damaged.

HEADSET: Use this port to connect a headset.

HPNA: F-type coax and RJ-11 ports used to test the HPNA signal

running over a coax or RJ-11 interface.

1.4 Bottom Side Panel

This side contains the DC power port. Use it to connect the supplied

AC to 5 volt DC power supply to run and charge the HTT.

1.5 Back Side

The back side contains:

Battery Compartment: Remove the screw to access the battery pack.

Refer to Section 1.5.1.

Serial Number Label: Contains the serial number along with Sunrise

Telecom contact information.

1.5.1 Battery Replacement

When the battery does not hold a charge it needs to be replaced. To

do so follow these steps:

1. Turn off the HTT.

2. Remove the one screw that retains the battery cover.

3. Pull the cover away from the chassis.

4. Pull the battery away from the chassis.

5. Insert new battery into position in the chassis.

6. Place the cover in position and secure with screw.

7. Connect the supplied AC power supply and fully charge the battery

before use.

10 SA976

1.5.2 Battery Care and Storage

Observe these basic battery care procedures in order to avoid possible

damage to the battery and to maintain it’s performance.

WARNINGS

• Failure to observe the following procedures and precautions can

result in electrolyte leaks, heat generation, bursting, re, and seri-

ous personal injury.

• Battery electrolyte is a strong colorless alkaline solution, which is

extremely corrosive and will burn skin.

- If skin comes in contact with the electrolyte from the battery,

thoroughly wash the area immediately with clean water.

- If clothing comes in contact with the electrolyte from the battery,

discard the clothing.

- If any uid from the battery comes in contact with eyes, immedi-

ately ush thoroughly with clean water and immediately consult

a doctor. The electrolyte can cause permanent loss of eyesight.

• Keep the battery out of reach of children.

CAUTIONS

• Never dispose the battery in a re.

• Never heat the battery.

• Never strike or drop the battery.

• Do not apply water, or other oxidizing agents to the battery. This will

cause corrosion and heat generation. If the battery becomes rusted,

the gas release vent may no longer operate and cause the battery

to burst.

• Do not charge the battery using an AC adapter or charger not speci-

ed by Sunrise Telecom. Charge the battery only with the Sunrise

Telecom charger/AC adapter that came with your test set.

- If the battery is not fully charged after the battery charger’s

predetermined charging period has elapsed, stop the charging

process. Prolonged charging may cause leakage of battery uid,

heat generation, and or bursting.

- Charge the battery within a temperature range of 0°C (+32°F)

to +40°C (+104°F).

• Do not use the battery if it leaks uid or changes shape; otherwise

it may cause heat generation, bursting, and re.

• Do not short circuit the battery by connecting the positive (+) and

negative (-) terminals together with electrically conductive materials,

such as lead wires, etc.

• Do not connect the battery directly to a power source or the cigarette

lighter socket in a car. Use the optional specied cigarette lighter

charger from Sunrise Telecom.

Indice

Altri manuali Sunrise telecom Apparecchiature di prova

Sunrise telecom

Sunrise telecom CaLan N1776A Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente